- 11 1月, 2011 8 次提交
-
-
由 Stanislaw Gruszka 提交于
pcmcia_request_irq() and pcmcia_enable_device() are intended to be called from process context (first function allocate memory with GFP_KERNEL, second take a mutex). We can not take spin lock and call them. It's safe to move spin lock after pcmcia_enable_device() as we still hold off IRQ until dev->base_addr is 0 and driver will not proceed with interrupts when is not ready. Patch resolves: https://bugzilla.redhat.com/show_bug.cgi?id=643758 Reported-and-tested-by: rbugz@biobind.com Cc: stable@kernel.org # 2.6.34+ Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Indan Zupancic 提交于
This is an attempt to fix a long standing open bug: http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334 The interrupt handler checks for INTA being -1, apparently that means that the hardware is gone. But the interrupt handler defers actual interrupt processing to a tasklet. By the time the tasklet is run and checks INTA again, the hardware might be gone and INTA be -1, which confuses the driver because all event bits are set. The patch applies to 2.6.37. Signed-off-by: NIndan Zupancic <indan@nul.nu> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the firmware that "the frame's sequence number has already been set by the application." Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for frames which lack a valid sequence number and either the driver or firmware has to assign one. Yup, it's the exact opposite! Cc: <stable@kernel.org> Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
The chainmask value along with other configuration has to be set on the target for packet injection. Fix this and also move the monitor interface addition before the channel set segment to ensure that the opmode is updated properly. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset" uncondionally added aborting RX DMA in a HW reset, though it is a bit unclear as to why this is needed. Anyway, RX DMA is handled in the target for USB devices, and this would interfere with normal operations (scanning etc.), so fix this. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Hardcode the output voltage of x-PA bias LDO to the lowest value for UB94. The card doesn't get too hot now. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
AR9287 based devices have issues with ADC gain calibration which would cause uplink throughput drops in HT40 mode. Remove ADC gain from the supported calibration algorithms. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
USB devices do not require the chip test routine. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 1月, 2011 26 次提交
-
-
由 Alexander Duyck 提交于
This change fixes several issues found in ntuple filtering while I was doing the ATR refactor. Specifically I updated the masks to work correctly with the latest version of ethtool, I cleaned up the exception handling and added detailed error output when a filter is rejected, and corrected several bits that were set incorrectly in ixgbe_type.h. The previous version of this patch included a printk that was left over from me fixing the filter setup. This patch does not include that printk. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Tested-by: NStephen Ko <stephen.s.ko@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
This change adds a compressed input type for atr signature hash computation. It also drops the use of the set functions when setting up the ATR input since we can then directly setup the hash input as two dwords that can be stored and passed as registers. With these changes the cost of computing the has is low enough that we can perform a hash computation on each TCP SYN flagged packet allowing us to drop the number of flow director misses considerably in tests such as netperf TCP_CRR. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Tested-by: NStephen Ko <stephen.s.ko@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
This change cleans up the layout of the flow director data, and the algorithm used to calculate the hash resulting in a 35x / 3500% performance increase versus the old flow director hash computation. The overall effect is only a 1% increase in transactions per second though due to the fact that only 1 packet in 20 are actually hashed upon. TCP_RR before: Socket Size Request Resp. Elapsed Trans. Send Recv Size Size Time Rate bytes Bytes bytes bytes secs. per sec 16384 87380 1 1 60.00 23059.27 16384 87380 TCP_RR after: Socket Size Request Resp. Elapsed Trans. Send Recv Size Size Time Rate bytes Bytes bytes bytes secs. per sec 16384 87380 1 1 60.00 23239.98 16384 87380 Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Tested-by: NStephen Ko <stephen.s.ko@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
