Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

pvrusb2: Recognize and handle mode change before dealing with changes
related to the video standard.  Even though the video standard should
only matter when in analog mode, doing this way is technically cleaner
in case there's other stuff that might depend on both.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This tuner PLL has missing initialisation settings resulting in
haphazard tuning. The PLL LPF was set to just 22000 symbol rate.

Basically, the module is a Sharp BS2F7HZ0194 (STV0299+IX2410)

I have had problems implementing the PLL in a new driver and
did not want to break the IX2410 out of the PLL.

This applies to DW2102, DM1105, CX88 and OPERA1 drivers.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since the drivers/ieee1394/ backend was removed from firedtv, its I/O no
longer needs to be abstracted as exchangeable backend methods.

Also, ieee1394 variants of module and device probe and removal are no
longer there.  Move module probe and removal into firedtv-fw.c where
device probe and removal are implemented.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Don't allow everybody to change video settings.
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changes:
  Add function tm6000_set_reg_mask for change some bits in regs. Very usefull, simplify some code with this function.
  Add control mute
  Add control volume
  Add control audio input MUX
  Add support radio

Radio works well. TV works too

Known bugs:
  The programm gnomeradio can't set freq for radio, it use old v4l API. Audio over USB works via arecord.
  The programm mplayer can set freq but no any audio
           mplayer -v -rawaudio rate=48000 radio://105.2/capture driver=v4l2:alsa:adevice=hw.1,0:amode=1:audiorate=48000:forceaudio:immediatemode=0
  When start watch TV very shortly after radio the kernel crashed hardly. Didn't stop all USB URBs, need some time for stop.

[mchehab@redhat.com: fix merge conflicts]
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for Terratec Grabster AV 150/250 MX. For now it is
only possible to use composite input as switching inputs does not work.

[mchehab@redhat.com: Fix merge conflicts and simplify board entries]
Signed-off-by: NHolger Nelson <hnelson@hnelson.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add two new TV cards of Beholder.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Speed up tuning, as firmware is not necessary to load every attempt to tune
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Decrease firmware loading time. Before it is ~4000 i2c calls,
now it is ~256 i2c calls to load ds3000 firmware.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

TeVii s480 works fine with that on DVB-S2 channels
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make some initializations in init, not in tune function
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card.  The Nova-S-plus
has a WM8775 ADC that is currently not detected.  This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.

[mchehab@redhat.com: Changed the patch to only talk with wm8775 if board
info says so. Also, added platform_data support, to avoid changing the
behaviour for other boards, and fixed CodingStyle]

[awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion
bridge driver private and let the bridge driver set the value of
v4l2_subdev.grp_id.]

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>

Add one more radio input, usefull for tm6010
Add control output amplitude.
Add set_config function for configure tuner when TV card hasn't dvb part.
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add linux/sched.h because of missing declaration of TASK_NORMAL.

This patch fixes the following error:

drivers/media/video/omap24xxcam.c: In function
'omap24xxcam_vbq_complete':
drivers/media/video/omap24xxcam.c:415: error: 'TASK_NORMAL' undeclared
(first use in this function)
drivers/media/video/omap24xxcam.c:415: error: (Each undeclared
identifier is reported only once
drivers/media/video/omap24xxcam.c:415: error: for each function it
appears in.)
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing
	if (var == 0)
with
	if (!var)
after an allocation
and all other offending 0s with NULL.

KernelVersion: linus' tree-1f0324caSigned-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The cxhdl->priv field was not set initially, only after capturing started.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Acked-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It takes too long time to scan due to low symbol rate PID's
like PAT, PMT, CAT, NIT.
For that matter we enabled permanently all PID's
less 0x20 in hardware PID filter for NetUP Dual DVB-T/C CI RF card
to combine rates.
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is needed for multifrontend support.
NetUP Dual DVB-T/C CI RF card has frontends connected to port B & C
Each frontend has two switchable cores - DVB-T & DVB-C
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is two external I2C buses in cx23885 chip.
Currently, analog tuners supported for second I2C bus only
In NetUP Dual DVB-T/C CI RF card tuners connected to first bus
So, in order to support analog tuners sitting on first bus
we need modifications.
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The card based on cx23885 PCI-e brige. Altera FPGA for CI,
multistandard demods stv0367 from STM for QAM & OFDM,  Xcieve xc5000 tuners
and additional cx25840 for second analog input.
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The STV0367 is a multi-standard demodulator which is
capable of processing DVB-T as well as DVB-C signals.
It is fully compliant with DVB-T and DVB-C
recommendations for broadcast services.
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

An Altera FPGA CI module for NetUP Dual DVB-T/C RF CI card.
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It uses STAPL files and programs Altera FPGA through JTAG.
Interface to JTAG must be provided from main device module,
for example through cx23885 GPIO.
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing the offending 0s with NULL.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Reviewed-by: NDevin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This soc_camera driver is for Omnivision's OV9740 sensor.  This initial
submission provides support for YUV422 output at 1280x720 (720p), which is
the sensor's native resolution.  640x480 (VGA) is also supported, with
cropping and scaling performed by the sensor's ISP.

This driver is heavily based off of the existing OV9640 driver.
Signed-off-by: NAndrew Chew <achew@nvidia.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the correct scales to calculate cropping offsets.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now that soc-camera supports videobuf API v1 and v2, camera-host drivers
can be converted to videobuf2 individually. This patch converts the
mx3_camera driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert the sh_mobile_ceu_camera driver to the videobuf2 API.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add two helper inline functions to retrieve soc-camera device context
from videobuf and videobuf2 queue pointers.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Extend soc-camera core to also support the videobuf2 API.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

videobuf2-memops and videobuf2-core can be compiled as modules, in which
case 3 more symbols from videobuf2-memops.c have to be exported.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If the camera was set to output formats like RGB565 YUYV or SBGGR10,
the resulting image was scrambled due to erroneous interpretations of
horizontal parameter's units.

This patch in fourcc_to_ipu_pix, eliminate also the pixel formats mappings
that, first are not used within mainline code and second, standing at
the datasheets, they will not work properly:

The IPU internal bus support only the following data formatting
(44.1.1.3 Data Flows and Formats):
 1 YUV 4:4:4 or RGB-8 bits per color component
 2 YUV 4:4:4 or RGB-10 bits per color component
 3 Generic data (from sensor to the system memory only)

And format conversions are done:
 - from memory: unpacking from other formats to IPU supported ones
 - to memory: packing in the inverse order.

So, assigning a packing/unpacking strategy to the IPU for those formats
will produce a packing to memory and not the inverse.
Signed-off-by: NAlberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The 'pix->width' field may be updated in mx3_camera_set_fmt() to
fulfill the IPU stride line alignment requirements. If this update
takes place, the 'fmt.pix.sizeimage' field in the struct v4l2_format
stucture returned by VIDIOC_S_FMT is wrong. We need to update the
'pix->sizeimage' field in the mx3_camera_set_fmt() function to fix
this issue.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Even though clk_put() is a no-op on most architectures it is not for
some ARM implementations. To not fail on those, release the clock timer
before freeing the surrounding structure.

This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a function to calculate the number of samples on the media-bus,
required to retrieve one pixel of a certain format.
Signed-off-by: NAlberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some camera systems have strong requirement for capturing
an exact number of frames after starting the stream and do
not tolerate losing captured frames. By starting the stream
after the videobuf has queued the buffers, we ensure that
no frame will be lost.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>