Registering usb_hcd_platform_shutdown to be called during
shutdown. This is a generic function that performs the
generic host stack's shutdown. It ensures that USB
operations do not continue while kexec boots a new kernel.
Signed-off-by: NAzriel Samson <asamson@codeaurora.org>
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Reviewed-by: NAndy Gross <andy.gross@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The default value for the 'transceiver select' field of
the PORTSC register may not always be correct. Previously
the phy-msm-usb driver would do this for us, but since
ehci-msm can now be instantiated standalone without any PHY
driver, the register needs to be explicitly initialized to
ULPI mode to properly communicate with the PHY.

This is not readily apparent, as firmware or bootloader code
also happen to pre-initialize this for us. However, it can
manifest when performing a driver unbind/rebind as follows:

 cd /sys/bus/platform/drivers/msm_hsusb_host
 echo QCOM8040:00 > unbind
 echo QCOM8040:00 > bind

The EHCI core executes a controller reset as part of this,
and as a result the register in question would revert to
its default state and must be re-initialized properly.
Furthermore this may be useful in the future when adding
PM suspend/resume support.
Signed-off-by: NJack Pham <jackp@codeaurora.org>
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Reviewed-by: NAndy Gross <andy.gross@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow the EHCI MSM driver to probe against an ACPI enumerated
device with ID QCOM8040.
Signed-off-by: NJack Pham <jackp@codeaurora.org>
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Reviewed-by: NAndy Gross <andy.gross@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the EHCI MSM driver has a hard dependency to be created
by an OTG layer, namely the phy-msm-usb driver. In some cases or
board configurations we want to allow the EHCI host to be
instantiated without OTG capability. Instead, relax the dependency
on having an OTG PHY being present and call usb_add_hcd() directly.
Signed-off-by: NJack Pham <jackp@codeaurora.org>
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Reviewed-by: NAndy Gross <andy.gross@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Disable the silicon quirk which is normally enabled for HSIC
host mode. This would otherwise prevent low speed devices
from enumerating properly.
Signed-off-by: NJack Pham <jackp@codeaurora.org>
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This splits one big probing function into two smaller ones. The main one
is now responsible for the generic stuff: allocating memory & enabling
power using GPIO. The new one contains code that is specific to the USB
2.0 bcma core.
This will allow adding support for the USB 3.0 bcma core (handling XHCI)
in the future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Having "bool ohci" argument in bcma_hcd_create_pdev function limited it
to support two cases only (OHCI and EHCI) and put too much logic in it.
Lets make caller pass all required data. This adds few extra arguments
to the function call but will allow us to reuse this code and handle
more cases in the future (e.g. add XHCI support).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

kbasename() helper is dedicated to find a last part of the filename or
pathname. USB core uses open-coded variant of that helper.

Replace some lines of code by kbasename() call.

The current users do not have trailing slash and we are on the safe side to
make such change. I dig a history of the code under question up and found the
patch [1] that brought it along with the same to tty layer. The check for
trailing slash looks like copy'n'paste thing and I consider it as redundant.

[1] http://www.kernel.org/pub/linux/kernel//people/akpm/patches/2.5/2.5.69/2.5.69-mm3/broken-out/linus.patchSigned-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Change Power architecture specific APIs such as in_be32/out_be32
for registers read/write. Instead using ioread/writebe32 which are
defined for power as well as arm architecture
Signed-off-by: NNikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: NSriram Dash <sriram.dash@freescale.com>
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Set DMA_MASK of usb platform device properly.
Signed-off-by: NSriram Dash <sriram.dash@freescale.com>
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb 3.1 extend the hub get-port-status request by adding different
request types. the new request types return 4 additional bytes called
extended port status, these bytes are returned after the regular
portstatus and portchange values.

The extended port status contains a speed ID for the currently used
sublink speed. A table of supported Speed IDs with details about the link
is provided by the hub in the device descriptor BOS SuperSpeedPlus
device capability Sublink Speed Attributes.

Support this new request. Ask for the extended port status after port
reset if hub supports USB 3.1. If link is running at SuperSpeedPlus
set the device speed to USB_SPEED_SUPER_PLUS
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The same way as SuperSpeed devices show "5000" as device speed we wan't to
show "10000" as the default speed for SuperSpeedPlus devices in sysfs.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A hcd roothub that supports HCD_USB31 is running at SuperSpeedPlus speed
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixing coccicheck warning which recommends to use memdup_user instead
to reimplement its code, using memdup_user simplifies the code

./drivers/usb/core/devio.c:1398:11-18: WARNING opportunity for memdup_user
Signed-off-by: NRahul Pathak <rpathak@visteon.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Removed an unnecessary space between a function name and arguments.
Signed-off-by: NChase Metzger <chasemetzger15@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The usbhs_pkt_handle structures are never modified, so declare them as
const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, the change is needed
to prevent a compilation failure, when mach/irq.h is removed.

