This patch adds support to the ibm_emac driver for platform-specific
unsupported PHY features.

The patch attempts to determine the highest speed and duplex when
autonegotiation is unsupported.
Signed-off-by: NWade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The patch below is necessary to allow my Digital DS21143 Tulip rev 48
ethernet interface to work in a 10Mbit Half Duplex network.  Without
it, the driver keeps retrying other modes in an endless loop.  It seems
like someone already had the same problem with a rev 65 board :)
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

David S. Miller <davem@davemloft.net> wrote:
>I think removing support for older ifenslave binaries is
>the least painful solution to this problem.

	This patch removes backwards compatibility for old ifenslave
binaries (ifenslave prior to verison 1.0.0).

	I did not similarly modify ifenslave itself; with sysfs on the
horizon, I don't see that as being worthwhile.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The smc91c92_cs multicast does not work
if the count of multicast address is 1.

Signed-off-by: <komurojun-mbn@nifty.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix implicit nocast warnings in ns83820 code:
drivers/net/ns83820.c:603:46: warning: implicit cast to nocast type
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Skge driver was bringing link up/down when changing mac
address.  This doesn't work in the bonding environment, and is
more effort than needed.

Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=5271Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.

1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().

There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition.  I've marked it as such so that we remember to fix it.

This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test for VIA K8T800 north bridge instead of AMD K8 HyperTransport
bridge based on new information from Andi Kleen. The AMD
HyperTransport interface is not responsible for PCI transactions
and so the re-ordering is more likely done by the VIA north bridge.
This code is subject to change if we get more information from AMD
or VIA.

PCI Express devices are excluded from doing the read flush since all
chipsets in the write_reorder list are PCI chipsets.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Arrange for the initialisation printks to happen after we've
registered the network interface, so we know what name the
device is.  Also, check the link every 500ms (and use
msecs_to_jiffies.)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

EBSA110 link detection didn't read the register - it wrote it.  Oops.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Tone down the r8169 driver

As an alternative, people can use the boot time 'debug' option and/or use
'ethtool -s ethX msglvl xyz'.  The different messages are listed at:
http://www.zoreil.com/~romieu/r8169/doc/msglvl.txtSigned-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - __user annotations
 - NULL noise removal
 - C99 initializers
 - s/u32/pm_message_t/ in ->suspend()
 - removal of bogus casts in iounmap() arguments
 - if_mii() instead of open-coded variant

Remains to be done: ethtool conversion.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- __user annotations
- NULL noise removal
- C99 initializers
- s/u32/pm_message_t/ in ->suspend()
- removal of bogus casts in iounmap() arguments
- if_mii() instead of open-coded variant

Remains to be done: ethtool conversion.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A bunch of create_proc_dir_entry() calls creating directories had crept
in since the last sweep; converted to proc_mkdir().
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Latest wireless extensions moved a field from netdev -> wireless_handlers.
The WE core will now printk a warning on every call to get_wireless_stats()
on a driver that still uses the old field.  This patch fixes orinoco.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix interrupt test handler by adding check for IRQ assertion in
PCI_STATE register in addition to the status block updated bit.

Add test for valid ethernet address in tg3_set_mac_addr().

Add tg3_bus_string() to setup the PCI bus speed/width string for all
PCI/PCIX/PCI Express devices. This is used to print the bus type
during init_one().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 5780 PHY related problems:

1. MAC_RX_MODE reset must be done before setting up the MAC_MODE
   register on 5705_PLUS chips or the chip will stop receiving after
   a while. The MAC_RX_MODE reset is needed to prevent intermittently
   losing the first receive packet on serdes chips.

2. Skip MAC loopback test on 5780 because of hardware errata. Normal
   traffic including PHY loopback is not affected by the errata.

3. PHY loopback fails intermittently on 5708S and this is fixed by
   putting the PHY in loopback mode first before programming the MAC
   mode register. A MAC_RX_MODE reset is also added.

