Fix PCI kernel-doc warning:

Warning(linux-2.6.29-rc4-git1/drivers/pci/rom.c:67): No description found for parameter 'pdev'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Hidetoshi Seto points out that commit
bffac3c5 has wrong values in the array.
Rather than correct the array, we can just use a bounds check and
perform the calculation specified in the comment.  As a bonus, this will
not run off the end of the array if the device specifies an illegal
value in the MSI capability.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
  wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
  net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
  netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
  bnx2: Update version to 1.9.2 and copyright.
  bnx2: Fix jumbo frames error handling.
  bnx2: Update 5709 firmware.
  bnx2: Update 5706/5708 firmware.
  3c505: do not set pcb->data.raw beyond its size
  Documentation/connector/cn_test.c: don't use gfp_any()
  net: don't use in_atomic() in gfp_any()
  IRDA: cnt is off by 1
  netxen: remove pcie workaround
  sun3: print when lance_open() fails
  qlge: bugfix: Add missing rx buf clean index on early exit.
  qlge: bugfix: Fix RX scaling values.
  qlge: bugfix: Fix TSO breakage.
  qlge: bugfix: Add missing dev_kfree_skb_any() call.
  qlge: bugfix: Add missing put_page() call.
  qlge: bugfix: Fix fatal error recovery hang.
  qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
  ...

When a non-wimax interface is looked up by the stack, a bad pointer is
returned when the looked-up interface is not found in the list (of
registered WiMAX interfaces). This causes an oops in the caller when
trying to use the pointer.

Fix by properly setting the pointer to NULL if we don't exit from the
list_for_each() with a found entry.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function sock_getsockopt() located in net/core/sock.c, optval v.val
is not correctly initialized and directly returned in userland in case
we have SO_BSDCOMPAT option set.

This dummy code should trigger the bug:

int main(void)
{
	unsigned char buf[4] = { 0, 0, 0, 0 };
	int len;
	int sock;
	sock = socket(33, 2, 2);
	getsockopt(sock, 1, SO_BSDCOMPAT, &buf, &len);
	printf("%x%x%x%x\n", buf[0], buf[1], buf[2], buf[3]);
	close(sock);
}

Here is a patch that fix this bug by initalizing v.val just after its
declaration.
Signed-off-by: NClément Lecigne <clement.lecigne@netasq.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’ 
defined but not used

We do not need label ‘set_32_bit_mask’  on IA64 platform,So move it to #else.
Signed-off-by: NYang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them.  Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers.  In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers.  In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cn_test_timer_func() is a timer handler and can never use GFP_KERNEL -
there's no point in using gfp_any() here.

Also, use setup_timer().
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The problem is that in_atomic() will return false inside spinlocks if
CONFIG_PREEMPT=n.  This will lead to deadlockable GFP_KERNEL allocations
from spinlocked regions.

Secondly, if CONFIG_PREEMPT=y, this bug solves itself because networking
will instead use GFP_ATOMIC from this callsite.  Hence we won't get the
might_sleep() debugging warnings which would have informed us of the buggy
callsites.

Solve both these problems by switching to in_interrupt().  Now, if someone
runs a gfp_any() allocation from inside spinlock we will get the warning
if CONFIG_PREEMPT=y.

I reviewed all callsites and most of them were too complex for my little
brain and none of them documented their interface requirements.  I have no
idea what this patch will do.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no prior break occurs, cnt reaches 101 after the loop, so we are still able
to change speed when cnt has become 100.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.

The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs.  This can happen when a
page alloc or dma mapping fails.  If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We put the skb back if we can't get mapping for it.  We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We put the page back if we can't get mapping for it.  We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With while (limit--) { ... } limit reaches -1, so 0 means success.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  mm: Export symbol ksize()

A bug was introduced into write_cache_pages cyclic writeout by commit
31a12666 ("mm: write_cache_pages cyclic
fix").  The intention (and comments) is that we should cycle back and
look for more dirty pages at the beginning of the file if there is no
more work to be done.

But the !done condition was dropped from the test.  This means that any
time the page writeout loop breaks (eg.  due to nr_to_write == 0), we
will set index to 0, then goto again.  This will set done_index to
index, then find done is set, so will proceed to the end of the
function.  When updating mapping->writeback_index for cyclic writeout,
we now use done_index == 0, so we're always cycling back to 0.

