Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7790 device tree.

In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.

Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add r8a7793 GPIO device nodes that are assumed to be identical
to r8a7791. This matches the data sheet for GPIO and MSTP bits.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable the DU device and the VGA port available on the r8a7794
ALT board. The VGA portion of the ALT board is somewhat similar
to the Lager board but in case of ALT the DU1 pins are used
and the X2 clock has a reduced frequency.

This patch does not include any pinctrl (PFC) settings due to lack
of PFC DT integration on r8a7794. At this point the default state
of the boot loader is enough to keep the VGA port working without
changing any pinctrl settings.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU0 clock is an MSTP clock, child of the CPG ZX clock.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable the QSPI controller in the gose device tree.

Based on similar work for the silk board by Vladimir Barinov and
Sergei Shtylyov.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Instantiate the QSPI controller in the r8a7793 device tree.

Based on similar work for the r8a7794 by Hisashi Nakamura and
Sergei Shtylyov.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Instantiate the two system DMA controllers in the r8a7793 device tree.

Based on similar work for the r8a7793 by Laurent Pinchart.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

As of commits 5cfdedb7 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9 ("doc: dt: mtd: support
partitions in a special 'partitions' subnode"), having partitions as
direct subnodes of an mtd device is discouraged:

    spi0.0: 'partitions' subnode not found on /spi@e6b10000/flash@0. Trying to parse direct subnodes as partitions.

Hence move the SPI FLASH partitions to a "partitions" subnode.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Configure PFC for the already enabled scif and ethernet devices
in the device tree for the gose board.

Based on similar work for the koelsch board by Laurent Pinchart and
Sergei Shtylyov.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Instantiate PFC device in r8a7793 DT.

Based on similar work for the r8a7791 by Magnus Damm.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Instantiate the thermal sensor in the r8a7793 device tree.

Based on very similar work for the r8a7790 by Magnus Damm.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

The Henninger low cost board was never sold and so  had  no  users outside
Renesas (and Cogent Embedded). Instead Renesas  has made the Porter  board
which has mostly similar hardware. Now that the Porter board support is on
par with Henninger, we can remove  the Henninger's device tree file.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the Porter board dependent part of the CAN0 device node.

This patch is  analogous to the commit 457acc4a ("ARM: shmobile:
henninger: add CAN0 DT support") as there are no differences between the
boards in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add IPMMU nodes for the r8a7793 SoC. The IPMMU configuration for r8a7793
is identical to r8a7791 and includes SY0, SY1, DS, MP, MX, RT and GP.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The r8a7794 IPMMU nodes for MX and DS are currently lacking
a line containing 'status = "disabled"', fix this by
making sure they are disabled like all other IPMMU nodes.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

On R8A7791, GPIO banks 1 and 7  are missing  pins 26 to 31.  Correct the
"gpio-ranges" properties of the GPIO1 node (GPIO7 is already correct).
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

On R8A7790, GPIO banks 1 and 2 are missing  pins 30 and 31.  Correct the
"gpio-ranges" properties of the corresponding device nodes.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.

This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the SILK board dependent part of the SDHI1 (connected to micro-SD
slot) device nodes along with the necessary voltage regulators.

Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

R-Car M2-W does not have an IMP core or an IMP clock.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

R-Car E2 does not have an IMP core or an IMP clock.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable HS-USB device  for the Porter board, defining the GPIO that the
driver should check  when probing (which is the ID output from MAX3355
OTG chip).

Note that there  will be pinctrl-related error messages if both internal
PCI  and  HS-USB drivers are enabled but they should be just ignored.

This patch is  analogous  to the commit 6f4f7156 ("ARM: shmobile:
henninger: enable HS-USB") as there  are no differences between the
boards in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable  internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached
to them and also enable  USB PHY device  for the Porter board.  We have to
enable  everything in one patch since EHCI/OHCI devices are already linked
to the USB PHY device.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable the PCIe controller and clock for the Porter board.

This patch is analogous to the commit 485f3ce6 ("ARM: shmobile:
henninger: Enable PCIe Controller & PCIe bus clock") as there are no
differences between the boards in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the Porter board dependent part of the QSPI device node.
Add device nodes  for Spansion  S25FL512S SPI flash and the MTD partitions
on it.

This patch is  mostly analogous  to the commit f59838d4 ("ARM:
shmobile: henninger: add QSPI DT support")  as there are no differences
between the boards in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the  Porter board dependent part of the VIN0 device node.
Add the device node for Analog Devices  ADV7180 video decoder to I2C2 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.

This patch is  analogous to the commit 8d62f4f7 ("ARM: shmobile:
henninger: add VIN0/ADV7180 DT support") as there are no differences
between the boards in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the Porter board dependent part of the I2C2 device node.

This patch is  analogous to the commit 29a647c3 ("ARM: shmobile:
henninger: add I2C2 DT support") as there are no differences between
the boards in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable SATA0 device for the Porter board.

This patch is analogous to the commit 5a62ec57 ("ARM: shmobile:
henninger: enable SATA0") as there are no differences between the boards
in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the Porter board dependent part of the SDHI0/2 device nodes along
with the  necessary  voltage regulators (note that the Vcc regulators are
dummy -- they are required but don't actually exist on the board). Also,
GPIOs have to be used for the CD and WP signals due to the SDHI driver
constraints...

This patch is analogous to the commit 1299df03 ("ARM: shmobile:
henninger: add SDHI0/2 DT support") as there  are no differences between
those boards in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define  the Porter board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.

This  patch  is analogous to the commit 26b0d2cf ("ARM: shmobile:
henninger: add Ether DT support") as there  are no differences between
those boards in this respect.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Unfortunately, the SILK board bindings were not quite correct, as the  board
name should be all caps.  Fix that,  adding the board model #  in parens and
removing stray semicolon.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the R8A7794 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The Mitsubishi AA121TD01 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the SILK board.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the R8A7794 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the initial device tree for the R8A7791 SoC based Porter low cost board
(which  is a  slightly modified version  of the Henninger board).

SCIF0 serial port support is included, so that the serial console can work.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add Porter device tree bindings documentation, listing it as a supported board.

This allows to use checkpatch to validate DTSes referring to the Porter board.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>