Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

...as required by IB Spec, C10-29.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch enables IPoIB to use 4K UD messages (when the underlying
device and fabrics support a 4K MTU) by using two scatter buffers when
PAGE_SIZE is less than or equal to thhe HCA IB MTU size.  The first
buffer is for IPoIB header + GRH header, and the second buffer is the
IPoIB payload, which is 4K-4.
Signed-off-by: NShirley Ma <xma@us.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

After PXE boot, the iw_nes driver does a full reset to ensure the card
is in a clean state.  However, it doesn't wait for firmware to
complete its work before issuing a port reset to enable the ports,
which leads to problems bringing up the ports.

The solution is to wait for firmware to complete its work before
proceeding with port reset.

This bug was flagged by Roland Dreier <rolandd@cisco.com>.

Cc: <stable@kernel.org>
Signed-off-by: NChien Tung <ctung@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Use NIPQUAD_FMT instead of printing raw 32-bit hex quantities in
debugging output.
Acked-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Removing open-coded MAC formats shrinks the source and the generated
code too, eg on x86-64:

add/remove: 0/0 grow/shrink: 0/4 up/down: 0/-103 (-103)
function                                     old     new   delta
make_cm_node                                 932     912     -20
nes_netdev_set_mac_address                   427     406     -21
nes_netdev_set_multicast_list               1148    1124     -24
nes_probe                                   2349    2311     -38
Acked-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Match what the PCI specification uses.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The PCI MSI interface is stubbed out properly so that all the
functions just return failure if PCI_MSI=n, so there's no reason to
have "#ifdef CONFIG_PCI_MSI" blocks in ipath_iba7220.c.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Before IBA7220 support was added, the ipath driver didn't support any
hardware unless PCI_MSI and/or HT_IRQ was enabled.  However, the
IBA7220 can generate INTx interrupts, so it makes sense to allow the
driver to be build even if PCI_MSI=n and HT_IRQ=n.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The new IBA7220 code added a call to ipath_init_iba7220_funcs() that
is compiled unconditionally, but only built the IBA7220 code if
PCI_MSI is enabled.  Fix this by building the IBA7220 file
unconditonally.

This fixes build breakage when PCI_MSI=n, HT_IRQ=y and
INFINIBAND_IPATH=y reported by Ingo Molnar <mingo@elte.hu>:

 drivers/built-in.o: In function `ipath_init_one':
 ipath_driver.c:(.devinit.text+0x1e5bc): undefined reference to `ipath_init_iba7220_funcs'
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

IB/ipath: Remove reference to dev->class_dev                                                        
                                                                                                    
Commit 124b4dcb ("IB/ipath: add calls to new 7220 code and enable in                                
build") inadvertently added core to set dev->class_dev.dev back into                                
ib_ipath.  This is completely redundant since commit 1912ffbb ("IB: Set                             
class_dev->dev in core for nice device symlink"), which removed                                     
class_dev setting from low-level drivers, and also will break the build
when class_dev is removed completely from struct ib_device.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Describe disable_sma parameter with its name rather than the internal
ib_ipath_disable_sma variable name, so that the description shows up
properly in modinfo.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove redundant static declarations of functions that are defined
before they are used in the source.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/md/*.[ch] contains only one more printk line with a trailing space.
Remove it.
Signed-off-by: NNick Andrew <nick@nick-andrew.net>
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>

Spelling fixes for dmaengine.[ch]
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* Fix oops on cciss rmmod due to calling pci_free_consistent with
  irqs disabled.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Fix race condition between cciss_init_one(), cciss_update_drive_info(),
and cciss_check_queues().
Signed-off-by: NStephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

blk_rq_map_user adjusts bi_size of the last bio. It breaks the rule
that req->data_len (the true data length) is equal to sum(bio). It
broke the scsi command completion code.

commit e97a294e was introduced to fix
the above issue. However, the partial completion code doesn't work
with it. The commit is also a layer violation (scsi mid-layer should
not know about the block layer's padding).

This patch moves the padding adjustment to blk_rq_map_sg (suggested by
James). The padding works like the drain buffer. This patch breaks the
rule that req->data_len is equal to sum(sg), however, the drain buffer
already broke it. So this patch just restores the rule that
req->data_len is equal to sub(bio) without breaking anything new.

Now when a low level driver needs padding, blk_rq_map_user and
blk_rq_map_user_iov guarantee there's enough room for padding.
blk_rq_map_sg can safely extend the last entry of a scatter list.

blk_rq_map_sg must extend the last entry of a scatter list only for a
request that got through bio_copy_user_iov. This patches introduces
new REQ_COPY_USER flag.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch allows to use loop device with partitionned disk image.

Original behavior of loop is not modified.

A new parameter is introduced to define how many partition we want to be
able to manage per loop device. This parameter is "max_part".

For instance, to manage 63 partitions / loop device, we will do:
# modprobe loop max_part=63
# ls -l /dev/loop?*
brw-rw---- 1 root disk 7,   0 2008-03-05 14:55 /dev/loop0
brw-rw---- 1 root disk 7,  64 2008-03-05 14:55 /dev/loop1
brw-rw---- 1 root disk 7, 128 2008-03-05 14:55 /dev/loop2
brw-rw---- 1 root disk 7, 192 2008-03-05 14:55 /dev/loop3
brw-rw---- 1 root disk 7, 256 2008-03-05 14:55 /dev/loop4
brw-rw---- 1 root disk 7, 320 2008-03-05 14:55 /dev/loop5
brw-rw---- 1 root disk 7, 384 2008-03-05 14:55 /dev/loop6
brw-rw---- 1 root disk 7, 448 2008-03-05 14:55 /dev/loop7

