As per DP spec when R0 mismatch is detected, HDCP source supported
re-read the R0 atleast twice.

And For HDMI and DP minimum wait required for the R0 availability is
100mSec. So this patch changes the wait time to 100mSec but retries
twice with the time interval of 100mSec for each attempt.

This patch is needed for DP HDCP1.4 CTS Test: 1A-06.

v2:
  No Change
v3:
  Comment on R0 retry is moved closer to the code[Seanpaul]
v4:
  Removing unwanted noise introduced in v3.
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522669822-2508-1-git-send-email-ramalingam.c@intel.com

Let's avoid having to delve down the pointer chain to see if the i915
device has support for preemption and store that on the engine, which
made the decision in the first place!

v2: Refactor common preemption policy between execlists/guc.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403183537.5522-1-chris@chris-wilson.co.uk

We would like to start doing some bookkeeping at the beginning, between
contexts and at the end of execlists submission. We already mark the
beginning and end using EXECLISTS_ACTIVE_USER, to provide an indication
when the HW is idle. This give us a pair of sequence points we can then
expand on for further bookkeeping.

v2: Refactor guc submission to share the same begin/end.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180331130626.10712-1-chris@chris-wilson.co.uk

Commit 'aee3bac0 ("drm/i915/psr: Tie PSR2 support to Y
coordinate requirement")' got merged to drm-intel-next-queued
but the variable was defined commit 'c5fe4732 ("drm: Add PSR
version 3 macro") who was merged through drm-misc.

So backmerging to get drm-intel-next-queued compiling back again.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

In the 2 eDP1.4a pannels tested set or not set bit have no effect
but is better set it and comply with specification.
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-9-jose.souza@intel.com

This value do not change overtime so better cache it than
fetch it every PSR enable.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-8-jose.souza@intel.com

Cosmetic change.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-7-jose.souza@intel.com

Sink can support our PSR2 requirements but userspace can request
a resolution that PSR2 hardware do not support, in this case it
was overwritten the PSR2 sink support.
Adding another flag here, this way if requested resolution changed
to a value that PSR2 hardware can handle, PSR2 can be enabled.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-6-jose.souza@intel.com

For Geminilake and Cannonlake+ the Y-coordinate support must be
enabled in PSR2_CTL too.

Spec: 7713 and 7720

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-5-jose.souza@intel.com

Although i915 don't implement aux sync frame through tests was
findout that pannels can do selective update when the y-coordinate
is also included in SDP, that is why it is required to run PSR2 in
i915.

So moving to only one place the sink requirements that the actual
driver needs to enable PSR2.

Also intel_psr2_config_valid() is called every time the crtc config
is computed, wasting some time every time it was checking for
Y coordinate requirement.

This allow us to nuke y_cord_support and some of VSC setup code that
was handling a scenario that would never happen(PSR2 without Y
coordinate).

Also here renaming intel_dp_get_y_cord_status() to
intel_dp_get_y_coord_required() as it more accurate to the name and
function of bit according to eDP spec.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-4-jose.souza@intel.com

eDP spec states that aux frame is required to do PSR2 selective
update but i915 don't fully implement it. It sends the aux frame
sync messages but the value is always zero as the GTC is not enabled
in driver.

Through tests was findout that pannels can do selective update when
the y-coordinate is also included in SDP, that is why it is required
to run PSR2 in i915.

A dummy value is not useful at all to sink, so removing everything
related to aux frame sync, if GTC is enabled we can bring this back.

Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-3-jose.souza@intel.com

This is a register to help debug what is in the last SDP VSC
packet revived by sink.
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-2-jose.souza@intel.com

To comply with eDP1.4a this bit should be set when enabling PSR2.
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-1-jose.souza@intel.com

As intel_wait_for_register_fw() may use, and if successful only use, a
busy-wait loop, the might_sleep() warning is a little over-zealous.
Restrict it to a might_sleep_if() a slow timeout is specified (and so
the caller authorises use of a usleep).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180329224519.13598-2-chris@chris-wilson.co.uk

Only sleep and repeat when asked for a full device reset (ALL_ENGINES)
and avoid using sleeping waits when asked for a per-engine reset. The
goal is to be able to use a per-engine reset from hardirq/softirq/timer
context. A consequence is that our individual wait timeouts are a
thousand times shorter, on the order of a hundred microseconds rather
than hundreds of millisecond. This may make hitting the timeouts more
common, but hopefully the fallover to the full-device reset will be
sufficient to pick up the pieces.

