The bnxt_hwrm_reserve_{pf|vf}_rings() functions are very similar to
the bnxt_hwrm_check_{pf|vf}_rings() functions.  Refactor the former
so that the latter can make use of common code in the next patch.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 664fcf12 (net: phy: Threaded interrupts allow some simplification)
the phy_interrupt system was changed to use a traditional threaded
interrupt scheme instead of a workqueue approach.

With this change, the phy status check moved into phy_change, which
did not report back to the caller whether or not the interrupt was
handled. This means that, in the case of a shared phy interrupt,
only the first phydev's interrupt registers are checked (since
phy_interrupt() would always return IRQ_HANDLED). This leads to
interrupt storms when it is a secondary device that's actually the
interrupt source.
Signed-off-by: NBrad Mouring <brad.mouring@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Max delat_t should be the full_bucket/rate instead of the full_bucket.
Also report EINVAL if the rate is zero.

Fixes: 96fbc13d ("openvswitch: Add meter infrastructure")
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: Nzhangliping <zhangliping02@baidu.com>
Acked-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a macvlan device on top of a lowerdev that supports
the xfrm offloads fails with a new regression:
  # ip link add link ens1f0 mv0 type macvlan
  RTNETLINK answers: Operation not permitted

Tracing down the failure shows that the macvlan device inherits
the NETIF_F_HW_ESP and NETIF_F_HW_ESP_TX_CSUM feature flags
from the lowerdev, but with no dev->xfrmdev_ops API filled
in, it doesn't actually support xfrm.  When the request is
made to add the new macvlan device, the XFRM listener for
NETDEV_REGISTER calls xfrm_api_check() which fails the new
registration because dev->xfrmdev_ops is NULL.

The macvlan creation succeeds when we filter out the ESP
feature flags in macvlan_fix_features(), so let's filter them
out like we're already filtering out ~NETIF_F_NETNS_LOCAL.
When XFRM support is added in the future, we can add the flags
into MACVLAN_FEATURES.

This same problem could crop up in the future with any other
new feature flags, so let's filter out any flags that aren't
defined as supported in macvlan.

Fixes: d77e38e6 ("xfrm: Add an IPsec hardware offloading API")
Reported-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

William Tu says:

====================
a couple of erspan fixes

The series fixes a couple of erspan issues.
The first patch adds the erspan v2 proto type to the ip6 tunnel lookup.
The second patch improves the error handling when users screws the
version number in metadata.  The final patch makes sure the skb has
enough headroom for pushing erspan header when xmit.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds skb_cow_header() to ensure enough headroom
at ip6erspan_tunnel_xmit before pushing the erspan header
to the skb.
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When users fill in incorrect erspan version number through
the struct erspan_metadata uapi, current code skips pushing
the erspan header but continue pushing the gre header, which
is incorrect.  The patch fixes it by returning error.
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds the erspan v2 proto in ip6gre_tunnel_lookup
so the erspan v2 tunnel can be found correctly.
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: ACL and mirroring fixes

The first patch fixes offload of rules using the 'pass' action. Instead
of continuing to evaluate lower priority rules, the binding is
terminated and the packet proceeds to the bridge and router blocks on
ingress, or goes out of the port on egress.

Second patch prevents the user from mirroring more than once from a
given {Port, Direction} as this is not supported by the device.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Spectrum ASIC doesn't support mirroring more than once from a single
binding point (which is a port-direction pair). Therefore detect that a
second binding of a given binding point is attempted.

To that end, extend struct mlxsw_sp_span_inspected_port to track whether
a given binding point is bound or not. Extend
mlxsw_sp_span_entry_port_find() to look for ports based on the full
unique key: port number, direction, and boundness.

Besides fixing the overt bug where configured mirrors are not offloaded,
this also fixes a more subtle bug: mlxsw_sp_span_inspected_port_del()
just defers to mlxsw_sp_span_entry_bound_port_find(), and that used to
find the first port with the right number (disregarding the type). Thus
by adding and removing egress and ingress mirrors in the right order,
one could trick the system into believing it has no egress mirrors when
in fact it did have some. That then caused that
mlxsw_sp_span_port_mtu_update() didn't update mirroring buffer when MTU
was changed.

Fixes: 763b4b70 ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ok GACT action, TERMINATE binding_cmd should be used in action set
passed down to HW.

