Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Fix for kernel panic when driver loads with HBA connected to non LUN 0 configured expander

With some enclosures when LUN 0 is not created but LUN 1 or LUN X is created
then SCSI scan procedure calls target_alloc, slave_alloc call back functions
for LUN 0 and slave_destory() for same LUN 0.

In these kind of cases within slave_destroy, pointer to scsi_target in
_sas_device structure is set to NULL, following which when slave_alloc for
LUN 1 is called then starget would not be set properly for this LUN.
So, scsi_target pointer pointing to NULL value would lead to a crash later
in the discovery procedure.

To solve this issue set the sas_device's scsi_target pointer to scsi_device's
scsi_target if it is NULL earlier in slave_alloc callback function.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: when Async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed

When Async scanning mode is enabled and device scanning is in progress then
devices should not be removed. But in actuality, devices are removed but
their transport layer entries are not removed. This causes error to add
the same device to the transport layer after host reset or diagnostic
reset.

So, in this patch, modified the code in such a way that device is not removed
when Async scanning mode is enabled and device scanning is in progress.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Infinite loop can occur if IOCStatus is not equal to
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value in the while loops in functions
_scsih_search_responding_sas_devices,
_scsih_search_responding_raid_devices and
_scsih_search_responding_expanders

So, Instead of checking for MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value,
in this patch code is modified to check for IOCStatus not equals to
MPI2_IOCSTATUS_SUCCESS to break the while loop.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The copyright in driver sources is updated for the year 2013.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Change set in MPI2 Rev x specification and 2.00.26 header files

1. Added two new AbortType values for TargetModeAbort Request: one to abort
   all IOs from a single initiator and other to abort only Command IUs.

2. Added Use Slot Information during Port Enable Event Reply flag to the Flags
   field of Manufacturing Page 7.

3. Added OEM Identifier to BiosOptions bits of BIOS Page 1.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The intent of this patch is to perform a graceful shutdown of target drives even if
volume doesn't exits. Changes done in this patch

1. Removed the check for the presence of volumes before sending down
   MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED. Therefore, this RAID action
   would be sent if the card is IR Firmware.

2. The MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED is sent even when the
   system undergoes suspend (in addition to remove/shutdown which was already
   present)
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Added a check to identify if mpi_reply is NULL in mpt2sas_ctl_event_callback()
and return without proceeding if it is the case.

Also modified the following functions to return void instead of 0 or 1
as returning those values from events perspective doesn't make sense.
* _base_async_event()
* mpt2sas_ctl_event_callback()
* mpt2sas_scsih_event_callback()
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

 section Signed-off-by: John Kacur <jkacur@redhat.com>

On a 3.6-rt (real-time patch) kernel we are seeing the following BUG
However, it appears to be relevant for non-realtime (mainline) as well.

