- 25 3月, 2008 12 次提交
-
-
由 Jeff Garzik 提交于
At least one report claims that a878539e failed to solve lockups, whereas the old limit-to-32-bit trick worked. Restore the 32-bit limit, but also leave the 255-sector limit in place, because we know that's needed as well. Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
-
由 Mikael Pettersson 提交于
A Promise SATA controller will signal hotplug events when a hard reset (COMRESET) is done on a port. These events aren't masked by the driver, and the unexpected interrupts will cause a sequence of failed reset attempts util libata's EH finally gives up. This has not been a common problem so far, but the pending libata hardreset-by-default changes makes it a critical issue. The solution is to disable hotplug events before a reset, and to reenable them afterwards. (Promise's driver does this too.) This patch adds SATA-specific versions of ->freeze() and ->thaw() that also disable and enable hotplug events. PATA ports continue to use the old versions of ->freeze() and ->thaw(). Accesses to the hotplug register must be serialised via host->lock. We rely on ap->lock == &ap->host->lock and that libata takes this lock before ->freeze() and ->thaw(). Document this requirement. The interrupt handler is adjusted so its hotplug register accesses are inside the region protected by host->lock. Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4, FastTrack TX4000) with various combinations of SATA and PATA disks, with and without the pending hardreset-by-default changes. Signed-off-by: NMikael Pettersson <mikpe@it.uu.se> Acked-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
There's no point in retrying and eventually failing device detection when the device rejects READ_NATIVE_MAX[_EXT]. Disable HPA unlocking if READ_NATIVE_MAX[_EXT] is rejected as done when SET_MAX[_EXT] is rejected. This allows some old drives to work even if they aren't blacklisted. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
This is to fix bugzilla #10254. QSI cdrom attached to pata_sis as secondary master appears as phantom device for the slave. Interestingly, instead of not setting DRQ after IDENTIFY which triggers NODEV_HINT, it aborts both IDENTIFY and IDENTIFY PACKET which makes EH retry. Modify EH such that it assumes no device is attached if both flavors of IDENTIFY are aborted by the device. There really isn't much point in retrying when the device actively aborts the commands. While at it, convert NODEV detection message to ata_dev_printk() to help debugging obscure detection problems. This problem was reported by Jan Bücken. Signed-off-by: NTejun Heo <htejun@gmail.com> Cc: Jan Bücken <jb.faq@gmx.de> Acked-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
pata_it821x needs to look at raw request size in check_atapi_dma(). Signed-off-by: NTejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
Implement ata_qc_raw_nbytes() which determines the raw user-requested size of a PC command. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc由 Linus Torvalds 提交于
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [POWERPC] Fix Oops with TQM5200 on TQM5200 [POWERPC] mpc5200: Fix null dereference if bestcomm fails to initialize [POWERPC] mpc5200-fec: Fix possible NULL dereference in mdio driver [POWERPC] Fix crash in init_ipic_sysfs on efika [POWERPC] Don't use 64k pages for ioremap on pSeries
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: [SPARC64]: exec PT_DTRACE [SPARC64]: Use shorter list_splice_init() for brevity. [SPARC64]: Remove most limitations to kernel image size.
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: sch_htb: fix "too many events" situation connector: convert to single-threaded workqueue [ATM]: When proc_create() fails, do some error handling work and return -ENOMEM. [SUNGEM]: Fix NAPI assertion failure. BNX2X: prevent ethtool from setting port type [9P] net/9p/trans_fd.c: remove unused variable [IPV6] net/ipv6/ndisc.c: remove unused variable [IPV4] fib_trie: fix warning from rcu_assign_poinger [TCP]: Let skbs grow over a page on fast peers [DLCI]: Fix tiny race between module unload and sock_ioctl. [SCTP]: Fix build warnings with IPV6 disabled. [IPV4]: Fix null dereference in ip_defrag
-
由 Roland Dreier 提交于
The iWARP protocol limits RDMA read requests to a single scatter entry. NFS/RDMA has code in rdma_read_max_sge() that is supposed to limit the sge_count for RDMA read requests to 1, but the code to do that is inside an #ifdef RDMA_TRANSPORT_IWARP block. In the mainline kernel at least, RDMA_TRANSPORT_IWARP is an enum and not a preprocessor #define, so the #ifdef'ed code is never compiled. In my test of a kernel build with -j8 on an NFS/RDMA mount, this problem eventually leads to trouble starting with: svcrdma: Error posting send = -22 svcrdma : RDMA_READ error = -22 and things go downhill from there. The trivial fix is to delete the #ifdef guard. The check seems to be a remnant of when the NFS/RDMA code was not merged and needed to compile against multiple kernel versions, although I don't think it ever worked as intended. In any case now that the code is upstream there's no need to test whether the RDMA_TRANSPORT_IWARP constant is defined or not. Without this patch, my kernel build on an NFS/RDMA mount using NetEffect adapters quickly and 100% reproducibly failed with an error like: ld: final link failed: Software caused connection abort With the patch applied I was able to complete a kernel build on the same setup. (Tom Tucker says this is "actually an _ancient_ remnant when it had to compile against iWARP vs. non-iWARP enabled OFA trees.") Signed-off-by: NRoland Dreier <rolandd@cisco.com> Acked-by: NTom Tucker <tom@opengridcomputing.com> Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
