Enable runtime power management (RTPM) for PCIe devices and implement
the corresponding functions to enable D0i3 mode when the device is
idle.

Additionally, remove some unnecessary #ifdef's because the RTPM code
will not be called if runtime PM is not configured.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add an initial implementation of runtime power management (RTPM) for
PCI devices.  With this patch, RTPM is only used when wifi is off
(i.e. the wifi interface is down).  This implementation is behind a
new Kconfig flag, IWLWIFI_PCIE_RTPM.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The 9000 series introduces several changes in the device
DMA operation.
As the device now supports multi-queue rx, several DMA channels
should be configured.
The flows of providing the device with the allocated RBDs now
changes as well - the device maintains a separate table of used
and free table.

The hardware may use the free table to feed RBDs to any queue.
This requires maintaing a shared table to map returned RBDs to
the original RXB - for that purpose the VID is introduced - an
internal identifier of the RB placed in the lower 12 bits and
returned by HW in the used data.

Another change is the support of 64 bit DMA address.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The 9000 series devices will support multi rx queues.
Current code has one static rx queue - change it to allocate
a number of queues per the device capability (pre-9000 devices
have the number of rx queues set to one).

Subsequent generalizations are:

Change the code to access an explicit numbered rx queue only
when the queue number is known - when handling interrupt, when
accessing the default queue and when iterating the queues.
The rest of the functions will receive the rx queue as a pointer.

Generalize the warning in allocation failure to consider the
allocator status instead of a single rx queue status.

Move the rx initial pool of memory buffers to be shared among
all the queues and allocated to the default queue on init.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the Tx queues are full above a threshold, we
immediately stop the mac80211's queue to stop getting new
packets. This worked until TSO was enabled.
With TSO, one single packet from mac80211 can use many
descriptors since a large send needs to be split into
several segments.
This means that stopping mac80211's queues is not enough
and we also need to ensure that we don't overflow the Tx
queues with one single packet from mac80211.
Add code to transport layer to do just that. Stop
mac80211's queue as soon as the queue is full above the
same threshold as before, and keep pushing the current
packet along with its segments on the queue, but check
that we don't overflow. If that would happen, buffer the
segments, and send them when there is room in the Tx queue
again. Of course, we first need to send the buffered
segments and only then, wake up mac80211's queues.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

8000 device family has a new debug engine that needs to be
configured differently than 7000's.
The debug engine's DMA works in chunks of memory and the
size of the buffer really means the start of the last
chunk. Since one chunk is 256-byte long, we should
configure the device to write to buffer_size - 256.
This fixes a situation were the device would write to
memory it is not allowed to access.

CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The debug functions of fw-dbg.c don't really need to modify
the trigger and the description they receive as a parameter.
Constify the pointers.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Update and fix some 7265 PCI IDs entries.

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the callers used silent = false.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A new PCI IDs update to the 8000 and 9000 series.

type=feature
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the op_mode sends an skb whose payload is bigger than
MSS, PCIe will create an A-MSDU out of it. PCIe assumes
that the skb that is coming from the op_mode can fit in one
A-MSDU. It is the op_mode's responsibility to make sure
that this guarantee holds.

Additional headers need to be built for the subframes.
The TSO core code takes care of the IP / TCP headers and
the driver takes care of the 802.11 subframe headers.

These headers are stored on a per-cpu page that is re-used
for all the packets handled on that same CPU. Each skb
holds a reference to that page and releases the page when
it is reclaimed. When the page gets full, it is released
and a new one is allocated.

Since any SKB that doesn't go through the fast-xmit path
of mac80211 will be segmented, we can assume here that the
packet is not WEP / TKIP and has a proper SNAP header.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The code that handles the TBs that contain the WiFi payload
will be changed for TSO. Move the current code into a
separate function.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow to configure the driver to pretend to have TX CSUM
offload support. This will be useful to test the TSO flows
that will come in further patches.
This configuration is disabled by default.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The d0i3_mode variable is used to distinguish between transports that
handle d0i3 entry during suspend by themselves (i.e. the slave
transports) and those which rely on the op_mode layer to do it.  The
reason why the former do it by themselves is that they need to
transition from d0i3 in runtime_suspend into d0i3 in system-wide
suspend and this transition needs to happen before the op_mode's
suspend flow is called.

The wowlan_d0i3 element is also a bit confusing, because it just
reflects the wowlan->any value for the trans to understand.  This is a
bit unclear in the code and not generic enough for future use.

To make it clearer and to generalize the platform power mode settings,
introduce two variables to indicate the platform power management
modes used by the transport.

Additionally, in order not to take too big a step in one patch, treat
this new variables semantically in the same way as the old d0i3_mode
element, introducing a iwl_mvm_enter_d0i3_on_suspend() function to
help with that.

This commit also adds the foundation for a new concept where the
firmware configuration state (i.e. D0, D3 or D0i3) is abstracted from
the platform PM mode we are in (i.e. runtime suspend or system-wide
suspend).
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Host commands now have a group id, express this in printed messages.
Signed-off-by: NSharon Dvir <sharon.dvir@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows the op_mode to request from the transport to
call a callback when an ASYNC commands is completed by
the firmware. The same callback will be called for all the
commands. Pass the command whose response triggers the
callback as a parameter to the callback itself.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In certain flows (see next patches), the op_mode may need to
block the Tx queues for a short period. Provide an API for
that. The transport is in charge of counting the number of
times the queues are blocked since the op_mode may block the
queues several times in a row before unblocking them.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new struct for the 8165 series and a few new
PCI ID entries.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new struct for the 3168 series and a few new
PCI ID entries.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add 9000-family configuration to iwl_cfg struct
Add a new struct to define the 5165 series.
Rename the struct that defines the 9000 series to 9260.
Add some new sub-system IDs for the 9260 and 5165 series.
For 9260:
0x0A10, 0x0000, 0x0510, 0x0710, 0x0410, 0x0610.
For 5165:
0x2A10, 0x2010, 0x0310, 0x0210.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since this pointer is not shown anywhere else, it's useless.
Remove it, just keeping the indexes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Transport code currently calls itself through the transport ops,
which is quite pointless. Clean up all of this. While at it,
remove the unnecessary dir argument and the redundant IDI code.

In slave transports, call both the common slave debugfs and the
transport's own. SDIO has no files, so remove it all there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the prph registers dump is in the transport layer,
and each bus needs an additional dump implementation.

Move the prph dump outside transport, and allow a common
implementation for all of the buses.
This is possible because prph base addresses are similar for
all buses.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Expose _no_grab prph i/o functions that allow performing i/o
outside the transport, without requiring grab and release NIC access
for each operation. In addition, rename the functions so they reflect
their non-grabbing behavior.

This can be very useful for consecutive prph i/o operation that occur
outside trans, such as fw dumps.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This message isn't very useful and presents a security risk
due to the use of %p - remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make the various conversion functions typesafe, so we don't
accidentally try to call them with the wrong pointers and
cast them to something that will crash.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

802.11ac allows A-MSDU that can be up to 12KB long. Since
an entire A-MSDU needs to fit into one single Receive
Buffer (RB), add support for big RBs.
Since this adds lots of pressure to the memory manager and
significantly increase the true_size of the RX buffers,
don't enable this by default.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>