[   49.688847] hpsa 0000:03:00.0: hpsa0: <0x323a> at IRQ 67 using DAC
[   49.749928] scsi0 : hpsa
[   49.784437] BUG: using smp_processor_id() in preemptible [00000000
00000000] code: kworker/u:0/6
[   49.784465] caller is enqueue_cmd_and_start_io+0x5a/0x100 [hpsa]
[   49.784468] Pid: 6, comm: kworker/u:0 Not tainted
3.6.11.5-rt37.52.el6rt.x86_64.debug #1
[   49.784471] Call Trace:
[   49.784512]  [<ffffffff812abe83>] debug_smp_processor_id+0x123/0x150
[   49.784520]  [<ffffffffa009043a>] enqueue_cmd_and_start_io+0x5a/0x100
[hpsa]
[   49.784529]  [<ffffffffa00905cb>]
hpsa_scsi_do_simple_cmd_core+0xeb/0x110 [hpsa]
[   49.784537]  [<ffffffff812b09c8>] ? swiotlb_dma_mapping_error+0x18/0x30
[   49.784544]  [<ffffffff812b09c8>] ? swiotlb_dma_mapping_error+0x18/0x30
[   49.784553]  [<ffffffffa0090701>]
hpsa_scsi_do_simple_cmd_with_retry+0x91/0x280 [hpsa]
[   49.784562]  [<ffffffffa0093558>]
hpsa_scsi_do_report_luns.clone.2+0xd8/0x130 [hpsa]
[   49.784571]  [<ffffffffa00935ea>]
hpsa_gather_lun_info.clone.3+0x3a/0x1a0 [hpsa]
[   49.784580]  [<ffffffffa00963df>] hpsa_update_scsi_devices+0x11f/0x4f0
[hpsa]
[   49.784592]  [<ffffffff81592019>] ? sub_preempt_count+0xa9/0xe0
[   49.784601]  [<ffffffffa00968ad>] hpsa_scan_start+0xfd/0x150 [hpsa]
[   49.784613]  [<ffffffff8158cba8>] ? rt_spin_lock_slowunlock+0x78/0x90
[   49.784626]  [<ffffffff813b04d7>] do_scsi_scan_host+0x37/0xa0
[   49.784632]  [<ffffffff813b05da>] do_scan_async+0x1a/0x30
[   49.784643]  [<ffffffff8107c4ab>] async_run_entry_fn+0x9b/0x1d0
[   49.784655]  [<ffffffff8106ae92>] process_one_work+0x1f2/0x620
[   49.784661]  [<ffffffff8106ae20>] ? process_one_work+0x180/0x620
[   49.784668]  [<ffffffff8106d4fe>] ? worker_thread+0x5e/0x3a0
[   49.784674]  [<ffffffff8107c410>] ? async_schedule+0x20/0x20
[   49.784681]  [<ffffffff8106d5d3>] worker_thread+0x133/0x3a0
[   49.784688]  [<ffffffff8106d4a0>] ? manage_workers+0x190/0x190
[   49.784696]  [<ffffffff81073236>] kthread+0xa6/0xb0
[   49.784707]  [<ffffffff815970a4>] kernel_thread_helper+0x4/0x10
[   49.784715]  [<ffffffff81082a7c>] ? finish_task_switch+0x8c/0x110
[   49.784721]  [<ffffffff8158e44b>] ? _raw_spin_unlock_irq+0x3b/0x70
[   49.784727]  [<ffffffff8158e85d>] ? retint_restore_args+0xe/0xe
[   49.784734]  [<ffffffff81073190>] ? kthreadd+0x1e0/0x1e0
[   49.784739]  [<ffffffff815970a0>] ? gs_change+0xb/0xb

-------------------

This is caused by
enqueue_cmd_and_start_io()->
        set_performant_mode()->
                smp_processor_id()
Which if you have debugging enabled calls debug_processor_id() and triggers the warning.

The code here is
 c->Header.ReplyQueue = smp_processor_id() % h->nreply_queues;

Since it is not critical that the code complete on the same processor,
but the cpu is a hint used in generating the ReplyQueue and will still work if
the cpu migrates or is preempted, it is safe to use the raw_smp_processor_id()
to surpress the false positve warning.
Signed-off-by: NJohn Kacur <jkacur@redhat.com>
Acked-by: NStephen Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

To run discovery over iSER we need to advertize the CAP_TEXT_NEGO capability
towards user space. Also need to make sure the login RX buffer is posted when
SendTargets TEXT PDUs are sent. For that end, we use a setting of the
ISCSI_PARAM_DISCOVERY_SESS iscsi param as an indication that this is
discovery session.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Acked-by: Nlindar_liu <lindar_liu@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: Anandkumar.Santhanam@pmcs.com
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If mpt3sas_base_map_resources takes an early error path then its
counterpart, mpt3sas_base_free_resources needs to be careful about
cleaning up:

  1 - _base_mask_interrupts and _base_make_ioc_ready require memory
      mapped I/O registers, make sure that this is true.

  2 - _base_free_irq iterates over the adapter's reply_queue_list, so
      move this list head initialization out of _base_enable_msix to
      _scsih_probe so this will always be safe.

  3 - check that the controller PCI device and its BARs have been
      enabled before disabling them.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If mpt2sas_base_map_resources takes an early error path then its
counterpart, mpt2sas_base_free_resources needs to be careful about
cleaning up:

  1 - _base_mask_interrupts and _base_make_ioc_ready require memory
      mapped I/O registers, make sure that this is true.

  2 - _base_free_irq iterates over the adapter's reply_queue_list, so
      move this list head initialization out of _base_enable_msix to
      _scsih_probe so this will always be safe.

  3 - check that the controller PCI device and its BARs have been
      enabled before disabling them.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Generate a uevent when the following Unit Attention ASC/ASCQ
codes are received:

    2A/01  MODE PARAMETERS CHANGED
    2A/09  CAPACITY DATA HAS CHANGED
    38/07  THIN PROVISIONING SOFT THRESHOLD REACHED
    3F/03  INQUIRY DATA HAS CHANGED
    3F/0E  REPORTED LUNS DATA HAS CHANGED

Log kernel messages when the following Unit Attention ASC/ASCQ
codes are received that are not as specific as those above:

    2A/xx  PARAMETERS CHANGED
    3F/xx  TARGET OPERATING CONDITIONS HAVE CHANGED

Added logic to set expecting_lun_change for other LUNs on the target
after REPORTED LUNS DATA HAS CHANGED is received, so that duplicate
uevents are not generated, and clear expecting_lun_change when a
REPORT LUNS command completes, in accordance with the SPC-3
specification regarding reporting of the 3F 0E ASC/ASCQ UA.