Fixes: b2925957 ("mlxsw: spectrum_flower: Offload "ok" termination action")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reported-by: NAlexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jason Wang says:

====================
Several fixes for vhost_net ptr_ring usage

This small series try to fix several bugs of ptr_ring usage in
vhost_net. Please review.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit fc72d1d5 ("tuntap: XDP transmission"), we can
actually queueing XDP pointers in the pointer ring, so we should
examine the pointer type before freeing the pointer.

Fixes: fc72d1d5 ("tuntap: XDP transmission")
Reported-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get pointer ring from the exported sock, this means we should keep
rx_ring and vq->private synced during both vq stop and backend set,
otherwise we may see stale rx_ring.

Fixes: c67df11f ("vhost_net: try batch dequing from skb array")
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

KMSAN reported a use of uninit memory in vhost_net_buf_unproduce()
while trying to access n->vqs[VHOST_NET_VQ_TX].rx_ring:

==================================================================
BUG: KMSAN: use of uninitialized memory in vhost_net_buf_unproduce+0x7bb/0x9a0 drivers/vho
et.c:170
CPU: 0 PID: 3021 Comm: syz-fuzzer Not tainted 4.16.0-rc4+ #3853
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x185/0x1d0 lib/dump_stack.c:53
 kmsan_report+0x142/0x1f0 mm/kmsan/kmsan.c:1093
 __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:676
 vhost_net_buf_unproduce+0x7bb/0x9a0 drivers/vhost/net.c:170
 vhost_net_stop_vq drivers/vhost/net.c:974 [inline]
 vhost_net_stop+0x146/0x380 drivers/vhost/net.c:982
 vhost_net_release+0xb1/0x4f0 drivers/vhost/net.c:1015
 __fput+0x49f/0xa00 fs/file_table.c:209
 ____fput+0x37/0x40 fs/file_table.c:243
 task_work_run+0x243/0x2c0 kernel/task_work.c:113
 tracehook_notify_resume include/linux/tracehook.h:191 [inline]
 exit_to_usermode_loop arch/x86/entry/common.c:166 [inline]
 prepare_exit_to_usermode+0x349/0x3b0 arch/x86/entry/common.c:196
 syscall_return_slowpath+0xf3/0x6d0 arch/x86/entry/common.c:265
 do_syscall_64+0x34d/0x450 arch/x86/entry/common.c:292
...
origin:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:303 [inline]
 kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:213
 kmsan_kmalloc_large+0x6f/0xd0 mm/kmsan/kmsan.c:392
 kmalloc_large_node_hook mm/slub.c:1366 [inline]
 kmalloc_large_node mm/slub.c:3808 [inline]
 __kmalloc_node+0x100e/0x1290 mm/slub.c:3818
 kmalloc_node include/linux/slab.h:554 [inline]
 kvmalloc_node+0x1a5/0x2e0 mm/util.c:419
 kvmalloc include/linux/mm.h:541 [inline]
 vhost_net_open+0x64/0x5f0 drivers/vhost/net.c:921
 misc_open+0x7b5/0x8b0 drivers/char/misc.c:154
 chrdev_open+0xc28/0xd90 fs/char_dev.c:417
 do_dentry_open+0xccb/0x1430 fs/open.c:752
 vfs_open+0x272/0x2e0 fs/open.c:866
 do_last fs/namei.c:3378 [inline]
 path_openat+0x49ad/0x6580 fs/namei.c:3519
 do_filp_open+0x267/0x640 fs/namei.c:3553
 do_sys_open+0x6ad/0x9c0 fs/open.c:1059
 SYSC_openat+0xc7/0xe0 fs/open.c:1086
 SyS_openat+0x63/0x90 fs/open.c:1080
 do_syscall_64+0x2f1/0x450 arch/x86/entry/common.c:287
==================================================================

Fixes: c67df11f ("vhost_net: try batch dequing from skb array")
Signed-off-by: NAlexander Potapenko <glider@google.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables AVE_GI_RXDROP interrupt factor. This factor indicates
depletion of Rx descriptors and the handler counts the number
of dropped packets.
Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As well as the basic conversion, I noticed that a lot of the
SCTP code checks gso_type without first checking skb_is_gso()
so I have added that where appropriate.

Also, document the helper.

Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A tun device type can trivially be set to arbitrary value using
TUNSETLINK ioctl().