This seemed to be causing random mmap writes (slapadd and iozone) to
start writing more pages from the LRU and writeout would slowdown, and
caused bugzilla entry

	http://bugzilla.kernel.org/show_bug.cgi?id=12604

about Berkeley DB slowing down dramatically.

With this patch, iozone random write performance is increased nearly
5x on my system (iozone -B -r 4k -s 64k -s 512m -s 1200m on ext2).
Signed-off-by: NNick Piggin <npiggin@suse.de>
Reported-and-tested-by: NJan Kara <jack@suse.cz>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 7b2cd92a ("crypto: api - Fix
zeroing on free") added modular user of ksize(). Export that to fix
crypto.ko compilation.

Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NKirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

* git://git.infradead.org/users/cbou/battery-2.6.29:
  pcf50633_charger: Fix typo

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12646

When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees.  These are bothe well within the -55 - +125 degree
range for the sensor.

Fix overflow in left-shift of a u8.
Signed-off-by: NIan Dall <ian@beware.dropbear.id.au>
Signed-off-by: NEvgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a problem that causes I/O to a disconnected (or partially initialized)
nbd device to hang indefinitely.  To reproduce:

# ioctl NBD_SET_SIZE_BLOCKS /dev/nbd23 514048
# dd if=/dev/nbd23 of=/dev/null bs=4096 count=1

...hangs...

This can also occur when an nbd device loses its nbd-client/server
connection.  Although we clear the queue of any outstanding I/Os after the
client/server connection fails, any additional I/Os that get queued later
will hang.

This bug may also be the problem reported in this bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12277

Testing would need to be performed to determine if the two issues are the
same.

This problem was introduced by the new request handling thread code ("NBD:
allow nbd to be used locally", 3/2008), which entered into mainline around
2.6.25.

The fix, which is fairly simple, is to restore the check for lo->sock
being NULL in do_nbd_request.  This causes I/O to an uninitialized nbd to
immediately fail with an I/O error, as it did prior to the introduction of
this bug.
Signed-off-by: NPaul Clements <paul.clements@steeleye.com>
Reported-by: NJon Nelson <jnelson-kernel-bugzilla@jamponi.net>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: <stable@kernel.org>		[2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Christophe Saout reported [in precursor to:
http://marc.info/?l=linux-kernel&m=123209902707347&w=4]:

> Note that I also some a different issue with CONFIG_UNEVICTABLE_LRU.
> Seems like Xen tears down current->mm early on process termination, so
> that __get_user_pages in exit_mmap causes nasty messages when the
> process had any mlocked pages.  (in fact, it somehow manages to get into
> the swapping code and produces a null pointer dereference trying to get
> a swap token)

Jeremy explained:

Yes.  In the normal case under Xen, an in-use pagetable is "pinned",
meaning that it is RO to the kernel, and all updates must go via hypercall
(or writes are trapped and emulated, which is much the same thing).  An
unpinned pagetable is not currently in use by any process, and can be
directly accessed as normal RW pages.

As an optimisation at process exit time, we unpin the pagetable as early
as possible (switching the process to init_mm), so that all the normal
pagetable teardown can happen with direct memory accesses.

This happens in exit_mmap() -> arch_exit_mmap().  The munlocking happens
a few lines below.  The obvious thing to do would be to move
arch_exit_mmap() to below the munlock code, but I think we'd want to
call it even if mm->mmap is NULL, just to be on the safe side.

Thus, this patch:

exit_mmap() needs to unlock any locked vmas before calling arch_exit_mmap,
as the latter may switch the current mm to init_mm, which would cause the
former to fail.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Christophe Saout <christophe@saout.de>
Cc: Keir Fraser <keir.fraser@eu.citrix.com>
Cc: Christophe Saout <christophe@saout.de>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: <stable@kernel.org>		[2.6.28.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since netmos 9835 with subids 0x1014(IBM):0x0299 is now bound with
serial/8250_pci, because it has no parallel ports and subdevice id isn't
in the expected form, return -ENODEV from probe function.

This is performed in netmos preinit_hook.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit dcf6a79d ("write-back: fix
nr_to_write counter") fixed nr_to_write counter, but didn't set the break
condition properly.

If nr_to_write == 0 after being decremented it will loop one more time
before setting done = 1 and breaking the loop.

