sil164 and friends are the most common, usually they just need to be
poked once because a fixed configuration is enough for any modes and
clocks, so they worked without this patch if the BIOS had done a good
job on POST. Display couldn't survive a suspend/resume cycle though.
Unfortunately, BIOS scripts are useless here.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Locking only makes sense in the VBIOS parsing code as it's executed
before CRTC init.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Clean up and move the external TV encoder detection code to
nouveau_i2c.c, it's also going to be useful for external TMDS and DDC
detection.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Rescaling interlaced modes isn't going to work correctly, and even if
it did, come on, interlaced flat panels? are you pulling my leg?
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Based on a patch from Matthew Garrett.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Acked-by: NMatthew Garrett <mjg@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Load detection needs the connector wired to a CRTC, when there are no
inactive CRTCs left that means we need to cut some other head off for
a while, causing intermittent flickering.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Create connectors before encoders to avoid having to do another loop across
encoder list whenever we create a new connector.  This allows us to pass
the connector to the encoder creation functions, and avoid using a
create_resources() callback since we can now call it directly.

This can also potentially modify the connector ordering on nv50.  On cards
where the DCB connector and encoder tables are in the same order, things
will be unchanged.  However, there's some cards where the ordering between
the tables differ, and in one case, leads us to naming the connectors
"wrongly".
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

fixes oops in nouveau_connector_get_modes with nv_encoder is NULL
Signed-off-by: NAlbert Damen <albrt@gmx.net>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

a7b9f9e5adef dropped it by accident.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Tested-by: NThibaut Girka <thib@sitedethib.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

When selecting the native mode for a display we weren't taking into account
whether or not it was actually supported on that particular output.

This patch modifies our native mode selection to run all modes through
mode_valid() first.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It was once assumed that all G8x had dual-link TMDS everywhere, this isn't
actually the case - especially considering passive DP->DVI converters and
some HDMI connectors only support single-link.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

When CONFIG_ACPI_BUTTON=m (and probably when ACPI_BUTTON is not enabled)
and NOUVEAU is built-in (not as a loadable module):

nouveau_connector.c:(.text+0xe17ce): undefined reference to `acpi_lid_open'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.

v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.

v3: add config lock take inside polling, add intel/nouveau poll init/fini calls

v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.

glisse: discard drm_helper_hpd_irq_event

v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Intended to be used as a workaround in cases where we falsely detect
that a TV is connected when it's not.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This is in preference to disconnected.  If there's no other outputs
connected this will cause LVDS to be programmed even with the lid
closed rather than having X fail to start because of no available
outputs.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This makes this code common to both the nv04 and nv50 paths.

For the moment, we keep the previous behaviour with HDMI/eDP connectors
and report them as DVI-D/DP instead.  This will be fixed once the rest
of the code has been fixed to deal with those types.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMaarten Maathuis <madman2003@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Also adds a module option to ignore the status reported via ACPI, in case
we hit systems with broken ACPI.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This was spotted by kmemleak.
Signed-off-by: NXavier Chantry <shiningxc@gmail.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

- Use driver level (0x2) for NV_DEBUG instead of all levels
- Create a NV_DEBUG_KMS for KMS level (0x4) and use them in modesetting code
- Remove a few odd NV_TRACE calls and replace some of them with NV_DEBUG_KMS or
NV_INFO
Signed-off-by: NMaarten Maathuis <madman2003@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This adds a drm/kms staging non-API stable driver for GPUs from NVIDIA.

This driver is a KMS-based driver and requires a compatible nouveau
userspace libdrm and nouveau X.org driver.

This driver requires firmware files not available in this kernel tree,
interested parties can find them via the nouveau project git archive.

This driver is reverse engineered, and is in no way supported by nVidia.

Support for nearly the complete range of nvidia hw from nv04->g80 (nv50)
is available, and the kms driver should support driving nearly all
output types (displayport is under development still) along with supporting
suspend/resume.

This work is all from the upstream nouveau project found at
nouveau.freedesktop.org.

The original authors list from nouveau git tree is:
Anssi Hannula <anssi.hannula@iki.fi>
Ben Skeggs <bskeggs@redhat.com>
Francisco Jerez <currojerez@riseup.net>
Maarten Maathuis <madman2003@gmail.com>
Marcin Kościelnicki <koriakin@0x04.net>
Matthew Garrett <mjg@redhat.com>
Matt Parnell <mparnell@gmail.com>
Patrice Mandin <patmandin@gmail.com>
Pekka Paalanen <pq@iki.fi>
Xavier Chantry <shiningxc@gmail.com>
along with project founder Stephane Marchesin <marchesin@icps.u-strasbg.fr>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>