ARM patch 3756/1 added HWCAP_IWMMXT.  This patch adds support
for broadcasting that info via /proc/cpuinfo and sets it for
the CPU features of the PXA270.

I've booted 19rc3 on a pxa270 and confirmed that the /proc/cpuinfo
shows "iwmmxt" in the Features.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On stepping A0/A1 of the 80200, invalidating D-cache by line doesn't
clear the dirty bits, which means that if we invalidate a dirty line,
the dirty data can still be written back to memory later on.

To work around this, dma_inv_range() on these two processors is
implemented as dma_flush_range() (i.e. do a clean D-cache line before
doing the invalidate D-cache line.)  For this, we currently have a
processor ID check in xscale_dma_inv_range(), but a better solution
is to add a separate cache_fns and proc_info for A0/A1 80200.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Dan Williams

commit a6a38a66 changed the iop321 id to a value that does not work with all platforms.  Change the mask to permit bit 11.  Tested on an iq80321 600Mhz CRB.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

The IOP 80219 xscale CPU is a stripped down version of the IOP32x.
But the fact that the 80219 and IOP32x are very similar doesn't mean
that they need to share a cpu table entry.  It's also somewhat confusing
for the end user to see the 80219 reported as an IOP32x, so this patch
splits the IOP32x cpu table entry to make a separate entry for the
80219.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

According to the Intel PXA27x Processor Family Specification
Update document (doc.nr. 280071-009) erratum E7, some care must be taken
to locate the disabling and re-enabling of the MMU to the beginning of a
cache line to avoid problems in some circumstances.

Credits to Simon Vogl <simon.vogl@researchstudios.at> for bringing this
up.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On some CPUs, bit 4 of section mappings means "update the
cache when written to".  On others, this bit is required to
be one, and others it's required to be zero.  Finally, on
ARMv6 and above, setting it turns on "no execute" and prevents
speculative prefetches.

With all these combinations, no one value fits all CPUs, so we
have to pick a value depending on the CPU type, and the area
we're mapping.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Most MMU-based CPUs have a restriction on the setting of the data cache
enable and mmu enable bits in the control register, whereby if the data
cache is enabled, the MMU must also be enabled.  Enabling the data
cache without the MMU is an invalid combination.

However, there are CPUs where the data cache can be enabled without the
MMU.

In order to allow these CPUs to take advantage of that, provide a
method whereby each proc-*.S file defines the control regsiter value
for use with nommu (with the MMU disabled.)  Later on, when we add
support for enabling the MMU on these devices, we can adjust the
"crval" macro to also enable the data cache for nommu.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

asm/hardware.h is not required for the majority of processor support
files, ioremap support, mm initialisation, acorn IO support, nor
the debug code (which picks up its machine specific includes via
debug-macros.S)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the hardware PMD and PTE page table definitions from pgtable.h
into pgtable-hwdef.h, and include pgtable-hwdef.h as necessary.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

The mini I-cache issue is valid only for kernel space since debuggers
would not fly if they used user space addresses for their stubs.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The `make buildcheck` is erroneously reporting that the .proc.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Deepak Saxena

The XScale locking code is not something that has been validated
on 2.6 and needs to be replaced with a more generic API to use
with other ARMs that support locking features.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!