Rework the locking in m2m driver to assure proper operation on SMP systems.

When job_abort or stop_streaming was called to immediately shutdown
a memory-to-memory transaction video buffers scheduled for processing
were never returned to vb2 and v4l2_m2m_job_finish was not called
which led to hanging.

Correct this and also return the unprocessed buffers to vb2 marking
them as erroneous, in case the end of frame interrupt do not occur.
Reported-by: NSewoon Park <seuni.park@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In some cases fimc H/W did not stop although there were no output
buffers available. So the capture deactivation interrupt routine
is modified and the state of ST_CAPT_RUN is cleared only
in the LAST-IRQ call.

After LAST-IRQ is generated, H/W pointer will be skipped by 1 frame.
(reference by user manual) So, S/W pointer should be increased too.

Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: NSungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds callback functions, stop_streaming and job_abort,
to abort or finish any DMA in progress. stop_streaming is called
by videobuf2 framework and job_abort is called by m2m framework.
ST_M2M_PEND state is added to discard the next job.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Horizontal and vertical scaling range are according to the following equations.
If (SRC_Width >= 64 x DST_Width) { Exit(-1);  /* Out of Horizontal scale range}
If (SRC_Height >= 64 x DST_Height) { Exit(-1);  /* Out of Vertical scale range}

fimc_check_scaler_ratio() is used to check if horizontal and vertical
scale range are valid or not. To use fimc_check_scaler_ratio,
source and destination format should be set by VIDIOC_S_FMT.
And in case of scaling up, it doesn't have to check the scale range.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The main scaler has four SFRs for main scaler ratio depending on FIMC version.
FIMC 4.x has only two SFRs and FIMC 5.x has four SFRs for main scaler.
Those are MainHorRatio, MainHorRatio_ext, MainVerRatio and MainverRatio_ext.

The FIMC 5.x has 15 bit resolution for scaling ratio as below.
{MainHorRatio,MainHorRatio_ext} = {[14:6],[5:0]}.
{MainVerRatio,MainVerRatio_ext} = {[14:6],[5:0]}.
MainHorRatio = CISCCTRL[24:16], MainHorRatio_ext = CIEXTEN[15:10]
MainVerRatio = CISCCTRL[8:0],   MainVerRatio_ext = CIEXTEN[5:0]

This patch supports FIMC 4.x and FIMC 5.x using platform_device_id::driver_data.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some color formats are mismatched in s5p-fimc driver.
CIOCTRL[1:0], order422_out, should be set 2b'00 not 2b'11
to use V4L2_PIX_FMT_YUYV. Because in V4L2 standard V4L2_PIX_FMT_YUYV means
"start + 0: Y'00 Cb00 Y'01 Cr00 Y'02 Cb01 Y'03 Cr01". According to datasheet
2b'00 is right value for V4L2_PIX_FMT_YUYV.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Map all (0, 90, 180, 270) deg counterclockwise rotation and
horizontal and vertical flip controls to (0, 90) deg rotation,
horizontal and vertical flip transformations available
in the device.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Conversion to multiplanar color formats and minor cleanup.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Porting to videobuf 2 and minor cleanup.
Separate videobuf_queue_ops are are created for m2m
and capture video nodes.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add missing newlines.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There was an unlock missing if kzalloc() failed.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Enable FIMC operation on S5PC210 (S5PV310) SoCs. This a minimal
adaptation to obtain functionality of older FIMC IP revisions
(S5PC100, S5PC110) on S5PC210 SOcs.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a video device driver per each FIMC entity to support
the camera capture input mode. Video capture node is registered
only if CCD sensor data is provided through driver's platfrom data
and board setup code.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is not necessary to lock both capture and output buffer queue while
setting format for single queue.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Due to errorneous swapping of image dimensions the rotation
control was not handled properly in subsequent calls.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Register access functions refactored for camera capture interface
control. Removed the workqueue since it was only useful for FIFO
output mode which is not supported at this time.
Fixed errors on module unload. Comments and whitespace cleanup.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Missed a few init functions on non-Intel platforms the first time :-(
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix DMA engine pixel offset calculation for 3-planar YUV formats.
On S5PV210 SoCs horizontal offset is applied as number of pixels,
not bytes per line.

[mchehab@redhat.com: CodingStyle cleanup]
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On failed create_workqueue() fimc_probe() was returning 0.
Signed-off-by: NPawel Osciak <p.osciak@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If we return directly here then we miss out on some mutex_unlock()s
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NPawel Osciak <p.osciak@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver exports a video device node per each camera interface/
video postprocessor (FIMC) device contained in Samsung S5P SoC series.
The driver is based on v4l2-mem2mem framework.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NPawel Osciak <p.osciak@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>