This is to prepare the suspend/resume improvement in next patch. The
SW parts can be optimized out during resume.

As for rxq handling during suspend, we'd like to drop packets by
calling mvneta_rxq_drop_pkts() which is both SW and HW operation,
so we don't split rxq deinit.
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bgmac_dma_tx_ring_free() assigns the ctl1 word which is a litle endian
32-bit word without using proper accessors, fix this, and because a
length cannot be negative, use unsigned int while at it.

Fixes: 9cde9450 ("bgmac: implement scatter/gather support")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the members: base, idm_base and nicpm_base should be annotated with
__iomem since they are pointers to register space. This fixes a bunch of
sparse reported warnings.

Fixes: f6a95a24 ("net: ethernet: bgmac: Add platform device support")
Fixes: dd5c5d03 ("net: ethernet: bgmac: add NS2 support")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mdio-bitbang mentioned 10 for both read and write.
However mdio read opcode is 10 and write opcode is 01
Fixed comment.
Signed-off-by: NFrans Meulenbroeks <fransmeulenbroeks@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sky2 ethernet stops working after system resume from suspend:
[ 582.852065] sky2 0000:04:00.0: Refused to change power state, currently in D3

The current 150ms delay is not enough, change it to 200ms can solve the
issue.

BugLink: https://bugs.launchpad.net/bugs/1758507
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default TX moderation mode was mistakenly set to CQE based. The
intention was to add a control ability in order to improve some specific
use-cases. In general, we prefer to use EQE based moderation as it gives
much better numbers for the common cases.

CQE based causes a degradation in the common case since it resets the
moderation timer on CQE generation. This causes an issue when TSO is
well utilized (large TSO sessions). The timer is set to 16us so traffic
of ~64KB TSO sessions per second would mean timer reset (CQE per TSO
session -> long time between CQEs). In this case we quickly reach the
tcp_limit_output_bytes (256KB by default) and cause a halt in TX traffic.

By setting EQE based moderation we make sure timer would expire after
16us regardless of the packet rate.
This fixes an up to 40% packet rate and up to 23% bandwidth degradtions.

Fixes: 0088cbbc ("net/mlx5e: Enable CQE based moderation on TX CQ")
Signed-off-by: NTal Gilboa <talgi@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver is closed, all the associated irqs are disabled. In the
event that the driver exits a reset in the closed state, we should be
consistent with the state we are in directly after a close. So before we
exit the reset routine, all irqs should be disabled as well. This will
prevent the irqs from being enabled twice in this case and reporting a
number of noisy warning traces.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QCA Rome controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: NVic Wei <vwei@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove including <linux/version.h> that don't need it.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

As Interrupt resource specified IRQs are now assumed to be always
active-low the DMI quirk for the MINIX Z83-4 is no longer required.
Signed-off-by: NIan W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Iff TSU registers exist on a given [G]Ether controller, they always include
the CAM entry table registers (TSU_ADR{H|L}<n>), thus the check for invalid
TSU_ADRH0 offset in __sh_eth_get_regs() is useless...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 6ded2865 ("sh_eth: Fix RX recovery on R-Car in case of RX
ring underrun") added a check for an bad RDFAR offset in sh_eth_rx(), so
that the code could work on the R-Car Ether controllers which don't have
this register (and TDFAR), then the commit 3365711d ("sh_eth: WARN on
access to a register not implemented in a particular chip") replaced
offset 0 with 0xffff. Adding/checking the 'no_xdfar' bit field in the
'struct sh_eth_cpu_data' instead results in less object code...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit cf29bded.

It causes regressions.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refine the RX check summing handling to propagate the
hardware provided checksum so that we do not have to
compute it later in software.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 14530746 ("devlink: Remove top_hierarchy arg to
devlink_resource_register"), the "top_hierarchy" parameter to
devlink_resource_register() was removed in favor of using the parameter
"parent_resource_id" exclusively to determine who the parent is. The
root node's resource ID for this purpose is
DEVLINK_RESOURCE_ID_PARENT_TOP with the value 0. It is therefore
problematic that the resource MLXSW_SP_RESOURCE_KVD has also ID of 0.

