Every attempt to issue a read log page command lockup the controller.
The command is currently sent if the sata device includes the devlsp feature
to read out the timing data.
This attempt to read the data, locks up the controller and the device
is not recognzied correctly (failed to set xfermode) and cannot be accessed.

This was found on Freescale P1013/P1022 and T4240 CPUs
using a ATP IG mSATA 4GB with the devslp feature.

fsl-sata ff718000.sata: Sata FSL Platform/CSB Driver init
[    1.254195] scsi0 : sata_fsl
[    1.256004] ata1: SATA max UDMA/133 irq 74
[    1.370666] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x4
[    1.470671] fsl-gianfar ethernet.4: enabled errata workarounds, flags: 0x4
[    1.775584] ata1: Signature Update detected @ 504 msecs
[    1.947594] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.948366] ata1.00: ATA-8: ATP IG mSATA, 20150311, max UDMA/133
[    1.948371] ata1.00: 7732368 sectors, multi 0: LBA
[    1.948843] ata1.00: failed to get Identify Device Data, Emask 0x1
[    1.948857] ata1.00: failed to set xfermode (err_mask=0x40)
[    7.467557] ata1: Signature Update detected @ 504 msecs
[    7.639560] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    7.651320] ata1.00: failed to get Identify Device Data, Emask 0x1
[    7.651360] ata1.00: failed to set xfermode (err_mask=0x40)
[    7.655628] ata1: limiting SATA link speed to 1.5 Gbps
[    7.659458] ata1.00: limiting speed to UDMA/133:PIO3
[   13.163554] ata1: Signature Update detected @ 504 msecs
[   13.335558] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   13.347298] ata1.00: failed to get Identify Device Data, Emask 0x1
[   13.347334] ata1.00: failed to set xfermode (err_mask=0x40)
[   13.351601] ata1.00: disabled
[   13.353278] ata1: exception Emask 0x50 SAct 0x0 SErr 0x800 action 0x6 frozen t4
[   13.359281] ata1: SError: { HostInt }
[   13.361644] ata1: hard resetting link
Signed-off-by: NAndreas Werner <andreas.werner@men.de>
Signed-off-by: NTejun Heo <tj@kernel.org>

The driver was ignoring limits requested by libata.force.  The output
would look like:

fsl-sata ffe18000.sata: Sata FSL Platform/CSB Driver init
ata1: FORCE: PHY spd limit set to 1.5Gbps
ata1: SATA max UDMA/133 irq 74
ata1: Signature Update detected @ 0 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 310)
Signed-off-by: NMartin Hicks <mort@bork.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

A check for CONFIG_MPC8315_DS was added in v2.6.24. But the related
Kconfig symbol was never added to the tree. So the code behind this
check has effectively been dead for over six years. Remove it.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NTejun Heo <tj@kernel.org>

This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable.  Benefits of this change:

* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
  and CONFIG_PM_RUNTIME=y configurations

* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
  the future

* more consistent code (there are host drivers which are using the correct
  CONFIG_PM_SLEEP checks already)

The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@linaro.org>

Before this patch, I was seeing the following lockdep splat on my
MPC8315 (PPC32) target:

  [    9.086051] =================================
  [    9.090393] [ INFO: inconsistent lock state ]
  [    9.094744] 3.9.7-ajf-gc39503d #1 Not tainted
  [    9.099087] ---------------------------------
  [    9.103432] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
  [    9.109431] scsi_eh_1/39 [HC1[1]:SC0[0]:HE0:SE1] takes:
  [    9.114642]  (&(&host->lock)->rlock){?.+...}, at: [<c02f4168>] sata_fsl_interrupt+0x50/0x250
  [    9.123137] {HARDIRQ-ON-W} state was registered at:
  [    9.128004]   [<c006cdb8>] lock_acquire+0x90/0xf4
  [    9.132737]   [<c043ef04>] _raw_spin_lock+0x34/0x4c
  [    9.137645]   [<c02f3560>] fsl_sata_set_irq_coalescing+0x68/0x100
  [    9.143750]   [<c02f36a0>] sata_fsl_init_controller+0xa8/0xc0
  [    9.149505]   [<c02f3f10>] sata_fsl_probe+0x17c/0x2e8
  [    9.154568]   [<c02acc90>] driver_probe_device+0x90/0x248
  [    9.159987]   [<c02acf0c>] __driver_attach+0xc4/0xc8
  [    9.164964]   [<c02aae74>] bus_for_each_dev+0x5c/0xa8
  [    9.170028]   [<c02ac218>] bus_add_driver+0x100/0x26c
  [    9.175091]   [<c02ad638>] driver_register+0x88/0x198
  [    9.180155]   [<c0003a24>] do_one_initcall+0x58/0x1b4
  [    9.185226]   [<c05aeeac>] kernel_init_freeable+0x118/0x1c0
  [    9.190823]   [<c0004110>] kernel_init+0x18/0x108
  [    9.195542]   [<c000f6b8>] ret_from_kernel_thread+0x64/0x6c
  [    9.201142] irq event stamp: 160
  [    9.204366] hardirqs last  enabled at (159): [<c043f778>] _raw_spin_unlock_irq+0x30/0x50
  [    9.212469] hardirqs last disabled at (160): [<c000f414>] reenable_mmu+0x30/0x88
  [    9.219867] softirqs last  enabled at (144): [<c002ae5c>] __do_softirq+0x168/0x218
  [    9.227435] softirqs last disabled at (137): [<c002b0d4>] irq_exit+0xa8/0xb4
  [    9.234481]
  [    9.234481] other info that might help us debug this:
  [    9.240995]  Possible unsafe locking scenario:
  [    9.240995]
  [    9.246898]        CPU0
  [    9.249337]        ----
  [    9.251776]   lock(&(&host->lock)->rlock);
  [    9.255878]   <Interrupt>
  [    9.258492]     lock(&(&host->lock)->rlock);
  [    9.262765]
  [    9.262765]  *** DEADLOCK ***
  [    9.262765]
  [    9.268684] no locks held by scsi_eh_1/39.
  [    9.272767]
  [    9.272767] stack backtrace:
  [    9.277117] Call Trace:
  [    9.279589] [cfff9da0] [c0008504] show_stack+0x48/0x150 (unreliable)
  [    9.285972] [cfff9de0] [c0447d5c] print_usage_bug.part.35+0x268/0x27c
  [    9.292425] [cfff9e10] [c006ace4] mark_lock+0x2ac/0x658
  [    9.297660] [cfff9e40] [c006b7e4] __lock_acquire+0x754/0x1840
  [    9.303414] [cfff9ee0] [c006cdb8] lock_acquire+0x90/0xf4
  [    9.308745] [cfff9f20] [c043ef04] _raw_spin_lock+0x34/0x4c
  [    9.314250] [cfff9f30] [c02f4168] sata_fsl_interrupt+0x50/0x250
  [    9.320187] [cfff9f70] [c0079ff0] handle_irq_event_percpu+0x90/0x254
  [    9.326547] [cfff9fc0] [c007a1fc] handle_irq_event+0x48/0x78
  [    9.332220] [cfff9fe0] [c007c95c] handle_level_irq+0x9c/0x104
  [    9.337981] [cfff9ff0] [c000d978] call_handle_irq+0x18/0x28
  [    9.343568] [cc7139f0] [c000608c] do_IRQ+0xf0/0x1a8
  [    9.348464] [cc713a20] [c000fc8c] ret_from_except+0x0/0x14
  [    9.353983] --- Exception: 501 at _raw_spin_unlock_irq+0x40/0x50
  [    9.353983]     LR = _raw_spin_unlock_irq+0x30/0x50
  [    9.364839] [cc713af0] [c043db10] wait_for_common+0xac/0x188
  [    9.370513] [cc713b30] [c02ddee4] ata_exec_internal_sg+0x2b0/0x4f0
  [    9.376699] [cc713be0] [c02de18c] ata_exec_internal+0x68/0xa8
  [    9.382454] [cc713c20] [c02de4b8] ata_dev_read_id+0x158/0x594
  [    9.388205] [cc713ca0] [c02ec244] ata_eh_recover+0xd88/0x13d0
  [    9.393962] [cc713d20] [c02f2520] sata_pmp_error_handler+0xc0/0x8ac
  [    9.400234] [cc713dd0] [c02ecdc8] ata_scsi_port_error_handler+0x464/0x5e8
  [    9.407023] [cc713e10] [c02ecfd0] ata_scsi_error+0x84/0xb8
  [    9.412528] [cc713e40] [c02c4974] scsi_error_handler+0xd8/0x47c
  [    9.418457] [cc713eb0] [c004737c] kthread+0xa8/0xac
  [    9.423355] [cc713f40] [c000f6b8] ret_from_kernel_thread+0x64/0x6c

This fix was suggested by Bhushan Bharat <R65777@freescale.com>, and
was discussed in email at:

  http://linuxppc.10917.n7.nabble.com/MPC8315-reboot-failure-lockdep-splat-possibly-related-tp75162.html

Same patch successfully tested with 3.9.7.  linux-next compiled but
not tested on hardware.