Additionally remove other unneeded includes.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.

  The executive summary:

   - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
   - Avoid useless rebuilds for zboot.
   - jz4780: Add NEMC, BCH and NAND device tree nodes
   - Initial support for the MicroChip's DT platform.  As all the device
     drivers are missing this is still of limited use.
   - Some Loongson3 cleanups.
   - The unavoidable whitespace polishing.
   - Reduce clock skew when synchronizing the CPU cycle counters on CPU
     startup.
   - Add MIPS R6 fixes.
   - Lots of cleanups across arch/mips as fallout from KVM.
   - Lots of minor fixes and changes for IEEE 754-2008 support to the
     FPU emulator / fp-assist software.
   - Minor Ralink, BCM47xx and bcm963xx platform support improvments.
   - Support SMP on BCM63168"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
  MIPS: zboot: Add support for serial debug using the PROM
  MIPS: zboot: Avoid useless rebuilds
  MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
  MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
  MIPS: bcm963xx: Update bcm_tag field image_sequence
  MIPS: bcm963xx: Move extended flash address to bcm_tag header file
  MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
  MIPS: bcm63xx: nvram: Use nvram structure definition from header file
  MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
  MAINTAINERS: Add KVM for MIPS entry
  MIPS: KVM: Add missing newline to kvm_err()
  MIPS: Move KVM specific opcodes into asm/inst.h
  MIPS: KVM: Use cacheops.h definitions
  MIPS: Break down cacheops.h definitions
  MIPS: Use EXCCODE_ constants with set_except_vector()
  MIPS: Update trap codes
  MIPS: Move Cause.ExcCode trap codes to mipsregs.h
  MIPS: KVM: Make kvm_mips_{init,exit}() static
  MIPS: KVM: Refactor added offsetof()s
  MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
  ...

Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "Emergency travel prevented me from completing my final testing on this
  until today.  Nothing here that couldn't wait until RC1 fixes, but I
  thought it best to get it out sooner rather than later as it does
  contain a build warning fix.

  Summary:

  A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:

  ideapad-laptop:
   - Add Lenovo Yoga 700 to no_hw_rfkill dmi list

  MAINTAINERS:
   - Combine multiple telemetry entries

  intel_telemetry_debugfs:
   - Fix unused warnings in telemetry debugfs"

* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
  MAINTAINERS: Combine multiple telemetry entries
  intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs

Pull thermal management updates from Zhang Rui:
 "The top merge commit was re-generated yesterday because two topic
  branches were dropped from this pull request in the last minute due to
  some unaddressed comments.  All the other material has been in
  linux-next for quite a while.

  Specifics:

   - Enhance thermal core to handle unexpected device cooling states
     after fresh boot and system resume.  From Zhang Rui and Chen Yu.

   - Several fixes and cleanups on Rockchip and RCAR thermal drivers.
     From Caesar Wang and Kuninori Morimoto.

   - Add Broxton support for Intel processor thermal reporting device
     driver.  From Amy Wiles"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: trip_point_temp_store() calls thermal_zone_device_update()
  thermal: rcar: rcar_thermal_get_temp() return error if strange temp
  thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
  thermal: rcar: check every rcar_thermal_update_temp() return value
  thermal: rcar: move rcar_thermal_dt_ids to upside
  thermal: rockchip: Support the RK3399 SoCs in thermal driver
  thermal: rockchip: Support the RK3228 SoCs in thermal driver
  dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
  thermal: rockchip: fix a trivial typo
  Thermal: Enable Broxton SoC thermal reporting device
  thermal: constify pch_dev_ops structure
  Thermal: do thermal zone update after a cooling device registered
  Thermal: handle thermal zone device properly during system sleep
  Thermal: initialize thermal zone device correctly

Pull 9p updates from Eric Van Hensbergen:
 "Sorry for the last minute pull request, there's was a change that
  didn't get pulled into for-next until two weeks ago and I wanted to
  give it some bake time.

  Summary:

  Rework and error handling fixes, primarily in the fscatch and fd
  transports"

* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: use fscache mutex rather than spinlock
  9p: trans_fd, bail out if recv fcall if missing
  9p: trans_fd, read rework to use p9_parse_header
  net/9p: Add device name details on error

Pull Ceph updates from Sage Weil:
 "The two main changes are aio support in CephFS, and a series that
  fixes several issues in the authentication key timeout/renewal code.