Fix this by numbering driver-specific resources from 1.

Fixes: 14530746 ("devlink: Remove top_hierarchy arg to devlink_resource_register")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass struct mlxsw_core instead of devlink since it is nicer within mlxsw
code and we need both structs in mlxsw_sp_kvdl_resources_register()
anyway.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As struct mlxsw_config_profile is mapped to the payload of the FW
command of the same name, resources_query_enable flag does not belong
there. Move it to struct mlxsw_driver.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check should be done directly in mlxsw_pci_config_profile, as for
other profile items. Also, be consistent in naming with the rest and
rename to "used_kvd_sizes".
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First arg of these helpers should be "mlxsw_core".
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should not be part of the struct, as the struct fields
are tightly coupled with the FW command payload of the same name.
Just use the "granularity" define directly, as in other places.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The parts info is array. The parts copy this info array, yet they are a
list. So make the indexing according to the id and change the list of
parts into array of parts. This helps to eliminate lookups and
constructs like mlxsw_sp_kvdl_part_update() (took me some non-trivial
time to figure out what is going on there).
Alongside with that, introduce a helper macro to define the parts infos.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

devlink_resource_ops should be const as the arg of register function is
also const.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current code uses global variables, adjusts them and passes pointer down
to devlink. With every other mlxsw_core instance, the previously passed
pointer values are rewritten. Fix this by de-globalize the variables.

Fixes: 7f47b19b ("mlxsw: spectrum_kvdl: Add support for per part occupancy")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix copy&paste error in flex actions header ifndef define construct
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With patch 279c9361 the btuart_cs driver has been deprecated in
favor of serial_cs + hci_uart combination.

  static struct pcmcia_device_id btuart_ids[] = {
         /* don't use this driver. Use serial_cs + hci_uart instead */
         PCMCIA_DEVICE_NULL
  };

Intead of keeping it around, just remove it since it is not even
assigned to any PCMCIA identifiers anymore.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When adding the alignment and padding support for H:4 packet processing
for the Nokia driver, it broke the h4_recv_buf usage within bpa10x
driver. To fix this use a separate helper function and placing it into a
dedicated h4_recv.h header file.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The HCILL or eHCILL protocol from TI is actually an H:4 protocol with a
few extra events and thus can also use the h4_recv_buf helper. Instead
of open coding the same funtionality add the extra events to the packet
description table and use h4_recv_buf.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Now that we need just an ACPI HID in the table, and the driver auto-
configures itself otherwise, we can easily add a bunch of known ACPI HIDs.

This avoids having to add these 1 by 1 as devices with one are encountered
by users.

This commit may seem as if it simply adds all IDs between BCM2E00-BCM2EAC,
but that is not true, all these IDs were found in actual .inf files and
the range is not entirely continuous, the following IDs are not added:
BCM2E6A, BCM2E6C, BCM2E8F and BCM2E91 because I did not see these in any
.inf files. As for the large amount of IDs this seems to be caused by
Broadcom using a separate ID for every bluetooth module using their
chips. E.g. BCM2EA6 seems to be specifically for the Raspberry Pi 3.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since I've been doing a lot of work on Linux Bay Trail / Cherry Trail
support, I've gathered a collection of ACPI DSDTs from about 50 such
machines.

Looking at these DSTDs many have an ACPI device entry describing a bcm
bluetooth device (often disabled in the DSDT), quite a few of these ACPI
device entries have a resource-table where the order does not match with
the order currently associated with the HID of that entry in the
bcm_acpi_match table.

Looking at the Windows .inf files, there is nothing indicating a specific
order there, so I believe that there is no 1:1 mapping between the ACPI
HID and the order in which the resources are listed.

Therefor this commit replaces the hardcoded mapping based on ACPI HID,
with code which actually checks in which order the resources are listed
and bases the gpio-mapping on that.

This should ensure that we always pick the right mapping and this will
make adding new ACPI HIDs to the driver easier.