4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow
   nway_reset if 5780S is in parallel detect mode.

5. Add missing PHY IDs in KNOWN_PHY_ID() macro.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is one of those workarounds sucked over from sk98lin driver.
The skge driver needs to detect the Yukon-Lite A0 chip properly,
and turn of Rx FIFO Flush.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

While this is true, E8390_CMD is zero on i386, and thus there should be no
effect for these machines.  Machines like Mac, Amiga etc. which use Alan's
clever register mapping may have a non-zero E8390_CMD and result in bogus
"transmitter busy" type messages from this bug.

Fixes BUG# 3991.

vlan_hwaccel_rx should be used when in interrupt context.

Fixes bug  http://bugzilla.kernel.org/show_bug.cgi?id=5284Signed-off-by: NTommy S. Christensen <tommy.christensen@tpack.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cleanup receive buffer allocation and management,
Add more error handling checks from PHY and bump version.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Expand the returned data for ethtool debug access to include
all of the mapped PCI area; except for the small set of registers
that are for diagnostic RAM access. Access to those registers
will hang the system.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix bond_enslave link monitoring warning to check use_carrier status
and ethtool_ops in addition to do_ioctl.  This version checks ethtool_ops
as well as do_ioctl, and also uses the per-bond params.use_carrier
instead of the global use_carrier.
Signed-off-by: NJason R. Martin <nsxfreddy@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The following commit breaks cisco mode with my WAN drivers:
author	David S. Miller <davem@davemloft.net>
	Tue, 28 Jun 2005 22:25:31 +0000 (15:25 -0700)
commit	689be439

"[NET]: Remove gratuitous use of skb->tail in network drivers."

The following patch fixes it - please apply (cisco_hard_header does
skb_push(4 bytes)).
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Florin Malita <fmalita@gmail.com>

bond_init() is not releasing rtnl_sem after register_netdevice() and before
calling unregister_netdevice() (from bond_free_all()) in the exception
path.  As the device registration is not completed (dev->reg_state ==
NETREG_REGISTERING), the call to unregister_netdevice() triggers
BUG_ON(dev->reg_state != NETREG_REGISTERED).
Signed-off-by: NFlorin Malita <fmalita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix and simplify the workaround code for the 4GB boundary tx buffer
hardware bug.

1. Need to unmap the original SKB's dma addresses if a new SKB cannot
   be allocated.

2. Need to pass the base flag to tigon3_4gb_hwbug_workaround() or TSO
   won't work properly.

3. The guilty entry and length parameters for
   tigon3_4gb_hwbug_workaround() are removed as they are not necessary.

4. Remove assumption that only one fragment can hit the 4GB boundary.
   Another fragment can hit 8GB for example.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change 0 to NULL where appropriate.
Signed-off-by: NPeter Hagervall <hager@cs.umu.se>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thanks to Andy Stewart for the report and testing
debug patches from Michael Chan.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the driver work with any BladeCenter
network switch, it used to work only with certain
models.

Please apply.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Don't crash if ethtool statistics are requested and device is down.
Fix is to allocate pci space for statistics only when needed.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

	Bonding leaks route structures when the ARP monitor is
configured to send probes over VLANs.

	Originally reported by Ian Abel <ian.abel@mxtelecom.com>; his
original fix was modified by Jay Vosburgh to correct coding style and to
close a leak it missed.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Merge of four previous patches and the Kconfig fix
 * Remove debug printk's
 * whitespace cleanup and version number change
 * clear interrupts, reset phy, and reset hardware on shutdown
 * ignore 64bit counter overflow interrupts
 * fix a couple of places where second port could clobber state
   of first port.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Do not count frames dropped by the hardware as part of rx_dropped.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Do not count non-error frames dropped by the hardware as
part of rx_dropped. Instead, count those frames dropped as
rx_missed_errors. Also, do not count other error frames as part of
rx_dropped. Finally, do not count oversized frames in rx_dropped
(since they are counted as part of rx_length_errors).
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>