It appears that 64-bit PCI resources cannot possibly ever have worked on x86-32 even when the RESOURCES_64BIT config option was set, because any driver that tried to [pci_]ioremap() the resource would have been unable to do so because the high 32 bits would have been silently dropped on the floor by the ioremap() routines that only used "unsigned long". Change them to use "resource_size_t" instead, which properly encodes the whole 64-bit resource data if RESOURCES_64BIT is enabled. Acked-by: NH. Peter Anvin <hpa@kernel.org> Acked-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
The printk() can deadlock because it can wake up klogd(), and task enqueueing will try to read the time in order to set a hrtimer. Reported-by: NMarcin Slusarz <marcin.slusarz@gmail.com> Debugged-by: NPeter Zijlstra <a.p.zijlstra@chello.nl> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 24 3月, 2008 10 次提交
-
-
由 Anatolij Gustschin 提交于
The "bestcomm-core" driver defines its of_match table as follows static struct of_device_id mpc52xx_bcom_of_match[] = { { .type = "dma-controller", .compatible = "fsl,mpc5200-bestcomm", }, { .type = "dma-controller", .compatible = "mpc5200-bestcomm", }, {}, }; so while registering the driver, the driver's probe function won't be called, because the device tree node doesn't have a device_type property. Thus the driver's bcom_engine structure won't be allocated. Referencing this structure later causes observed Oops. Checking bcom_eng pointer for NULL before referencing data pointed by it prevents oopsing, but fec driver still doesn't work (because of the lost bestcomm match and resulted task allocation failure). Actually the compatible property exists and should match and so the fec driver should work. This removes .type = "dma-controller" from the bestcomm driver's mpc52xx_bcom_of_match table to solve the problem. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Grant Likely 提交于
If the bestcomm initialization fails, calls to the task allocate function should fail gracefully instead of oopsing with a NULL deref. Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Grant Likely 提交于
If the reg property is missing from the phy node (unlikely, but possible), then the kernel will oops with a NULL pointer dereference. This fixes it by checking the pointer first. Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Olaf Hering 提交于
The global primary_ipic in arch/powerpc/sysdev/ipic.c can remain NULL if ipic_init() fails, which will happen on machines that don't have an ipic interrupt controller. init_ipic_sysfs() will crash in that case. Acked-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Paul Mackerras 提交于
On pSeries, the hypervisor doesn't let us map in the eHEA ethernet adapter using 64k pages, and thus the ehea driver will fail if 64k pages are configured. This works around the problem by always using 4k pages for ioremap on pSeries (but not on other platforms). A better fix would be to check whether the partition could ever have an eHEA adapter, and only force 4k pages if it could, but this will do for 2.6.25. This is based on an earlier patch by Tony Breeds. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Roland McGrath 提交于
The PT_DTRACE flag is meaningless and obsolete. Don't touch it. Signed-off-by: NRoland McGrath <roland@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Robert P. J. Day 提交于
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Martin Devera 提交于
HTB is event driven algorithm and part of its work is to apply scheduled events at proper times. It tried to defend itself from livelock by processing only limited number of events per dequeue. Because of faster computers some users already hit this hardcoded limit. This patch limits processing up to 2 jiffies (why not 1 jiffie ? because it might stop prematurely when only fraction of jiffie remains). Signed-off-by: NMartin Devera <devik@cdi.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Evgeniy Polyakov 提交于
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru> We don't need one cqueue thread for each CPU. cqueue is used for receiving userspace datagrams, which are very rare and thus will happily live with a single queue. Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wang Chen 提交于
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 3月, 2008 16 次提交
-
-
由 David S. Miller 提交于
As reported by Johannes Berg: I started getting this warning with recent kernels: [ 773.908927] ------------[ cut here ]------------ [ 773.908954] Badness at net/core/dev.c:2204 ... If we loop more than once in gem_poll(), we'll use more than the real budget in our gem_rx() calls, thus eventually trigger the caller's assertions in net_rx_action(). Subtract "work_done" from "budget" for the second arg to gem_rx() to fix the bug. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eliezer Tamir 提交于
On 10GBaseT boards setting the type to TP will cause the driver to try to configure 1GBaseT. Since there are currently no boards that support setting of the port type, disable this for now. Signed-off-by: NEliezer Tamir <eliezert@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julia Lawall 提交于
The variable cb is initialized but never used otherwise. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ type T; identifier i; constant C; @@ ( extern T i; | - T i; <+... when != i - i = C; ...+> ) // </smpl> Signed-off-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julia Lawall 提交于
The variable hlen is initialized but never used otherwise. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ type T; identifier i; constant C; @@ ( extern T i; | - T i; <+... when != i - i = C; ...+> ) // </smpl> Signed-off-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
