An udelay of 5 is sufficient for standard speed i2c busses, 10 make it
too slow.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Loading the firmware using the i2c bit-banging code blocks the kernel.
Move the firmware load code into a workqueue so that it plays well with
other processes.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

tcm825x.c: In function 'ioctl_try_fmt_cap':
tcm825x.c:639: warning: format '%d' expects type 'int', but argument 4
                                        has type 'long unsigned int'
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The Conexant cx23415 MPEG encoder/decoder supports some unusual pixelformats
for the On-Screen Display. Add new defines to videodev2.h for these formats.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Now dvb_powerdown_on_sleep controls whether
- whether LNB power is turned off
- whether the tuner/frontend enters sleep mode
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Default for dvb_shutdown_timeout set to 0.
dvb_shutdown_timeout > 0 is used for debugging only.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ts_bus_ctrl() should only be called by
- the first open
- the last release call.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

decrement module use count on error
Signed-off-by: NMarco Schluessler <marco@lordzodiac.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

return correct error code value
Signed-off-by: NMarco Schluessler <marco@lordzodiac.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

vmalloc() returns void * - no need to cast it.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Clean whitespace brain-damage caused by previous patch,
"Fix a warning at dvb_net"
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since kzalloc() returns a void pointer, we don't need to cast the
return value in drivers/media/video/ivtv/ivtv-queue.c
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ivtv: set correct pixel format and alpha properties in VIDIOC_G_FBUF
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Support for V4L2_ENC_CMD_STOP_AT_GOP_END was broken. While the driver
correctly waited for the card to capture until the GOP was complete,
afterwards the driver buffers were just flushed instead of waiting
for the application to read all the pending data.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- add guards
- remove unused header includes
- move card-specific stuff from ivtv-driver.h to ivtv-cards.h
- move YUV-specific stuff from ivtv-driver.h to ivtv-yuv.h
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The driver should now pass the 'busy' state of the device to the cx2341x 
module whenever controls are set or tried. -EBUSY will be returned if 
the device is busy and the user attempts to modify certain 'dangerous' 
controls. It concerns controls that change the audio or video 
compression mode and bitrates.

The cx88-blackbird and pvrusb2 drivers currently always pass '0' (not busy)
to the cx2341x, effectively keeping the old behavior for now.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Changing the VBI format requires a CX2341X_ENC_INITIALIZE_INPUT firmware
call. This can only be done if no capture is in progress. So return
-EBUSY if the encoder is busy.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Always clear when stopping the decoder
- Clear if the filehandle that is being close was used for UDMA_YUV output.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The driver has long claimed to support mmap, but it didn't work at all.  Some
of the dma buffer parameters weren't set, and since video_buf uses vmalloc to
allocate the buffer, a page callback is needed too.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The driver kepts a static global array of snd_card pointers for each card
probed, which was never used.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rework the way the DMA buffer is handled and IRQs are generated.

ALSA uses a ring-buffer of multiple periods.  Each period is supposed to
corrispond to one IRQ.

The existing driver was generating one interrupt per ring-buffer, as opposed
to per period.  This meant that as soon as the IRQ was generated, the hardware
was already starting to re-write the beginning of the buffer.  Since the DMA
happens on a per-line basis, there was only a narrow window to copy the data
out before the buffer was overwritten.

The cx88 core RISC program generator is modified so that it can set the IRQ
and counter flags to count every X lines of DMA transfer.  This way we can
generate an interrupt every period instead of every full ring-buffer.  Right
now only period of one line are supported, but it should be possible to
support longer periods.  Note that a WRITE instruction generates an IRQ when
it starts, not when the transfer is finished.  Thus to generate an IRQ when
line X is done, one must set the IRQ flag on the instruction that starts line
X+1, not the one that ends line X.

Change the line size so that there are four lines in the SRAM FIFO.  If there
are not four lines, the analog output from the cx88's internal DACs is full of
clicks and pops.

Try to handle FIFO sync errors.  Sometimes the chip generates many of these
errors before audio data starts.  Up to 50 sync errors will be ignored and the
counter reset.

Have the IRQ handler save the RISC counter to the chip struct, and then have
the pointer callback use this to calculate the pointer position.  We could
read the counter from the pointer callback, but sometimes the sync errors on
start up cause the counter to go crazy.  ALSA sees this and thinks there has
been an overrun.  The IRQ hander can avoid saving the counter position on
sync errors.

The chip "opened" flag wasn't necessary.  ALSA won't try to open the same
substream multiple times.  Probably this code was cut&pasted from the bt87x
driver, which has multiple sub-streams for one chip.

Do error checking for the videobuf mapping functions.

snd_card_cx88_runtime_free() is useless and can be deleted.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When the risc instrunctions from the CMDS were printed, instruction arguments
weren't taken into account.

This changes output like:
cx88[0]:   risc0: 0x1d010400 [ write sol eol irq1 cnt0 count=1024 ]
cx88[0]:   risc1: 0x0cac2800 [ INVALID sol eol 23 21 19 18 13 count=2048 ]
cx88[0]:   risc2: 0x1d010400 [ write sol eol irq1 cnt0 count=1024 ]
cx88[0]:   risc3: 0x0cac2c00 [ INVALID sol eol 23 21 19 18 13 count=3072 ]

cx88[0]:   risc0: 0x1d010400 [ write sol eol irq1 cnt0 count=1024 ]
cx88[0]:   risc1: 0x0cac2800 [ arg #1 ]
cx88[0]:   risc2: 0x1d010400 [ write sol eol irq1 cnt0 count=1024 ]
cx88[0]:   risc3: 0x0cac2c00 [ arg #1 ]
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Convert the initialization of ivtv_i2c_algo_template to C99-style.
Otherwise a future change to struct i2c_algo_bit_data would break
this code.

Also declared that structure const - it's a template after all.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This
patch removes all occurences of moduleparm.h from drivers/media files.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The file, tuner-driver.h was originally named tuner-hw.h, but we decided to
rename it.  At the time, I had forgotten to change the #ifdef __TUNER_HW_H__
to #ifdef __TUNER_DRIVER_H__ .  This patch corrects that.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add DVB-T support for Avermedia Super 007

Analog television is untested.  The device lacks input adapters for radio,
svideo & composite -- seems to be a DVB-T ONLY device.
Signed-off-by: NEdgar Simo <bobbens@gmail.com>
Acked-by: NHermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This is a simple whitespace cleanup.
Signed-off-by: NEdgar Simo <bobbens@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The revision is part of the pci_dev struct, so there is no need to read it in.

Stop storing the revision and latency in the chip struct, since they're never
used after being printed out when the driver loads.

linux/pci.h wasn't included.  It was getting picked up something else,
probably cx88.h, but this file uses struct pci_dev so it should include pci.h.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

channels_min should be 2, not 1.  The hardware only supports stereo.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Currently the driver turns on audio interrupts, then sets the audio interrupt
mask to select which interrupts to get.  One could received unwanted
interrupts since the mask is set _after_ interrupts have already been turned
on.  Change the order of the operations, and clear any audio interrupt status
bits that are already set for good measure.

Before changing the SRAM FIFO parameters, make sure the FIFO isn't being used.
This shouldn't happen with just the ALSA driver, as it should never try to
turn on FIFO/RISC/DMA while they are already on.  However, the V4L driver
needs to turn the audio FIFO on for analog audio output to work (undocumented
cx88 bug).  The FIFO parameters are in an inconsistent state while they are
updated, and this results in many FIFO sync error IRQs if the FIFO is in use
while it's in this inconsistent state.

Also create and use a bunch of symbolic constants for audio interrupt mask
bits.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>