This has been tested on the following devices:
-Asus T100CHI           BCM2E39 / brcmfmac43241b4-sdio / BCM4324B3-37.4M.hcd
-Asus T100TA            BCM2E39 / brcmfmac43241b4-sdio / BCM4324B3-37.4M.hcd
-Asus T200TA            BCM2E65 / brcmfmac43340-sdio   / BCM43341B0-37.4M.hcd
-Jumper ezPad mini 3    BCM2E74 / brcmfmac43430a0-sdio / BCM4343A0-26M.hcd
-Acer Iconia Tab8 w1-8  BCM2E83 / brcmfmac4330-sdio    / BCM4330B1-26M.hcd
-Chuwi Vi8 plus(CWI519) BCM2EAA / brcmfmac43430-sdio   / BCM43430A1-26M.hcd

Which together cover all 3 combinations of using an Interrupt resource /
GpioInt resource as first resource / GpioInt resource as last resource.
Tested-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We declare the same set of const acpi_gpio_params twice with different
names, besides the needless duplication this naming leads to a sortof
double indirection which also makes it harder to see how the mapping is
actually setup.

This commit renames the first set to have generic names, which better
describe the contents of the mapping and drops the second set.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add 6 new ACPI HIDs to enable bluetooth on devices using these HIDs,
I've tested the following HIDs / devices:

BCM2E74: Jumper ezPad mini 3
BCM2E83: Acer Iconia Tab8 w1-810
BCM2E90: Meegopad T08
BCM2EAA: Chuwi Vi8 plus (CWI519)

The reporter of Red Hat bugzilla 1554835 has tested:
BCM2E84: Lenovo Yoga2

The reporter of kernel bugzilla 274481 has tested:
BCM2E38: Toshiba Encore

Note the Lenovo Yoga2 and Toshiba Encore also needs the earlier patch to
treat all Interrupt ACPI resources as active low.

Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/attachment.cgi?id=274481
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835Reported-and-tested-by: NRobert R. Howell <rhowell@uwyo.edu>
Reported-and-tested-by: NChristian Herzog <daduke@daduke.org>
Tested-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Older devices with a serdev attached bcm bt hci, use an Interrupt ACPI
resource to describe the IRQ (rather then a GpioInt resource).

These device seem to all claim the IRQ is active-high and seem to all need
a DMI quirk to treat it as active-low. Instead simply always assume that
Interrupt resource specified IRQs are always active-low.

This fixes the bt device not being able to wake the host from runtime-
suspend on the: Asus T100TAM, Asus T200TA, Lenovo Yoga2 and the Toshiba
Encore, without the need to add 4 new DMI quirks for these models.

This also allows us to remove 2 DMI quirks for the Asus T100TA and Asus
T100CHI series. Likely the 2 remaining quirks can also be removed but I
could not find a DSDT of these devices to verify this.

Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=198953
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add irq_polarity module option for easier troubleshooting of irq-polarity
issues.

Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This WiFi/Bluetooth USB dongle uses a Realtek chipset, so, use btrtl for it.

Product information:
https://wikidevi.com/wiki/Edimax_EW-7611ULB

From /sys/kernel/debug/usb/devices
T:  Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=7392 ProdID=a611 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=Edimax Wi-Fi N150 Bluetooth4.0 USB Adapter
S:  SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 6 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723bu
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=500us
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Tested-by: NVicente Bergas <vicencb@gmail.com>
Signed-off-by: NVicente Bergas <vicencb@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The struct hcill_cmd to create an skb with a single u8 is pointless. So
just use skb_put_u8 instead.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The variable "payload" will eventually be set to an appropriate pointer
a bit later. Thus omit the explicit initialisation at the beginning.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In case the shutdown GPIO is not wired up, it is impossible to reset the
Bluetooth controller to its original state. This include the initial
default baud rate which leads to issues when reloading the module or
when something unexpected happens. To avoid any kind of runtime
deadlocks, stick with the initial default baud rate.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some GPIO controller drivers request sleepable context and so can't
be accessed from IRQ context. Using gpiod_set/get_value accessors
with such controller leads to a kernel warning since they are
reserved for atomic context (according to the documentation).

Use the postfixed _cansleep version instead, indicating that context
is safe for sleeping if necessary. Note that this is the case here
since we never toggle the gpio neither from IRQ nor from a spinlocked
section.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Entry for Inline TLS as another driver dependent on cxgb4 and chcr
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>