When disable the Rx logic globally, we would also want to disable the per Rx queue receive logic by per queue Rx control register RXDCTL so no more DMA is happening from the packet buffer to the receive buffer associated with the Rx ring, before we start unmapping Rx ring receive buffer. The hardware may take max of 100us before the corresponding Rx queue is really disabled. Added ixgbe_disable_rx_queue() for this purpose. Signed-off-by: NYi Zou <yi.zou@intel.com> Tested-by: NStephen Ko <stephen.s.ko@intel.com> Tested-by: NRoss Brattain <ross.b.brattain@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dirk Brandewie 提交于
This patch adds support for the gigabit phys present on the CE4100 reference platforms. Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com> Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
82574 needs to configure Low Power Link Up (or LPLU) differently than the other parts in the 8257x family supported by the driver. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
Some Phys supported by the driver do not remain powered off across a reset of the device when the interface is down, e.g. on 82571, but not on 82574. This patch powers down (only when WoL is disabled) the PHY after a reset if the interface is down and the ethtool diagnostics are not currently running. The ethtool diagnostic function required a minor re-factor as a result, and the e1000_[get|put]_hw_control() functions are renamed since they are no longer static to netdev.c as they are needed by the ethtool diagnostics. A couple minor whitespace issues were cleaned up, too. Reported-by: NArthur Jones <ajones@riverbed.com> Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
For the 82579 jumbo frame workaround, there is no need to re-write the CRC calculation functionality already found in the kernel's ether_crc_le(). Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
Use string functions with bounds checking rather than their non-bounds checking counterparts, and do not hard code these boundaries. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
Cleans up the code a bit by using the driver-specific e1e_rphy and e1e_wphy macros instead of the full function pointer variants. Fix a couple whitespace issue with two already existing calls to e1e_wphy. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bruce Allan 提交于
The ICR register is clear on read and we don't care what the returned value is when resetting the hardware so the icr variable(s) can be removed. We should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and from e1000_get_phy_id_82571() (dump a debug message when it fails and when an unknown Phy id is returned). Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesse Gross 提交于
Now that there is a single function that can compute the device features relevant to a packet, we don't want to run it for each offload. This converts netif_needs_gso() to take the features of the device, rather than computing them itself. Signed-off-by: NJesse Gross <jesse@nicira.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 françois romieu 提交于
It workarounds the 60s firmware load failure timeout for the non-modular case. Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rafael J. Wysocki 提交于
The forcedeth driver uses the legacy PCI power management, so it has to do PCI-specific things in its ->suspend() and ->resume() callbacks and some of them are not done correctly. Convert forcedeth to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions. Tested with nVidia Corporation MCP55 Ethernet (rev a2). Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
This converts sky2 to new VLAN offload flags control via ethtool. It also allows for transmit offload of vlan tagged frames which was not possible before. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Reviewed-by: NJesse Gross <jesse@nicira.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
The sky2 driver would always try all possible supported speeds even if the user only asked for a limited set of speed/duplex combinations. Reported-by: NMohsen Hariri <m.hariri@gmail.com> Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladislav Zolotarov 提交于
Fix the race on bp->stats_pending between the timer and a LINK_UP event handler. Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladislav Zolotarov 提交于
Move to D0 before clearing MSI/MSI-X configuration. Otherwise MSI/MSI-X won't be cleared. Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladislav Zolotarov 提交于
Fixes in registers dump: - Properly calculate dump length for 57712. - Prevent HW blocks parity attentions when dumping registers in order to prevent false parity errors handling. - Update the bnx2x_dump.h file: old one had a few bugs that could cause fatal HW error as a result of a registers dump. Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladislav Zolotarov 提交于
Don't prevent RSS configuration in INT#x and MSI interrupt modes. Otherwise Rx hash key won't be available. Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesper Juhl 提交于
Failure to release_firmware() in drivers/net/hamradio/yam.c::add_mcs() causes memory leak. This patch should fix it. Signed-off-by: NJesper Juhl <jj@chaosbits.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shawn Guo 提交于
