_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.

This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: NGerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE.  Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE.  Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system.  Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.

Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should.  Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

These are all powerpc specific drivers.

res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit.  Thanks to Scott Wood for noticing.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Remove some leftover cruft from the arch/ppc days
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Manual merge of:
	arch/powerpc/configs/44x/warp_defconfig

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
  USB: Driver for Freescale QUICC Engine USB Host Controller
  USB: option: add QUANTA HSDPA Data Card device ids
  USB: storage: Add another unusual_dev for off-by-one bug
  USB: unusual_dev: usb-storage needs to ignore a device
  USB: GADGET: fix !x & y
  USB: new id for ti_usb_3410_5052 driver
  USB: cdc-acm: Add another conexant modem to the quirks
  USB: 'option' driver - onda device MT503HS has wrong id
  USB: Remove ZTE modem from unusual_devices
  USB: storage: support of Dane-Elec MediaTouch USB device
  USB: usbmon: Implement compat_ioctl
  USB: add kernel-doc for wusb_dev in struct usb_device
  USB: ftdi_sio driver support of bar code scanner from Diebold
  USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
  USB: cp2101 device
  USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
  USB: remove vernier labpro from ldusb
  USB: CDC-ACM quirk for MTK GPS
  USB: cdc-acm: support some gps data loggers
  USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
  ...

This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.

Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.

This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the support  for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: NAlex Cheng <alex.cheng@quantatw.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.

Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.


At this time usb_modeswitch does not work with this device.


Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

! has a higher precedence than &
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds a new device id
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Another Conexant, another device with the same quirk
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).

This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: NMarcel Sebek <sebek64@post.cz>
Acked-by: NDomenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.

Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: NJean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0

It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.

This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reported by Randy Dunlap from a warning on the v2.6.29 merge window.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: NMhayk Whandson <eu@mhayk.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: NRobie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,

PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c

From: Tomasz K <eros81@o2.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?

output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):

before patch

open("/dev/usb/lp0", O_RDWR|O_EXCL)     = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)

after patch

open("/dev/usb/lp0", O_RDWR|O_EXCL)     = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0

Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638Signed-off-by: NBrandon Philips <bphilips@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: Nstephen ware <stephen.ware@eqware.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.

I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: NAndrew Lunn, <andrew@lunn.ch>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.

From: James A. Treacy <treacy@debian.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index

In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.

This patch fixes this issue.
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NBryan Wu <cooloney@kernel.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies.  This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:

  drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
  drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
  drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: NHugo Villeneuve <hugo@hugovil.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
  #include <linux/usb/...>
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
  No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
  No such file or directory
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes insert module failure as free_irq() was not
done in previous rmmod.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Trying once more to get this merged.  The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged.  Neither
were any of the numerous subsequent resends.  Sigh.

  CC      drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

> > drivers/built-in.o: In function `ohci_omap_init':
 > > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver'
 > > drivers/built-in.o: In function `omap_udc_probe':
 > > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver'
 > > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver'
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1198) fixes a conceptual bug: Somewhere along the line
we managed to confuse USB class devices with USB char devices.  As a
result, the code to send a disconnect signal to userspace would not be
built if both CONFIG_USB_DEVICE_CLASS and CONFIG_USB_DEVICEFS were
disabled.

The usb_fs_classdev_common_remove() routine has been renamed to
usbdev_remove() and it is now called whenever any USB device is
removed, not just when a class device is unregistered.  The notifier
registration and unregistration calls are no longer conditionally
compiled.  And since the common removal code will always be called as
part of the char device interface, there's no need to call it again as
part of the usbfs interface; thus the invocation of
usb_fs_classdev_common_remove() has been taken out of
usbfs_remove_device().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NAlon Bar-Lev <alon.barlev@gmail.com>
Tested-by: NAlon Bar-Lev <alon.barlev@gmail.com>
Cc: stable <stable@kernel.org>

Commit a0d4922d
(USB: fix up suspend and resume for PCI host controllers) attempted
to fix the suspend-resume of PCI USB controllers, but unfortunately
it did that incorrectly and interrupts are left enabled by the USB
controllers' ->suspend_late() callback as a result.  This leads to
serious problems during suspend which are very difficult to debug.

Fix the issue by removing the ->suspend_late() callback of PCI
USB controllers and moving the code from there to the ->suspend()
callback executed with interrupts enabled.  Additionally, make
the ->resume() callback of PCI USB controllers execute
pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the
full power state (PCI_D0).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Tested-by: N"Jeff Chua" <jeff.chua.linux@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>