Therefore, lowpan_device_event() must really check that ieee802154_ptr
is not NULL.

Fixes: 2c88b528 ("ieee802154: 6lowpan: remove check on null")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Acked-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following slab-out-of-bounds kasan report in
ndisc_fill_redirect_hdr_option when the incoming ipv6 packet is not
linear and the accessed data are not in the linear data region of orig_skb.

[ 1503.122508] ==================================================================
[ 1503.122832] BUG: KASAN: slab-out-of-bounds in ndisc_send_redirect+0x94e/0x990
[ 1503.123036] Read of size 1184 at addr ffff8800298ab6b0 by task netperf/1932

[ 1503.123220] CPU: 0 PID: 1932 Comm: netperf Not tainted 4.16.0-rc2+ #124
[ 1503.123347] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-2.fc27 04/01/2014
[ 1503.123527] Call Trace:
[ 1503.123579]  <IRQ>
[ 1503.123638]  print_address_description+0x6e/0x280
[ 1503.123849]  kasan_report+0x233/0x350
[ 1503.123946]  memcpy+0x1f/0x50
[ 1503.124037]  ndisc_send_redirect+0x94e/0x990
[ 1503.125150]  ip6_forward+0x1242/0x13b0
[...]
[ 1503.153890] Allocated by task 1932:
[ 1503.153982]  kasan_kmalloc+0x9f/0xd0
[ 1503.154074]  __kmalloc_track_caller+0xb5/0x160
[ 1503.154198]  __kmalloc_reserve.isra.41+0x24/0x70
[ 1503.154324]  __alloc_skb+0x130/0x3e0
[ 1503.154415]  sctp_packet_transmit+0x21a/0x1810
[ 1503.154533]  sctp_outq_flush+0xc14/0x1db0
[ 1503.154624]  sctp_do_sm+0x34e/0x2740
[ 1503.154715]  sctp_primitive_SEND+0x57/0x70
[ 1503.154807]  sctp_sendmsg+0xaa6/0x1b10
[ 1503.154897]  sock_sendmsg+0x68/0x80
[ 1503.154987]  ___sys_sendmsg+0x431/0x4b0
[ 1503.155078]  __sys_sendmsg+0xa4/0x130
[ 1503.155168]  do_syscall_64+0x171/0x3f0
[ 1503.155259]  entry_SYSCALL_64_after_hwframe+0x42/0xb7

[ 1503.155436] Freed by task 1932:
[ 1503.155527]  __kasan_slab_free+0x134/0x180
[ 1503.155618]  kfree+0xbc/0x180
[ 1503.155709]  skb_release_data+0x27f/0x2c0
[ 1503.155800]  consume_skb+0x94/0xe0
[ 1503.155889]  sctp_chunk_put+0x1aa/0x1f0
[ 1503.155979]  sctp_inq_pop+0x2f8/0x6e0
[ 1503.156070]  sctp_assoc_bh_rcv+0x6a/0x230
[ 1503.156164]  sctp_inq_push+0x117/0x150
[ 1503.156255]  sctp_backlog_rcv+0xdf/0x4a0
[ 1503.156346]  __release_sock+0x142/0x250
[ 1503.156436]  release_sock+0x80/0x180
[ 1503.156526]  sctp_sendmsg+0xbb0/0x1b10
[ 1503.156617]  sock_sendmsg+0x68/0x80
[ 1503.156708]  ___sys_sendmsg+0x431/0x4b0
[ 1503.156799]  __sys_sendmsg+0xa4/0x130
[ 1503.156889]  do_syscall_64+0x171/0x3f0
[ 1503.156980]  entry_SYSCALL_64_after_hwframe+0x42/0xb7

[ 1503.157158] The buggy address belongs to the object at ffff8800298ab600
                which belongs to the cache kmalloc-1024 of size 1024
[ 1503.157444] The buggy address is located 176 bytes inside of
                1024-byte region [ffff8800298ab600, ffff8800298aba00)
[ 1503.157702] The buggy address belongs to the page:
[ 1503.157820] page:ffffea0000a62a00 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 1503.158053] flags: 0x4000000000008100(slab|head)
[ 1503.158171] raw: 4000000000008100 0000000000000000 0000000000000000 00000001800e000e
[ 1503.158350] raw: dead000000000100 dead000000000200 ffff880036002600 0000000000000000
[ 1503.158523] page dumped because: kasan: bad access detected