[jejb: remove SPC3 test in scsi_report_lun_change and some docbook fixes and
       unused variable fix, both reported by Fengguang Wu]
Signed-off-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add the appropriate definitions and table entries for new adapter support.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When the driver calls scsi_done and after that frees it's internal
preallocated memory it can happen that a new job is enqueud before
the memory is freed. The allocation fails and the message
"cmd_alloc returned NULL" is shown.
Patch below fixes it by moving cmd->scsi_done after cmd_free.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

It seems the "phy_index++;" have been placed in wrong place, without it
the while circle up will do a infinite loop.
Signed-off-by: NXinghai Yu <yuxinghai@cn.fujitsu.com>
Acked-by: NLukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

scsi_remove_host() sends SYNCHRONIZE CACHE commands for write cache
enabled scsi disk devices.  So stopping controller working shouldn't
be done before scsi_remove_host().
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When removing the UFS driver, disable_irq() is called and the IRQ is
not enabled again.  Unfortunately, the IRQ is requested with IRQF_SHARED
and it can be shared among several devices.  So disabling the IRQ in
this way is just breaking other devices which are sharing the IRQ.
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Before commit 2953f850 ("[SCSI] ufs:
use devres functions for ufshcd"), UFSHCI register was ioremapped by
each glue-driver (ufshcd-pltfrm and ufshcd-pci) during probing and it
was iounmapped by core-driver during removing driver.  The commit
converted ufshcd-pltfrm to use devres functions, but it didn't convert
ufshcd-pci.

Therefore, the change causes ufshcd-pci driver not to iounmap UFSHCI
register region during removing driver.  This fixes it by converting
ufshcd-pci to use devres functions.
Signed-off-by: NAkinobu Mita <mita@fixstars.com>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add runtime PM helpers to suspend/resume UFS controller at runtime.
Enable runtime PM by default for pci and platform drivers as the
initialized hardware can suspend if it is not used after bootup.
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Background operations in the UFS device can be disabled by
the host to reduce the response latency of transfer requests.
Add support for enabling/disabling the background operations
during runtime suspend/resume of the device.

If the device is in critical need of BKOPS it will raise an
URGENT_BKOPS exception which should be handled by the host to
make sure the device performs as expected.

During bootup, the BKOPS is enabled in the device by default.
The disable of BKOPS is supported only when the driver supports
runtime suspend/resume operations as the runtime PM framework
provides a way to determine the device idleness and hence BKOPS
can be managed effectively. During runtime resume the BKOPS is
disabled to reduce latency and during runtime suspend the BKOPS
is enabled to allow device to carry out idle time BKOPS.

In some cases where the BKOPS is disabled during runtime resume
and due to continuous data transfers the runtime suspend is not
triggered, the BKOPS is enabled when the device raises a level-2
exception (outstanding operations - performance impact).
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Allow UFS device to complete its initialization and accept
SCSI commands by setting fDeviceInit flag. The device may take
time for this operation and hence the host should poll until
fDeviceInit flag is toggled to zero. This step is mandated by
UFS device specification for device initialization completion.
Signed-off-by: NDolev Raviv <draviv@codeaurora.org>
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

As part of device initialization sequence, sending NOP OUT UPIU and
waiting for NOP IN UPIU response is mandatory. This confirms that the
device UFS Transport (UTP) layer is functional and the host can configure
the device with further commands. Add support for sending NOP OUT UPIU to
check the device connection path and test whether the UTP layer on the
device side is functional during initialization.

A tag is acquired from the SCSI tag map space in order to send the device
management command. When the tag is acquired by internal command the scsi
command is rejected with host busy flag in order to requeue the request.
To avoid frequent collisions between internal commands and scsi commands
the device management command tag is allocated in the opposite direction
w.r.t block layer tag allocation.
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NDolev Raviv <draviv@codeaurora.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Flash target index 0 and 1 are reserved for boot target entries created
with BIOS utility.
Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

While setting the values for DDB, discovery_parent_idx needs to be used
instead of discovery_parent_type.
Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If logout is performed on a failed session entry then that session
should be gracefully removed.
Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>