[akpm@linux-foundation.org: coding-style fixes]
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With the new system call defines we get this on uml:

arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x308): undefined reference to `sys_sigprocmask'

Reason for this is that uml passes the preprocessor option
-Dsigprocmask=kernel_sigprocmask to gcc when compiling the kernel.
This causes SYSCALL_DEFINE3(sigprocmask, ...) to be expanded to
SYSCALL_DEFINEx(3, kernel_sigprocmask, ...) and finally to a system
call named sys_kernel_sigprocmask.  However sys_sigprocmask is missing
because of this.

To avoid macro expansion for the system call name just concatenate the
name at first define instead of carrying it through severel levels.
This was pointed out by Al Viro.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: NWANG Cong <wangcong@zeuux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For a reason that I was unable to understand in three months of debugging,
mount ext2 -o remount stopped working properly when remounting from
regular operation to xip, or the other way around.  According to a git
bisect search, the problem was introduced with the VM_MIXEDMAP/PTE_SPECIAL
rework in the vm:

commit 70688e4d
Author: Nick Piggin <npiggin@suse.de>
Date:   Mon Apr 28 02:13:02 2008 -0700

    xip: support non-struct page backed memory

In the failing scenario, the filesystem is mounted read only via root=
kernel parameter on s390x.  During remount (in rc.sysinit), the inodes of
the bash binary and its libraries are busy and cannot be invalidated (the
bash which is running rc.sysinit resides on subject filesystem).
Afterwards, another bash process (running ifup-eth) recurses into a
subshell, runs dup_mm (via fork).  Some of the mappings in this bash
process were created from inodes that could not be invalidated during
remount.

Both parent and child process crash some time later due to inconsistencies
in their address spaces.  The issue seems to be timing sensitive, various
attempts to recreate it have failed.

This patch refuses to change the xip flag during remount in case some
inodes cannot be invalidated.  This patch keeps users from running into
that issue.

[akpm@linux-foundation.org: cleanup]
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I enabled all cgroup subsystems when compiling kernel, and then:
 # mount -t cgroup -o net_cls xxx /mnt
 # mkdir /mnt/0

This showed up immediately:
 BUG: MAX_LOCKDEP_SUBCLASSES too low!
 turning off the locking correctness validator.

It's caused by the cgroup hierarchy lock:
	for (i = 0; i < CGROUP_SUBSYS_COUNT; i++) {
		struct cgroup_subsys *ss = subsys[i];
		if (ss->root == root)
			mutex_lock_nested(&ss->hierarchy_mutex, i);
	}

Now we have 9 cgroup subsystems, and the above 'i' for net_cls is 8, but
MAX_LOCKDEP_SUBCLASSES is 8.

This patch uses different lockdep keys for different subsystems.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Acked-by: NPaul Menage <menage@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add Li Zefan as co-maintainer.
Acked-by: NPaul Menage <menage@google.com>
Acked-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With a postfix decrement t will reach -1 rather than 0, so neither the
warning nor the `goto error_out' will occur.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc processing of SYSCALL wrappers.

The SYSCALL wrapper patches played havoc with kernel-doc for
syscalls.  Syscalls that were scanned for DocBook processing
reported warnings like this one, for sys_tgkill:

Warning(kernel/signal.c:2285): No description found for parameter 'tgkill'
Warning(kernel/signal.c:2285): No description found for parameter 'pid_t'
Warning(kernel/signal.c:2285): No description found for parameter 'int'

because the macro parameters all "look like" function parameters,
although they are not:

/**
 *  sys_tgkill - send signal to one specific thread
 *  @tgid: the thread group ID of the thread
 *  @pid: the PID of the thread
 *  @sig: signal to be sent
 *
 *  This syscall also checks the @tgid and returns -ESRCH even if the PID
 *  exists but it's not belonging to the target process anymore. This
 *  method solves the problem of threads exiting and PIDs getting reused.
 */
SYSCALL_DEFINE3(tgkill, pid_t, tgid, pid_t, pid, int, sig)
{
...

This patch special-cases the handling SYSCALL_DEFINE* function
prototypes by expanding them to
	long sys_foobar(type1 arg1, type1 arg2, ...)
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc-nano-HOWTO.txt to use */ as the ending marker in kernel-doc
examples and state that */ is the preferred ending marker.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Reported-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>