[ 1503.158698] Memory state around the buggy address:
[ 1503.158816]  ffff8800298ab900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.158988]  ffff8800298ab980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.159165] >ffff8800298aba00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1503.159338]                    ^
[ 1503.159436]  ffff8800298aba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159610]  ffff8800298abb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159785] ==================================================================
[ 1503.159964] Disabling lock debugging due to kernel taint

The test scenario to trigger the issue consists of 4 devices:
- H0: data sender, connected to LAN0
- H1: data receiver, connected to LAN1
- GW0 and GW1: routers between LAN0 and LAN1. Both of them have an
  ethernet connection on LAN0 and LAN1
On H{0,1} set GW0 as default gateway while on GW0 set GW1 as next hop for
data from LAN0 to LAN1.
Moreover create an ip6ip6 tunnel between H0 and H1 and send 3 concurrent
data streams (TCP/UDP/SCTP) from H0 to H1 through ip6ip6 tunnel (send
buffer size is set to 16K). While data streams are active flush the route
cache on HA multiple times.
I have not been able to identify a given commit that introduced the issue
since, using the reproducer described above, the kasan report has been
triggered from 4.14 and I have not gone back further.
Reported-by: NJianlin Shi <jishi@redhat.com>
Reviewed-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
hv_netvsc: fix multicast flags and sync

This set of patches deals with the handling of multicast flags
and addresses in transparent VF mode. The recent set of patches
(in linux-net) had a couple of bugs.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dev_uc/mc_sync calls need to have the device address list
locked. This was spotted by running with lockdep enabled.

Fixes: bee9d41b ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx_mode operation handler is different than other callbacks
in that is not always called with rtnl held. Therefore use
RCU to ensure that references are valid.

Fixes: bee9d41b ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netvsc driver can get repeated calls to netvsc_rx_mode during
network setup; each of these calls ends up scheduling the lower
layers to update tha packet filter. This update requires an
request/response to the host. So avoid doing this if we already
know that the correct packet filter value is set.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent change to not always enable all multicast and broadcast
was broken; meant to set filter, not change flags.

Fixes: 009f766c ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2018-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo:

====================
wireless-drivers fixes for 4.16

Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.

iwlwifi

* fix a bogus warning when freeing a TFD

* fix severe throughput problem with 9000 series

* fix for a bug that caused queue hangs in certain situations

* fix for an issue with IBSS

* fix an issue with rate-scaling in AP-mode

* fix Channel Switch Announcement (CSA) issues with count 0 and 1

* some firmware debugging fixes

* remov a wrong error message when removing keys

* fix a firmware sysassert most usually triggered in IBSS

* a couple of fixes on multicast queues

* a fix with CCMP 256

rtlwifi

* fix loss of signal for rtl8723be

brcmfmac

* add possibility to obtain firmware error

* fix P2P_DEVICE ethernet address generation
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pretty minor: just SKB_GSO_TCP  -> SKB_GSO_TCPV4 and
                   SKB_GSO_TCP6 -> SKB_GSO_TCPV6.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __send_and_alloc_skb() receives a skb ptr as a parameter but in
case it fails the skb is not valid:
- Send failed and released the skb internally.
- Allocation failed.

The current code tries to release the skb in case of failure which
causes redundant freeing.

Fixes: 9b00cf2d ("team: implement multipart netlink messages for options transfers")
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-03-08

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix various BPF helpers which adjust the skb and its GSO information
   with regards to SCTP GSO. The latter is a special case where gso_size
   is of value GSO_BY_FRAGS, so mangling that will end up corrupting
   the skb, thus bail out when seeing SCTP GSO packets, from Daniel(s).

2) Fix a compilation error in bpftool where BPF_FS_MAGIC is not defined
   due to too old kernel headers in the system, from Jiri.

3) Increase the number of x64 JIT passes in order to allow larger images
   to converge instead of punting them to interpreter or having them
   rejected when the interpreter is not built into the kernel, from Daniel.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Cilium some of the main programs we run today are hitting 9 passes
on x64's JIT compiler, and we've had cases already where we surpassed
the limit where the JIT then punts the program to the interpreter
instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON
or insertion failures due to the prog array owner being JITed but the
program to insert not (both must have the same JITed/non-JITed property).