This patch is to add mx28 dual fec support. Here are some key notes for mx28 fec controller. - The mx28 fec controller naming ENET-MAC is a different IP from FEC used on other i.mx variants. But they are basically compatible on software interface, so it's possible to share the same driver. - ENET-MAC design on mx28 made an improper assumption that it runs on a big-endian system. As the result, driver has to swap every frame going to and coming from the controller. - The external phys can only be configured by fec0, which means fec1 can not work independently and both phys need to be configured by mii_bus attached on fec0. - ENET-MAC reset will get mac address registers reset too. - ENET-MAC MII/RMII mode and 10M/100M speed are configured differently FEC. - ETHER_EN bit must be set to get ENET-MAC interrupt work. Signed-off-by: NShawn Guo <shawn.guo@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shawn Guo 提交于
The following commit made a fix to use fec_enet_open/fec_enet_close over fec_enet_init/fec_stop for suspend/resume, because fec_enet_init does not allow to have a working network interface at resume. e3fe8558 net/fec: fix pm to survive to suspend/resume This fix works for i.mx/mxc fec controller, but fails on mx28 fec which gets a different interrupt logic design. On i.mx fec, interrupt can be triggered even bit ETHER_EN of ECR register is not set. But on mx28 fec, ETHER_EN must be set to get interrupt work. Meanwhile, MII interrupt is mandatory to resume the driver, because MDIO read/write changed to interrupt mode by commit below. 97b72e43 fec: use interrupt for MDIO completion indication fec_restart/fec_stop comes out as the solution working for both cases. Signed-off-by: NShawn Guo <shawn.guo@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shawn Guo 提交于
Add mac field into fec_platform_data and consolidate function fec_get_mac to get mac address in following order. 1) module parameter via kernel command line fec.macaddr=0x00,0x04,... 2) from flash in case of CONFIG_M5272 or fec_platform_data mac field for others, which typically have mac stored in fuse 3) fec mac address registers set by bootloader Signed-off-by: NShawn Guo <shawn.guo@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shawn Guo 提交于
The "index" becomes legacy since fep->pdev->id starts working to identify the instance. Moreover, the call of fec_enet_init(ndev, 0) always passes 0 to fep->index. This makes the following code in fec_get_mac buggy. /* Adjust MAC if using default MAC address */ if (iap == fec_mac_default) dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index; It may be the time to remove "index" and use fep->pdev->id instead. Signed-off-by: NShawn Guo <shawn.guo@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shawn Guo 提交于
FEC_MMFR_OP_WRITE should be used than FEC_MMFR_OP_READ in a mdio write operation. It's probably a typo introduced by commit: e6b043d5 netdev/fec.c: add phylib supporting to enable carrier detection (v2) Signed-off-by: NShawn Guo <shawn.guo@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 1月, 2011 6 次提交
-
-
由 Richard Mortimer 提交于
Fallback on the local-mac-address prom property if the Cassini device does not have an address programmed in the VPD ROM. This uses the same technique as implemented by the sungem driver. The problem was reported by Frans van Berckel using Debian kernel 2.6.34-7 on Sun Fire V440. udev was assigning a new eth<n> device name on each reboot because the cassini driver was using a random MAC address. Fix tested on 2.6.34-7 and 2.6.37 Sun Fire V440. Compile tested against 2.6.36 davem/sparc-2.6.git Reported-by: NFrans van Berckel <fberckel@xs4all.nl> Tested-by: NFrans van Berckel <fberckel@xs4all.nl> Reviewed-by: NJulian Calaby <julian.calaby@gmail.com> Reviewed-by: NSam Ravnborg <sam@ravnborg.org> Signed-off-by: NRichard Mortimer <richm@oldelvet.org.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ferenc Wagner 提交于
Signed-off-by: NFerenc Wagner <wferi@niif.hu> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ferenc Wagner 提交于
Signed-off-by: NFerenc Wagner <wferi@niif.hu> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The new firmware interface requires each Slow Path Queue (SPQ) message's type field to include the function number. The existing code does not do this consistently. We fix this by OR'ing in the function number into the type field centrally in cnic_submit_kwqe_16(). Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Axel Lin 提交于
Return -ENOMEM instead of 0 for the case of mdiobus_alloc and kmalloc failure. Signed-off-by: NAxel Lin <axel.lin@gmail.com> Acked-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Axel Lin 提交于
Return PTR_ERR(port->phydev) instead of 1 if phy_connect failed. Signed-off-by: NAxel Lin <axel.lin@gmail.com> Acked-by: NKrzysztof Halasa <khc@pm.waw.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-