Note, that the sleeps inside older gen (pre-gen8) have been left as they
are only used in full device reset mode.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180329224519.13598-1-chris@chris-wilson.co.uk

This will make it easier to spot issues related to config
creation/usage.
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326090831.22686-9-lionel.g.landwerlin@intel.com

We had a generic field name used across 2 registers but it feels like
it's clearer we make it obvious what register this field belongs to.
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326090831.22686-7-lionel.g.landwerlin@intel.com

This was added by mistake in commit 28964cf2 ("drm/i915/perf:
disable NOA logic when not used").
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326090831.22686-6-lionel.g.landwerlin@intel.com

In commit d7965152 ("drm/i915: Enable i915 perf stream for
Haswell OA unit") the enable/disable vfunc hadn't appear yet and the
same function would deal with enabling/disabling the OA unit.

This was split later on for gen8 but the gen7 retained some code that
isn't actually useful anymore.
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326090831.22686-4-lionel.g.landwerlin@intel.com

We've been a bit loose about this opening parameter. We should only
add the flag for writing OA reports when the value of this parameter
is != 0.
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326090831.22686-3-lionel.g.landwerlin@intel.com

No significant changes from either context offsets, nor report
formats, nor register whitelist.

v2: Also drop slice/unslice clock ratio changes (Matt)
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326133949.12469-3-lionel.g.landwerlin@intel.com

When we include a request's global_seqno in a GEM_TRACE it often helps
to know how that relates to the current breadcrumb as seen by the
hardware.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327210157.16896-3-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Probably lost while rebasing commit eacd8391 ("drm/i915/guc: Keep GuC
interrupts enabled when using GuC").

Not really needed since i915_gem_init_hw is called before uc_resume, but
it brings symmetry to uc_suspend.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328205851.16188-1-michel.thierry@intel.com

- Mask mode type garbage from userspace (Ville)

Something went wrong on the misc tree side, but I'll pull the patch directly.

* 'drm-misc-next-fixes' of git://anongit.freedesktop.org/drm/drm-misc:
  drm: Fix uabi regression by allowing garbage mode->type from userspace

During debug we may want to investigate all communication
from the Guc. Add proper tracing macros in debug config.

v2: convert remaining DRM_DEBUG into new CT_DEBUG (Michal)
v3: use dedicated Kconfig (Daniele)
v4: checkpatch
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-12-michal.wajdeczko@intel.com

When running on platform with CTB based GuC communication enabled,
GuC to Host event data will be delivered as CT request message.
However, content of the data[1] of this CT message follows format
of the scratch register used in MMIO based communication, so some
code reuse is still possible.

v2:  filter disabled messages (Daniele)
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #1
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327214124.70680-1-michal.wajdeczko@intel.com

Requests are read from CT in the irq handler, but actual processing
will be done in the work thread. Processing of specific actions will
be added in the upcoming patches.

v2: don't use GEM_BUG_ON (Chris)
    don't kmalloc too large buffer (Michal)
v3: rebased
v4: don't name it 'dispatch' (Michel) and fix checkpatch
    add some documentation (Michal)
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-10-michal.wajdeczko@intel.com

Instead of returning small data in response status dword,
GuC may append longer data as response message payload.
If caller provides response buffer, we will copy received
data and use number of received data dwords as new success
return value. We will WARN if response from GuC does not
match caller expectation.

v2: fix timeout and checkpatch warnings (Michal)
v3: fix checkpatch again (Michel)
    update wait function name (Michal)
    no need for spinlock_irqsave (MichalWi)
    no magic numbers (MichalWi)
    must check before use (Jani)
    add some more documentation (Michal)
v4: update documentation (Michal)
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #2.5
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327121439.70096-1-michal.wajdeczko@intel.com

In next patch we will introduce another way of waiting for the response
that will use RECV buffer. To avoid misleading names, rename old wait
function to reflect the fact that it is based on descriptor update.

v2: fix comment style (Michal)
v3: use more specific name (Michel)
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-8-michal.wajdeczko@intel.com

GuC can respond to our commands not only by updating SEND buffer
descriptor, but can also send a response message over RECV buffer.
Guc can also send unsolicited request messages over RECV buffer.
Let's start reading those messages and make placeholders
for actual response/request handlers.

v2: misc improvements (Michal)
v3: change response detection (Michal)
    invalid status is protocol error (Michal)
v4: rebase
v5: fix checkpatch (Michel)
    don't use fields before check (Jani)
    add some documentation (Michal)
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> # 4.5
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-7-michal.wajdeczko@intel.com

On platforms with CTB based GuC communications, we will handle
GuC events in a different way. Let's make event handler a virtual
function to allow easy switch between those variants.