This patch is based off linux-next tag next-20130819
(which is commit 66a01bae29d11916c09f9f5a937cafe7d402e4a5 )
Signed-off-by: NAnthony Foiani <anthony.foiani@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Support config RX WATER MARK via sysfs when running at run-time;
A wrokaround for fix the exception happened to some WD HDD, found on
WD3000HLFS-01G6U1, WD3000HLFS-01G6U0, some SSD disks. The read performance
is also regression (about 30%) when use default value.

According to the latest documents, 0x10 is the default value of RX WATER MARK,
but exception/performance issue happened to some disks mentioned above.

The exception log as below when testing read performance with IOZone:
ata1.00: exception Emask 0x0 SAct 0x7 SErr 0x800000 action 0x6 frozen
ata1: SError: { LinkSeq }
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:00:ff:2c:14/01:00:02:00:00/40 tag 0 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:08:ff:2d:14/01:00:02:00:00/40 tag 1 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1.00: failed command: WRITE FPDMA QUEUED
ata1.00: cmd 61/10:10:af:08:6e/00:00:12:00:00/40 tag 2 ncq 8192 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: Hardreset failed, not off-lined 0
ata1: Signature Update detected @ 504 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/133
ata1.00: device reported invalid CHS sector 0
ata1.00: device reported invalid CHS sector 0
ata1.00: device reported invalid CHS sector 0
ata1: EH complete

The exception/performance can be resolved when RX WATER MARK value is 0x16.
Signed-off-by: NQiang Liu <qiang.liu@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Correct spelling typo in various drivers.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

kfree on NULL pointer is a no-op.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The freescale V2 SATA controller checks if the received data length matches
the programmed length 'ttl', if not, it assumes that this is an error.
In ATAPI, the 'ttl' is based on max allocation length and not the actual
data transfer length, controller will raise 'DLM' (Data length Mismatch)
error bit in Hstatus register. Along with 'DLM', DE (Device error) and
FE (fatal Error) bits are also set in Hstatus register, 'E' (Internal Error)
bit is set in Serror register and CE (Command Error) and DE (Device error)
registers have the corresponding bit set. In this condition, we need to
clear errors in following way: in the service routine, based on 'DLM' flag,
HCONTROL[27] operation clears Hstatus, CE and DE registers, clear Serror
register.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NAnju Bhartiya <Anju.Bhartiya@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Adds support for interrupt coalescing feature to reduce interrupt events.
Provides a mechanism of adjusting coalescing count and timeout tick by sysfs
at runtime, so that tradeoff of latency and CPU load can be made depending
on different applications.
Signed-off-by: NQiang Liu <qiang.liu@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Configure the FSL SATA controller to the preferred, enterprise mode.
Signed-off-by: NYutaka Ando <r46913@freescale.com>
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch converts the drivers in drivers/ata/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sylvain Munaut <tnt@246tNt.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Mark Miesfeld <mmiesfeld@amcc.com>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Saves text by removing nearly duplicated text format strings by
creating ata_<foo>_printk functions and printf extension %pV.

ata defconfig size shrinks ~5% (~8KB), allyesconfig ~2.5% (~13KB)

Format string duplication comes from:

 #define ata_link_printk(link, lv, fmt, args...) do { \
       if (sata_pmp_attached((link)->ap) || (link)->ap->slave_link)    \
               printk("%sata%u.%02u: "fmt, lv, (link)->ap->print_id,   \
                      (link)->pmp , ##args); \
       else \
               printk("%sata%u: "fmt, lv, (link)->ap->print_id , ##args); \
       } while(0)

Coalesce long formats.

$ size drivers/ata/built-in.*
   text	   data	    bss	    dec	    hex	filename
 544969	  73893	 116584	 735446	  b38d6	drivers/ata/built-in.allyesconfig.ata.o
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.allyesconfig.dev_level.o
 141328	  14689	   4220	 160237	  271ed	drivers/ata/built-in.defconfig.ata.o
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.defconfig.dev_level.o
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Saves a bit of text as the call takes fewer args.