One concrete case the program image shrunk from 12,767 bytes down to
10,288 bytes where the image converged after 16 steps. I've measured
that this took 340us in the JIT until it converges on my i7-6600U. Thus,
increase the original limit we had from day one where the JIT covered
cBPF only back then before we run into the case (as similar with the
complexity limit) where we trip over this and hit program rejections.
Also add a cond_resched() into the compilation loop, the JIT process
runs without any locks and may sleep anyway.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

instantiation of VF's on different adapters fails, copy
adapter index and chip type to PF0-3 adapter instances
to fix the issue.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with v4.16-rc1 we've been seeing a higher than usual number
of requests for the kernel to load networking modules, even on events
which shouldn't trigger a module load (e.g. ioctl(TCGETS)).  Stephen
Smalley suggested the problem may lie in commit 44c02a2c
("dev_ioctl(): move copyin/copyout to callers") which moves changes
the network dev_ioctl() function to always call dev_load(),
regardless of the requested ioctl.

This patch moves the dev_load() calls back into the individual ioctls
while preserving the rest of the original patch.
Reported-by: NDominick Grift <dac.override@gmail.com>
Suggested-by: NStephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NPaul Moore <paul@paul-moore.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the connection is aborted, there is no point in
keeping the packets on the write queue until the connection
is closed.

Similar to a27fd7a8 ('tcp: purge write queue upon RST'),
this is essential for a correct MSG_ZEROCOPY implementation,
because userspace cannot call close(fd) before receiving
zerocopy signals even when the connection is aborted.

Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dccp_disconnect() sets 'dp->dccps_hc_tx_ccid' tx handler to NULL,
therefore if DCCP socket is disconnected and dccp_sendmsg() is
called after it, it will cause a NULL pointer dereference in
dccp_write_xmit().

This crash and the reproducer was reported by syzbot. Looks like
it is reproduced if commit 69c64866 ("dccp: CVE-2017-8824:
use-after-free in DCCP code") is applied.

Reported-by: syzbot+f99ab3887ab65d70f816@syzkaller.appspotmail.com
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

syzkaller found an issue caused by lack of sufficient checks
in l2tp_tunnel_create()

RAW sockets can not be considered as UDP ones for instance.

In another patch, we shall replace all pr_err() by less intrusive
pr_debug() so that syzkaller can find other bugs faster.
Acked-by: NGuillaume Nault <g.nault@alphalink.fr>
Acked-by: NJames Chapman <jchapman@katalix.com>

==================================================================
BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
dst_release: dst:00000000d53d0d0f refcnt:-1
Write of size 1 at addr ffff8801d013b798 by task syz-executor3/6242

CPU: 1 PID: 6242 Comm: syz-executor3 Not tainted 4.16.0-rc2+ #253
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x24d lib/dump_stack.c:53
 print_address_description+0x73/0x250 mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report+0x23b/0x360 mm/kasan/report.c:412
 __asan_report_store1_noabort+0x17/0x20 mm/kasan/report.c:435
 setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69
 l2tp_tunnel_create+0x1354/0x17f0 net/l2tp/l2tp_core.c:1596
 pppol2tp_connect+0x14b1/0x1dd0 net/l2tp/l2tp_ppp.c:707
 SYSC_connect+0x213/0x4a0 net/socket.c:1640
 SyS_connect+0x24/0x30 net/socket.c:1621
 do_syscall_64+0x280/0x940 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x42/0xb7

Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

inet_evict_bucket() iterates global list, and
several tasks may call it in parallel. All of
them hash the same fq->list_evictor to different
lists, which leads to list corruption.

This patch makes fq be hashed to expired list
only if this has not been made yet by another
task. Since inet_frag_alloc() allocates fq
using kmem_cache_zalloc(), we may rely on
list_evictor is initially unhashed.

The problem seems to exist before async
pernet_operations, as there was possible to have
exit method to be executed in parallel with
inet_frags::frags_work, so I add two Fixes tags.
This also may go to stable.