  On top of that are a variety of cleanups and minor bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: remove outdated comment
  libceph: kill off ceph_x_ticket_handler::validity
  libceph: invalidate AUTH in addition to a service ticket
  libceph: fix authorizer invalidation, take 2
  libceph: clear messenger auth_retry flag if we fault
  libceph: fix ceph_msg_revoke()
  libceph: use list_for_each_entry_safe
  ceph: use i_size_{read,write} to get/set i_size
  ceph: re-send AIO write request when getting -EOLDSNAP error
  ceph: Asynchronous IO support
  ceph: Avoid to propagate the invalid page point
  ceph: fix double page_unlock() in page_mkwrite()
  rbd: delete an unnecessary check before rbd_dev_destroy()
  libceph: use list_next_entry instead of list_entry_next
  ceph: ceph_frag_contains_value can be boolean
  ceph: remove unused functions in ceph_frag.h

Pull SMB3 fixes from Steve French:
 "A collection of CIFS/SMB3 fixes.

  It includes a couple bug fixes, a few for improved debugging of
  cifs.ko and some improvements to the way cifs does key generation.

  I do have some additional bug fixes I expect in the next week or two
  (to address a problem found by xfstest, and some fixes for SMB3.11
  dialect, and a couple patches that just came in yesterday that I am
  reviewing)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs_dbg() outputs an uninitialized buffer in cifs_readdir()
  cifs: fix race between call_async() and reconnect()
  Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this.
  cifs: Allow using O_DIRECT with cache=loose
  cifs: Make echo interval tunable
  cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary
  Print IP address of unresponsive server
  cifs: Ratelimit kernel log messages

Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.

This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1295272
Tested-by: <dinyar.rabady+spam@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

This patch combines all the telemetry file entries in MAINTAINERS via
wildcard.
Signed-off-by: NSouvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

This patch fixes compile time warnings when CONFIG_PM_SLEEP
is undefined. In this case sleep related counters are unused.
Signed-off-by: NSouvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

If we detect that there is nothing to do just set the flag and do not
check if it was already set before.  Races really do not matter.  If the
flag is set by any code then the shepherd will start dealing with the
situation and reenable the vmstat workers when necessary again.

Since commit 0eb77e98 ("vmstat: make vmstat_updater deferrable again
and shut down on idle") quiet_vmstat might update cpu_stat_off and mark
a particular cpu to be handled by vmstat_shepherd.  This might trigger a
VM_BUG_ON in vmstat_update because the work item might have been
sleeping during the idle period and see the cpu_stat_off updated after
the wake up.  The VM_BUG_ON is therefore misleading and no more
appropriate.  Moreover it doesn't really suite any protection from real
bugs because vmstat_shepherd will simply reschedule the vmstat_work
anytime it sees a particular cpu set or vmstat_update would do the same
from the worker context directly.  Even when the two would race the
result wouldn't be incorrect as the counters update is fully idempotent.
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NChristoph Lameter <cl@linux.com>
Acked-by: NMichal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.

When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Allow BMIPS_GENERIC supported platforms to build GPIO controller
drivers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NDragan Stancevic <dragan.stancevic@gmail.com>
Cc: cernekee@gmail.com
Cc: jaedon.shin@gmail.com
Cc: gregory.0xf0@gmail.com
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12019/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove bcm63xx_nvram_get_psi_size() as it now has no users.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11836/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The "dual_image" and "inactive_flag" fields should be merged into a single
"image_sequence" field.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11834/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The extended flash address needs to be subtracted from bcm_tag flash
image offsets. Move this value to the bcm_tag header file.

Renamed define name to consistently use bcm963xx for flash layout
which should be considered a property of the board and not the SoC
(i.e. bcm63xx could theoretically be used on a board without CFE
or any flash).
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11833/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move Broadcom BCM963xx image tag data structure to include/linux/
so that drivers outside of mach-bcm63xx can use it.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11832/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use the common definition of the nvram structure from the header file
include/linux/bcm963xx_nvram.h instead of maintaining a separate copy.

Read the version 5 size of nvram data from memory and then call the
new checksum verification function from the header file.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11831/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Broadcom BCM963xx boards have multiple nvram variants across different
SoCs with additional checksum fields added whenever the size of the
nvram was extended.

Add this structure as a header file so that multiple drivers can use it.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11830/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>