Implement suspend and resume callbacks in order to support system
suspend/hibernation.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a clock notifier to dynamically handle frequency changes of the
input clock by reprogramming the UART in order to keep the baud rate
constant.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The original algorithm to find the best baud rate dividers does not necessarily
find the best set of dividers. And in the worst case may even write illegal
values to the hardware.
The new function should make better use of the hardware capabilities and be able
to provide valid settings for a wider range of baud rates and also input clocks.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It is possible that under certain circumstances xuartps_console_write is entered
while the UART disabled. When this happens the code will busy loop in
xuartps_console_putchar, since the character is never written and the TXEMPTY
flag is never set. The result is a system lockup. This patch force enables the
UART for the duration of xuartps_console_write to avoid this.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Changes to use the 64 byte FIFO depth and fix the issue
by clearing the txempty interrupt in isr status for tx
after filling in data in start_tx function
Signed-off-by: NSuneel Garapati <suneelg@xilinx.com>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This allows KDB/KGDB to run.
Signed-off-by: NVlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Cadence UART does not do break detection, even if the
datasheet says it does. This patch adds break detection in
software (tested in 8N1 mode only) and enables SYSRQ,
allowing for Break-g to enter KDB and all the other goodies.
Signed-off-by: NVlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the device managed interface for memory allocation, simplifying
error paths.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the device managed interface for clocks, simplifying error paths.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Migrate the Zynq platform and its drivers to use the new clock
controller driver.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NMike Turquette <mturquette@linaro.org>

Currently Zynq does not support suspend/resume.
The driver callbacks are never used or tested, broken and using the old
PM interface.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Boot ROM has an issue which will cause the driver to
lock up as pending irqs are not being cleared. With them
cleared it prevents that issue.

This patch is needed for the current (3.9-rc3) mainline kernel. I guess
it went unnoticed, because it was only tested with u-boot up until now.
And u-boot maybe handles this.

[s.trumtrar@pengutronix.de: cherry-picked from linux-xlnx.git]
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The datesheet clearly states, that writing low bits to the
XUARTPS_IDR register have no effect. Remove the write.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

__exit_p() need to be removed after the __devexit
removal from the driver.

Warning log:
drivers/tty/serial/xilinx_uartps.c:996:12:
warning: 'xuartps_remove' defined but not used [-Wunused-function]
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for specifying clock information for the uart clk via the
device tree. This eliminates the need to hardcode rates in the device
tree.
Signed-off-by: NJosh Cartwright <josh.cartwright@ni.com>
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.

Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.

IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.

Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: NTobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Zynq platform requires the use of CONFIG_OF.  Remove the #ifdef
conditionals in the uartps driver.  Make dependency explicit in Kconfig.
Signed-off-by: NJosh Cartwright <josh.cartwright@ni.com>
Tested-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We are cleaning up the issue that means module.h is omnipresent.
These tty users are the people who implictly are relying on that.
Fix up the real users to call out the include that they really need.

In the case of jsm_driver.c file, it had moduleparam.h but that
isn't enough and it needs the full module.h
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

linux/tty_flip.h is included in linux/serial_core.h. But this may (and
will) change in the future. Then we would get build errors such as:
.../tty/serial/max3107.c: In function ‘put_data_to_circ_buf’:
.../tty/serial/max3107.c:149:2: error: implicit declaration of function ‘tty_insert_flip_string’

So fix all the drviers which call tty flip buffer helpers to really
include linux/tty_flip.h. And also make sure that those include
linux/tty.h when operating with struct tty_struct.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Xilinx PS Uart is used on the new ARM based SoC. This
UART is not compatible with others such that a seperate
driver is required.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>