Fixes: d1fe1944 "inet: frag: don't re-use chainlist for evictor"
Fixes: f84c6821 "net: Convert pernet_subsys, registered from inet_init()"
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The smsc911x driver will crash if it is rmmod'ed while the netdev
is up like:

Call trace:
  phy_detach+0x94/0x150
  phy_disconnect+0x40/0x50
  smsc911x_stop+0x104/0x128 [smsc911x]
  __dev_close_many+0xb4/0x138
  dev_close_many+0xbc/0x190
  rollback_registered_many+0x140/0x460
  rollback_registered+0x68/0xb0
  unregister_netdevice_queue+0x100/0x118
  unregister_netdev+0x28/0x38
  smsc911x_drv_remove+0x58/0x130 [smsc911x]
  platform_drv_remove+0x30/0x50
  device_release_driver_internal+0x15c/0x1f8
  driver_detach+0x54/0x98
  bus_remove_driver+0x64/0xe8
  driver_unregister+0x34/0x60
  platform_driver_unregister+0x20/0x30
  smsc911x_cleanup_module+0x14/0xbca8 [smsc911x]
  SyS_delete_module+0x1e8/0x238
  __sys_trace_return+0x0/0x4

This is caused by the mdiobus being unregistered/free'd
and the code in phy_detach() attempting to manipulate mdio
related structures from unregister_netdev() calling close()

To fix this, we delay the mdiobus teardown until after
the netdev is deregistered.
Reported-by: NMatt Sealey <matt.sealey@arm.com>
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, administrative MTU changes on a given netdevice are
not reflected on route exceptions for MTU-less routes, with a
set PMTU value, for that device:

 # ip -6 route get 2001:db8::b
 2001:db8::b from :: dev vti_a proto kernel src 2001:db8::a metric 256 pref medium
 # ping6 -c 1 -q -s10000 2001:db8::b > /dev/null
 # ip netns exec a ip -6 route get 2001:db8::b
 2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
     cache expires 571sec mtu 4926 pref medium
 # ip link set dev vti_a mtu 3000
 # ip -6 route get 2001:db8::b
 2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
     cache expires 571sec mtu 4926 pref medium
 # ip link set dev vti_a mtu 9000
 # ip -6 route get 2001:db8::b
 2001:db8::b from :: dev vti_a src 2001:db8::a metric 0
     cache expires 571sec mtu 4926 pref medium

The first issue is that since commit fb56be83 ("net-ipv6: on
device mtu change do not add mtu to mtu-less routes") we don't
call rt6_exceptions_update_pmtu() from rt6_mtu_change_route(),
which handles administrative MTU changes, if the regular route
is MTU-less.

However, PMTU exceptions should be always updated, as long as
RTAX_MTU is not locked. Keep the check for MTU-less main route,
as introduced by that commit, but, for exceptions,
call rt6_exceptions_update_pmtu() regardless of that check.

Once that is fixed, one problem remains: MTU changes are not
reflected if the new MTU is higher than the previous one,
because rt6_exceptions_update_pmtu() doesn't allow that. We
should instead allow PMTU increase if the old PMTU matches the
local MTU, as that implies that the old MTU was the lowest in the
path, and PMTU discovery might lead to different results.

The existing check in rt6_mtu_change_route() correctly took that
case into account (for regular routes only), so factor it out
and re-use it also in rt6_exceptions_update_pmtu().

While at it, fix comments style and grammar, and try to be a bit
more descriptive.
Reported-by: NXiumei Mu <xmu@redhat.com>
Fixes: fb56be83 ("net-ipv6: on device mtu change do not add mtu to mtu-less routes")
Fixes: f5bbe7ee ("ipv6: prepare rt6_mtu_change() for exception table")
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.
Signed-off-by: NHemanth Puranik <hpuranik@codeaurora.org>
Acked-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rdma requires ILT Memory to be allocated for it's QPs.
Each ILT entry points to a page used by several Rdma QPs.
To avoid allocating all the memory in advance, the rdma
implementation dynamically allocates memory as more QPs are
added, however it does not dynamically free the memory.
The memory should have been freed on rmmod qedr, but isn't.
This patch adds the memory freeing on rmmod qedr (currently
it will be freed with qed is removed).

An outcome of this bug, is that if qedr is unloaded and loaded
without unloaded qed, there will be no more RoCE traffic.

The reason these are related, is that the logic of detecting the
first QP ever opened is by asking whether ILT memory for RoCE has
been allocated.

In addition, this patch modifies freeing of the Task context to
always use the PROTOCOLID_ROCE and not the protocol passed,
this is because task context for iWARP and ROCE both use the
ROCE protocol id, as opposed to the connection context.

Fixes: dbb799c3 ("qed: Initialize hardware for new protocols")
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>