Based on a patch from: Amit Shah <amit.shah@qumranet.com>

This patch adds support for handling PCI devices that are assigned to
the guest.

The device to be assigned to the guest is registered in the host kernel
and interrupt delivery is handled.  If a device is already assigned, or
the device driver for it is still loaded on the host, the device
assignment is failed by conveying a -EBUSY reply to the userspace.

Devices that share their interrupt line are not supported at the moment.

By itself, this patch will not make devices work within the guest.
The VT-d extension is required to enable the device to perform DMA.
Another alternative is PVDMA.
Signed-off-by: NAmit Shah <amit.shah@qumranet.com>
Signed-off-by: NBen-Ami Yassour <benami@il.ibm.com>
Signed-off-by: NWeidong Han <weidong.han@intel.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

KVM intends to use paravirt code to calibrate khz. Xen
current code will do just fine. So as a first step, factor out
code to pvclock.c.
Signed-off-by: NGlauber Costa <gcosta@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This can be used by kvm subsystems that are interested in when
interrupts are acked, for example time drift compensation.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch adds a trace point for the instruction emulation on embedded powerpc
utilizing the KVM_TRACE interface.
Signed-off-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch adds trace points to track powerpc TLB activities using the
KVM_TRACE infrastructure.
Signed-off-by: NJerone Young <jyoung5@us.ibm.com>
Signed-off-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

The current kvmtrace code uses get_cycles() while the interpretation would be
easier using using nanoseconds. ktime_get() should give at least the same
accuracy as get_cycles on all architectures (even better on 32bit archs) but
at a better unit (e.g. comparable between hosts with different frequencies.

[avi: avoid ktime_t in public header]
Signed-off-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Acked-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch fixes kvmtrace use on big endian systems. When using bit fields the
compiler will lay data out in the wrong order expected when laid down into a
file.
This fixes it by using one variable instead of using bit fields.
Signed-off-by: NJerone Young <jyoung5@us.ibm.com>
Signed-off-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

As we execute real mode guests in VM86 mode, exception have to be
reinjected appropriately when the guest triggered them. For this purpose
the patch adopts the real-mode injection pattern used in vmx_inject_irq
to vmx_queue_exception, additionally taking care that the IP is set
correctly for #BP exceptions. Furthermore it extends
handle_rmode_exception to reinject all those exceptions that can be
raised in real mode.

This fixes the execution of himem.exe from FreeDOS and also makes its
debug.com work properly.

Note that guest debugging in real mode is broken now. This has to be
fixed by the scheduled debugging infrastructure rework (will be done
once base patches for QEMU have been accepted).
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

Similar to the exception queue, this hold interrupts that have been
accepted by the virtual processor core but not yet injected.

Not yet used.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

Instead of processing nmi injection failure in the vm entry path, move
it to the vm exit path (vm_complete_interrupts()).  This separates nmi
injection from nmi post-processing, and moves the nmi state from the VT
state into vcpu state (new variable nmi_injected specifying an injection
in progress).
Signed-off-by: NAvi Kivity <avi@qumranet.com>

Move KVM trace definitions from x86 specific kvm headers to common kvm
headers to create a cross-architecture numbering scheme for trace
events. This means the kvmtrace_format userspace tool won't need to know
which architecture produced the log file being processed.
Signed-off-by: NJerone Young <jyoung5@us.ibm.com>
Signed-off-by: NHollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

As suggested by Avi, introduce accessors to read/write guest registers.
This simplifies the ->cache_regs/->decache_regs interface, and improves
register caching which is important for VMX, where the cost of
vmcs_read/vmcs_write is significant.

[avi: fix warnings]
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

Commit 8006479c introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.

Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.

In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
Signed-off-by: NAnssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix hiddev.h example code.
To get the correct usage code, you need to set report_type and
report_id.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix mixed space and tabs in example code.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

hid-ff.c now calls only pidff (generic driver), the special ones are now
in separate drivers. Invoke pidff on all non-special directly.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move the force feedback processing into a separate module.

[jkosina@suse.cz: fix Kconfig texts a little bit]
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Merge the logitech force feedback processing directly into logitech
driver from the usbhid core.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move the handling of the leds resetting from the core to
the dell and logitech drivers.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Remove support for both dynamic and static report descriptor
quirks. There is no longer rdesc code which it would support,
so it's useless.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Remove the file since these is no user now.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move them from the core code to a separate driver.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add compat option to hid code to allow loading of all modules on
systems which don't allow autoloading because of old userspace.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move them from the core code to a separate driver.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move ignore quirks from usbhid-quirks into hid-core code. Also don't output
warning when ENODEV is error code in usbhid and try ordinal input in hidp
when that error is returned.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Move them from the core and input code to a separate driver.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This mapping are currently used on 2 placces and will be needed by more
quirk drivers, so move them to hid.h to allow them to use it.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>