And to attach a raw partitionned disk image, the original losetup is used:

# losetup -f etch.img
# ls -l /dev/loop?*
brw-rw---- 1 root disk 7,   0 2008-03-05 14:55 /dev/loop0
brw-rw---- 1 root disk 7,   1 2008-03-05 14:57 /dev/loop0p1
brw-rw---- 1 root disk 7,   2 2008-03-05 14:57 /dev/loop0p2
brw-rw---- 1 root disk 7,   5 2008-03-05 14:57 /dev/loop0p5
brw-rw---- 1 root disk 7,  64 2008-03-05 14:55 /dev/loop1
brw-rw---- 1 root disk 7, 128 2008-03-05 14:55 /dev/loop2
brw-rw---- 1 root disk 7, 192 2008-03-05 14:55 /dev/loop3
brw-rw---- 1 root disk 7, 256 2008-03-05 14:55 /dev/loop4
brw-rw---- 1 root disk 7, 320 2008-03-05 14:55 /dev/loop5
brw-rw---- 1 root disk 7, 384 2008-03-05 14:55 /dev/loop6
brw-rw---- 1 root disk 7, 448 2008-03-05 14:55 /dev/loop7
# mount /dev/loop0p1 /mnt
# ls /mnt
bench  cdrom  home        lib         mnt   root     srv  usr
bin    dev    initrd      lost+found  opt   sbin     sys  var
boot   etc    initrd.img  media       proc  selinux  tmp  vmlinuz
# umount /mnt
# losetup -d /dev/loop0

Of course, the same behavior can be done using kpartx on a loop device,
but modifying loop avoids to stack several layers of block device (loop +
device mapper), this is a very light modification (40% of modifications
are to manage the new parameter).
Signed-off-by: NLaurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

If cdrom commands are issued to a scsi drive in most cases the buffer will be
filled via dma.  This leads to bad stack corruption on non coherent platforms,
because the buffers are neither cache line aligned nor is the size a multiple
of the cache line size.  Using kmalloced buffers avoids this.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Now unregister_cdrom() always returns 0.
Make it return void and update all callers that check the return value.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Use list_head for cdrom_device_info list instead of opencoded
singly list handling.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch protects the list of cdrom_device_info by cdrom_mutex
when the file in /proc/sys/dev/cdrom/ is written.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch eliminates hardcoded return value of register_cdrom().

It also changes the return value to -EINVAL.
It is more appropriate than -2 (-ENOENT) because it is only
happen invalid usage of register_cdrom() by broken cdrom driver.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch removes #ifdef for CONFIG_SYSCTL by defining empty
cdrom_sysctl_register and cdrom_sysctl_unregister when CONFIG_SYSCTL
is not defined.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The following patch is an update to use an array instead of a list of
IOVA's in the implementation of defered iotlb flushes.  It takes
inspiration from sba_iommu.c

I like this implementation better as it encapsulates the batch process
within intel-iommu.c, and no longer touches iova.h (which is shared)

Performance data:  Netperf 32byte UDP streaming
2.6.25-rc3-mm1:
IOMMU-strict : 58Mps @ 62% cpu
NO-IOMMU : 71Mbs @ 41% cpu
List-based IOMMU-default-batched-IOTLB flush: 66Mbps @ 57% cpu

with this patch:
IOMMU-strict : 73Mps @ 75% cpu
NO-IOMMU : 74Mbs @ 42% cpu
Array-based IOMMU-default-batched-IOTLB flush: 72Mbps @ 62% cpu

Signed-off-by: <mgross@linux.intel.com>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

WARNING: drivers/pci/built-in.o(.text+0x28ee9): Section mismatch in reference from the function pci_bus_assign_resources() to the function .devinit.text:pci_setup_bridge()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

WARNING: drivers/pci/built-in.o(.text+0x28e1f): Section mismatch in reference from the function pci_bus_size_bridges() to the function .devinit.text:pci_bus_size_cardbus()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

WARNING: drivers/pci/built-in.o(.text+0x150f): Section mismatch in reference from the function pci_scan_single_device() to the function .devinit.text:pci_scan_device()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

WARNING: drivers/pci/built-in.o(.text+0xc4c): Section mismatch in reference from the function pci_add_new_bus() to the function .devinit.text:pci_alloc_child_bus()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The 'power' attribute of the fakephp driver originally only let one turn a
slot off.  If one tried to turn a slot on (echo 1 > .../power), it would
return ENODEV, as fakephp did not support this function.

An old (pre-git) patch changed this:
2004/11/11 16:33:31-08:00 jdittmer
[PATCH] fakephp: add pci bus rescan ability
http://article.gmane.org/gmane.linux.kernel/251183

Now writing "1" to the power attribute has the effect of triggering a bus
rescan, but it still returns ENODEV, probably an oversight in the above
patch.

Using the BusyBox echo will not produce an error message, but will
trigger *two* bus rescans (and return an exit code of 1):
~ # strace echo -n 1 > /sys/bus/pci/slots/0000:00:00.0/power
...
write(1, "1", 1)                        = -1 ENODEV (No such device)
write(1, "1", 1)                        = -1 ENODEV (No such device)
exit(1)                                 = ?

Using cp gives a write error, even though the write did happen and a rescan
was triggered:
~ # echo -n 1 > tmp ; cp tmp /sys/bus/pci/slots/0000:00:00.0/power
cp: Write Error: No such device

It seems much better to return success instead of failure.  The actual
status of the bus rescan is hard to return.  It happens asynchronously in a
work thread, so the sysfs store functions returns before any status is
ready (the whole point of the work queue).  And even if it didn't do this,
the rescan doesn't have any clear status to return.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
CC: Jan Dittmer <jdittmer@ppp0.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>