The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.

This patch restore sunxi-h3-h5.dtsi
This reverts partially commit fe45174b ("arm: dts: sunxi: Revert EMAC changes")
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch add documentation about the MDIO switch used on sun8i-h3-emac
for integrated PHY.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.

This patch restore dt-bindings documentation about dwmac-sun8i
This reverts commit 8aa33ec2 ("dt-bindings: net: Revert sun8i dwmac binding")
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Banana Pi M2 Ultra board features two USB host ports, connected to the
two USB host ports on the SoC.

Add support for them.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

On the Banana Pi M2 Berry board, the 5V power output (used by HDMI, SATA
and USB) is controlled via a GPIO.

Add regulator node for it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

On newer revisions of the Banana Pi M2 Ultra boards, the 5V power output
(used by HDMI, SATA and USB) is controller via a GPIO.

Add the regulator node for it.

Older revisions just have the 5V power output always on, and the GPIO is
reserved on these boards. So it won't affect the older revisions.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

Allwinner R40 SoC features a USB OTG port and two USB HOST ports.

Add support for the host ports in the DTSI file.

The OTG controller still cannot work with existing compatibles, and needs
more investigation. So it's not added yet.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

Various A10-based development boards have standard HDMI connectors
wired to the dedicated HDMI pins on the SoC.

Enable the display pipeline and HDMI output on boards I have or have
access to schematics:

  - Cubieboard
  - Olimex A10-OLinuXino-LIME
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

All the A20 devices I own have standard HDMI connectors wired
to the dedicated HDMI pins on the SoC:

  - Bananapi M1+
  - Cubieboard 2
  - Cubietruck
  - Lamobo R1 (or Bananapi R1)

Development boards from Olimex also have standard HDMI connectors.
Schematics for them are publicly available. Enable HDMI on them as
well.

  - Olimex A20-OLinuXino-LIME
  - Olimex A20-OLinuXino-LIME2
  - Olimex A20-OLinuXino-MICRO

Enable the display pipeline and HDMI output for them.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Tested-by: Priit Laes <plaes@plaes.org> # Cubietruck, A20-OLinuXino-MICRO
Tested-by: Olliver Schinagl <oliver@schinagl.nl> # A20-OLinuXino-LIME2
Tested-by: Jonathan Liu <net147@gmail.com> # A20-OLinuXino-LIME
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A20 has two interconnected display pipelines, mirroring the A10.

Add all the device nodes for them, including the downstream HDMI
controller that we already support.
Signed-off-by: NJonathan Liu <net147@gmail.com>
[wens@csie.org: Squashed in HDMI and provided commit message]
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A10 has two interconnected display pipelines, much like the A31,
but without the DRCs between the backend and TCONs.

Add all the device nodes for them, including the downstream HDMI
controller that we already support.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The R40 SoC has a watchdog like the one on A20, in the timer memory zone
(which is also the same on A20).

Add the device tree node for it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

The reference design tablet has the DC jack wired to AXP209's ACIN.
As a tablet, it also has an internal LiPo battery, wired to the PMIC's
battery charger.

Enable both.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some boards have had node names with underscores. Remove them in favour of
hyphens in order to reduce the DTC warnings.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some node names in the A80 DTSI still have underscores in them. Remove them
in favour of hyphens to remove DTC warnings.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.

Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The I2C's, MMC0 and EMAC controllers have only one muxing option in the
SoC. In such a case, we can just move the muxing into the DTSI, and remove
it from the DTS.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.

In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

All the A31/A31s devices I own have some kind of HDMI connector wired
to the dedicated HDMI pins on the SoC:

  - A31 Hummingbird (standard HDMI connector, display already enabled)
  - Sinlinx SinA31s (standard HDMI connector)
  - MSI Primo81 tablet (micro HDMI connector)

Enable the display pipeline (if needed) and HDMI output for them.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we support the HDMI controller on the A31 SoC, we can add it
to the device tree.

This adds a device node for the HDMI controller, and the of_graph nodes
connecting it to the 2 TCONs.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.

However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.

Rename the node names to avoid those warnings.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some gpio-keys definitions in our DTs were having buttons defined with a
unit-address and that would generate a DTC warning.

Change the buttons node names to remove the warnings.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The board has an external pull-up on the card-detect signal, so there's no
need to add another one.

This also removes a DTC warning.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The board has an external pull-up on the card-detect signal, so there's no
need to add another one.

This also removes a DTC warning.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Our pinctrl node names were containing unit-adresses without a reg
property, resulting in a warning. Change the names for our new convention.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A80 boards still define some GPIO pinctrl nodes that are not really
useful, and redundant with the muxing already happening on gpio_request.

Let's remove those nodes. This will also remove DTC warnings.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The thermal-zone subnodes we defined for the A10 have underscores in them
that will generate DTC warnings. Change those underscores for hyphens.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.

Remove it in order to remove those warnings.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.

Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The USB power supply node in the AXP209 DTSI is using underscores in its
node name, which is generating a warning. Change those underscores for
hyphens.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.

Remove all these useless zeros that generate warnings
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Banana Pi M2 Ultra is an SBC based on the Allwinner V40 SoC (same as
the R40 SoC). The form factor is similar to the Raspberry Pi series.

It features:

- X-Powers AXP221s PMIC connected to i2c0
- 1GiB DDR3 DRAM
- microSD slot
- MicroUSB Type-B port for power and connected to usb0
- HDMI output
- MIPI DSI connector
- 4 USB Type-A ports (connected to the usb1 controller via a hub)
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 module, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- audio out headphone jack
- red and green LEDs
- debug UART pins
- Raspberry Pi B+ compatible GPIO header
- power and reset buttons

This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Banana Pi M2 Ultra is an SBC based on the Allwinner R40 SoC. The
form factor and position of various connectors, leds and buttons is
similar to the Banana Pi M1+, Banana Pi M3, and is exactly the same
as the latest Banana Pi M64.

It features:

  - X-Powers AXP221s PMIC connected to i2c0
  - 2 GB DDR3 DRAM
  - 8 GB eMMC
  - micro SD card slot
  - DC power jack
  - HDMI output
  - MIPI DSI connector
  - 2x USB 2.0 hosts
  - 1x USB 2.0 OTG
  - gigabit ethernet with Realtek RTL8211E transceiver
  - WiFi/Bluetooth with AP6212 chip, with external antenna connector
  - SATA and power connectors for native SATA support
  - camera sensor connector
  - consumer IR receiver
  - audio out headphone jack
  - onboard microphone
  - red, green, and blue LEDs
  - debug UART pins
  - Li-Po battery connector
  - Raspberry Pi B+ compatible GPIO header
  - power, reset, and boot control buttons

This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner R40 SoC is marketed as the successor to the A20 SoC.
The R40 is a smaller chip than the A20, but features the same set
of programmable pins, with a couple extra pins and some new pin
functions. The chip features 4 Cortex-A7 cores and a Mali-400 MP2
GPU. It retains most if not all features from the A20, while adding
some new features, such as MIPI DSI output, or updating various
hardware blocks, such as DE 2.0.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

This patch fixes the warning "xxx has a unit name, but no reg property"
by removing "@0" from such node. 6 board files are fixed. Each has the
same aforementioned issue in pinmux nodes. These include the Nano Pi
family base dtsi file, the Orange Pi 2, Orange Pi Lite, Orange Pi One,
Orange Pi PC, and Orange Pi Plus.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Squashed 6 patches together; boards named in commit log]
Signed-off-by: NChen-Yu Tsai <wens@csie.org>