Credits-to: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-6-michal.wajdeczko@intel.com

We're using data encoded in the status MMIO as return value from send
function, but GuC may also write more data in remaining MMIO regs.
Let's copy content of these registers to the buffer provided by caller.

v2: new line (Michel)
v3: updated commit message
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-5-michal.wajdeczko@intel.com

This is a preparation step for the upcoming patches.
We already can return some small data decoded from the command
status, but we will need more in the future.

v2: add explicit response buf size
v3: squash with helper patch
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-4-michal.wajdeczko@intel.com

GuC may return additional data in the response message.
Format and meaning of this data is action specific. We will
use this non-negative data as a new success return value.
Currently used actions don't return data that way yet.

v2: fix prohibited space after '~' (Michel)
    update commit message (Daniele)
v3: rebase
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-3-michal.wajdeczko@intel.com

As we are going to extend our use of MMIO based communication,
try to explain its mechanics and update corresponding definitions.

v2: fix checkpatch MACRO_ARG_REUSE
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Kelvin Gardiner <kelvin.gardiner@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #1
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326194829.58836-2-michal.wajdeczko@intel.com

Tvrtko uncovered a fun issue with recovering from a wedge device. In his
tests, he wedged the driver by injecting an unrecoverable hang whilst a
batch was spinning. As we reset the gpu in the middle of the spinner,
when resumed it would continue on from the next instruction in the ring
and write it's breadcrumb. However, on wedging we updated our
bookkeeping to indicate that the GPU had completed executing and would
restart from after the breadcrumb; so the emission of the stale
breadcrumb from before the reset came as a bit of a surprise.

A simple fix is to when rebinding the context into the GPU, we update
the ring register state in the context image to match our bookkeeping.
We already have to update the RING_START and RING_TAIL, so updating
RING_HEAD as well is trivial. This works because whenever we unbind the
context, we keep the bookkeeping in check; and on wedging we unbind all
contexts.

Testcase: igt/gem_eio
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327210136.16750-1-chris@chris-wilson.co.ukTested-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

The only thing that differs here is that the crystal clock freq now
has four possible values.

This patch gets rid of the "Unknown gen, unable to compute..." message
at boot for gen11.
Reviewed-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109232835.11478-18-paulo.r.zanoni@intel.com

GuC Address Space and WOPCM Layout diagrams won't be generated correctly by
sphinx build if not using proper reST syntax.

This patch uses reST literal blocks to make sure GuC Address Space and
WOPCM Layout diagrams to be generated correctly, and it also corrects some
errors in the diagram description.

v2:
 - Fixed errors in diagram description

v3:
 - Updated GuC Address Space kernel-doc based on Michal's suggestion

v4:
 - Added WOPCM layout and GuC address space docs into i915.rst (Joonas)
Signed-off-by: NJackie Li <yaodong.li@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1521763162-11424-1-git-send-email-yaodong.li@intel.com

- GPUVM support for dGPUs
- KFD events support for dGPUs
- Fix live-lock situation when restoring multiple evicted processes
- Fix VM page table allocation on large-bar systems
- Fix for build failure on frv architecture

* tag 'drm-amdkfd-next-2018-03-27' of git://people.freedesktop.org/~gabbayo/linux:
  drm/amdkfd: Use ordered workqueue to restore processes
  drm/amdgpu: Fix acquiring VM on large-BAR systems
  drm/amdkfd: Add module option for testing large-BAR functionality
  drm/amdkfd: Kmap event page for dGPUs
  drm/amdkfd: Add ioctls for GPUVM memory management
  drm/amdkfd: Add TC flush on VMID deallocation for Hawaii
  drm/amdkfd: Allocate CWSR trap handler memory for dGPUs
  drm/amdkfd: Add per-process IDR for buffer handles
  drm/amdkfd: Aperture setup for dGPUs
  drm/amdkfd: Remove limit on number of GPUs
  drm/amdkfd: Populate DRM render device minor
  drm/amdkfd: Create KFD VMs on demand
  drm/amdgpu: Add kfd2kgd interface to acquire an existing VM
  drm/amdgpu: Add helper to turn an existing VM into a compute VM
  drm/amdgpu: Fix initial validation of PD BO for KFD VMs
  drm/amdgpu: Move KFD-specific fields into struct amdgpu_vm
  drm/amdkfd: fix uninitialized variable use
  drm/amdkfd: add missing include of mm.h

Merge tag 'drm-intel-next-fixes-2018-03-27' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

- Display fixes for booting with MST hub lid closed and display
  freezing after hibernation (fd.o bugs 105470 & 105196)
- Fix for a very rare interrupt handling race resulting in GPU hang

* tag 'drm-intel-next-fixes-2018-03-27' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915: Fix hibernation with ACPI S0 target state
  drm/i915/execlists: Use a locked clear_bit() for synchronisation with interrupt
  drm/i915: Specify which engines to reset following semaphore/event lockups
  drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.