Coalesce a few formats.
Convert a few bare printks to pr_cont.

$ size drivers/ata/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.o.allyesconfig.new
 559574	  73893	 117888	 751355	  b76fb	drivers/ata/built-in.o.allyesconfig.old
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.o.defconfig.new
 149851	  14689	   4220	 168760	  29338	drivers/ata/built-in.o.defconfig.old
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

In FSL sata v2 block, the snoop bit of PRDT Word3 description
information is at bit28 instead of bit22.

This patch adds FSL sata v2 probe and resolve this difference.
Signed-off-by: NLei Xu <B33228@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

RX_WATER_MARK sets the number of locations in Rx FIFO that can be used before
the transport layer instructs the link layer to transmit HOLDS. Note that it
can take some time for the HOLDs to get to the other end, and that in the
interim there must be enough room in the FIFO to absorb all data that could
arrive.

Update the new recommended value to 16.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When a single device error is detected, the device under the error
is indicated by the error bit set in the DER. There is a one to one
mapping between register bit and devices on Port multiplier(PMP)
i.e. bit 0 represents PMP device 0 and bit 1 represents PMP device
1 etc.

Current implementation treats Device error register value as device
number not set of bits representing multiple device on PMP. It is
changed to consider bit level.

No need to check for each set bit as all command is going to be
aborted.
Signed-off-by: NAshish Kalra <B00888@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c306 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efd (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 0d5ff566 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Final step to eliminate of_platform_bus_type.  They're all just
platform drivers now.

v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration.  These will be used to implement EH exclusion.

This patch doesn't cause any behavior difference.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way.  libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.

This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions.  This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.

* sata_fsl: It already builds done_mask.  Conversion is straight
  forward.

* sata_mv: mv_process_crpb_response() no longer checks for illegal
  completions, it just returns whether the tag is completed or not.
  mv_process_crpb_entries() builds done_mask from it and passes it to
  ata_qc_complete_multiple() which will check for illegal completions.

* sata_nv adma: Similar to sata_mv.  nv_adma_check_cpb() now just
  returns the tag status and nv_adma_interrupt() builds done_mask from
  it and passes it to ata_qc_complete_multiple().

* sata_nv swncq: It already builds done_mask.  Drop unnecessary
  illegal transition checks and call ata_qc_complete_multiple().

In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

of_device is just an alias for platform_device, so remove it entirely.  Also
replace to_of_device() with to_platform_device() and update comment blocks.

This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.

@@
@@
-struct of_device
+struct platform_device
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NDavid S. Miller <davem@davemloft.net>

Make the following changes to prepare for NCQ command completion
update.  Changes made by this patch don't cause any functional
difference.

* sata_fsl_host_intr(): rename the local variable qc_active to
  done_mask as that's what it is.

* mv_process_crpb_response(): restructure if clause for easier update.

* nv_adma_interrupt(): drop unnecessary error variable.

* nv_swncq_sdbfis(): drop unnecessary nr_done and return 0 on success.
  Typo fix.

* nv_swncq_dmafis(): drop unused return value and return void.

* nv_swncq_host_interrupt(): drop unnecessary return value handling.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver.  This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.

This patch is a pretty mechanical change.  The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial.  This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSean MacLennan <smaclennan@pikatech.com>

The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated.  This patch
makes all readers of these elements use device.of_node instead.

(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: NAshish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Split sata_fsl_softreset() into hard and soft resets to make
error-handling more efficient & device and PMP detection more
reliable.

Also includes fix for PMP support, driver tested with Sil3726,
Sil4726 & Exar PMP controllers.

[AV: Also fixes resuming from deep sleep on MPC8315 CPUs]
Signed-off-by: NJiang Yutang <b14898@freescale.com>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix for non-ncq & ncq commands causing timeouts when both are issued
simultaneously to the same device.
Signed-off-by: NAshish Kalra <Ashish.Kalra@freescale.com>
[fixed to be actual compileable C code -jg]
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The bit 11 of command description is reserved bit in Freescale
SATA controller and needs to be set to '1'.  This is needed to
make sure the last write from the controller to the buffer
descriptor is seen before an interrupt is raised.
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We we build with dma_addr_t as a 64-bit quantity we get:

drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:340: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>