This gets rid of a warning caused by the test in rcu_assign_pointer. I tried to fix rcu_assign_pointer, but that devolved into a long set of discussions about doing it right that came to no real solution. Since the test in rcu_assign_pointer for constant NULL would never succeed in fib_trie, just open code instead. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: RDMA/nes: Fix MSS calculation on RDMA path
-
git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: Revert "ide-tape: schedule driver for removal after 6 months" ide: mark "hdx=remap" and "hdx=remap63" kernel parameters as obsoleted ide: mark "hdx=[driver_name]" and "hdx=scsi" kernel parameters as obsoleted ide: Documentation/ide/ide.txt fixes ide: mark special "ide0=" kernel parameters as obsoleted ide: remove commented out entries from ide_pio_blacklist[]
-
git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: [CIFS] Fix mem leak on dfs referral [CIFS] file create with acl support enabled is slow [CIFS] Fix mtime on cp -p when file data cached but written out too late [CIFS] Fix build problem [CIFS] cifs: replace remaining __FUNCTION__ occurrences [CIFS] DFS patch that connects inode with dfs handling ops
-
git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: x86: revert: reserve dma32 early for gart
-
由 Hans Rosenfeld 提交于
Change pagemap output format to allow for future reporting of huge pages. (Format comment and minor cleanups: mpm@selenic.com) Signed-off-by: NHans Rosenfeld <hans.rosenfeld@amd.com> Signed-off-by: NMatt Mackall <mpm@selenic.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Pierre Ossman 提交于
Suppressing uevents turned out to be a bad idea as it screws up the order of events, making user space very confused. Change the system to use sysfs groups instead. This is a regression that, for some odd reason, has gone unnoticed for some time. It confuses hal so that the block devices (which have the mmc device as a parent) are not registered. End result being that desktop magic when cards are inserted won't work. Signed-off-by: NPierre Ossman <drzeus@drzeus.cx> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Darren Salt 提交于
Increase the number of PnP memory resources from 12 to 24. This removes an "exceeded the max num of mem resources" warning on boot. I also noticed the reservation of two more iomem ranges on the computer on which this was tested. Signed-off-by: NDarren Salt <linux@youmustbejoking.demon.co.uk> Signed-off-by: NIngo Molnar <mingo@elte.hu> Acked-by: NBjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Bjorn Helgaas 提交于
PNP_MAX_MEM and PNP_MAX_PORT are mainly used to size tables of PNP device resources. In 2.6.24, we increased their values to accomodate ACPI devices that have many resources: 2.6.23 2.6.24 ------ ------ PNP_MAX_MEM 4 12 PNP_MAX_PORT 8 40 However, ISAPNP also used these constants as the size of parts of the logical device register set. This register set is fixed by hardware, so increasing the constants meant that we were reading and writing unintended parts of the register set. This patch changes ISAPNP to use the correct register set sizes (the same values we used prior to 2.6.24). Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Steve French 提交于
Signed-off-by: NIgor Mammedov <niallain@gmail.com> Signed-off-by: NSteve French <sfrench@us.ibm.com>
-
由 Herbert Xu 提交于
While testing the virtio-net driver on KVM with TSO I noticed that TSO performance with a 1500 MTU is significantly worse compared to the performance of non-TSO with a 16436 MTU. The packet dump shows that most of the packets sent are smaller than a page. Looking at the code this actually is quite obvious as it always stop extending the packet if it's the first packet yet to be sent and if it's larger than the MSS. Since each extension is bound by the page size, this means that (given a 1500 MTU) we're very unlikely to construct packets greater than a page, provided that the receiver and the path is fast enough so that packets can always be sent immediately. The fix is also quite obvious. The push calls inside the loop is just an optimisation so that we don't end up doing all the sending at the end of the loop. Therefore there is no specific reason why it has to do so at MSS boundaries. For TSO, the most natural extension of this optimisation is to do the pushing once the skb exceeds the TSO size goal. This is what the patch does and testing with KVM shows that the TSO performance with a 1500 MTU easily surpasses that of a 16436 MTU and indeed the packet sizes sent are generally larger than 16436. I don't see any obvious downsides for slower peers or connections, but it would be prudent to test this extensively to ensure that those cases don't regress. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Thomas Gleixner 提交于
Revert commit f62f1fc9 Author: Yinghai Lu <yhlu.kernel@gmail.com> Date: Fri Mar 7 15:02:50 2008 -0800 x86: reserve dma32 early for gart The patch has a dependency on bootmem modifications which are not .25 material that late in the -rc cycle. The problem which is addressed by the patch is limited to machines with 256G and more memory booted with NUMA disabled. This is not a .25 regression and the audience which is affected by this problem is very limited, so it's safer to do the revert than pulling in intrusive bootmem changes right now. Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
- 22 3月, 2008 2 次提交
-
-
This reverts commit d48567dd. Borislav is working on ide-tape "light" version instead. Cc: Borislav Petkov <petkovbb@gmail.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Mark "hdx=remap" and "hdx=remap63" kernel parameters as obsoleted (they are layering violation and should be dealt with in the same way as done by libata - device-mapper should be used instead). Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-