Add a warning if a child bus may be inaccessible because the
parent bridge has wrong secondary or subordinate bus numbers.
Note that this may or may not happen on "transparent" bridges,
as can be seen in bug #5557.

Also, if we do not fix up the assignment of bus numbers, try to
make use of the bus number space available.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes bugs in the pciehp driver that prevent hot-add
of a card with PCI bridges on it.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch disables power fault, MRL sensor and presence detection
interrupts when a PCIe slot is powered-off and enables those
interrupts when it is powered-on again. This is necessary to prevent
the associated events from causing an endless cycle of interrupts
due to the power-fault bit, which stays set till power is restored
to the slot.
Signed-off-by: NThomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've implemented a quirk to take advantage of the 1KB I/O space
granularity option on the Intel P64H2 PCI Bridge.  I had to change
probe.c because it sets the resource start and end to be aligned on 4k
boundaries (after the quirk sets them to 1k boundaries).  I've tested
this patch on a Unisys ES7000-600 both with and without the 1KB option
enabled.  I also tested this on a 2 processor Dell box that doesn't have
a P64H2 to make sure there were no negative affects there.
Signed-off-by: NDan Yeisley <dan.yeisley@unisys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The following patch implements .get_address callback of
hotplug_slot_ops for SHPCHP driver. With this patch, we
can see bus address of hotplug slots as follows:

	$ cat address
	0000:0b:01
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The RPAPHP code contains two routines that appear to be gratuitous copies
of very similar pci code.  In particular,

   rpaphp_claim_resource ~~ pci_claim_resource
      (there is a minor, non-functional difference)

   rpadlpar_claim_one_bus == pcibios_claim_one_bus
      (the code is identical)

This patch removes the rpaphp versions of the code.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Acked-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The RPAPHP code contains a routine that duplicates some existing code.
This patch removes the rpaphp version of the code.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Acked-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Updated printk and DBG with appropriate KERN_*.
Signed-off-by: NDaniel Marjamki <daniel.marjamaki@comhem.se>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current SHPCHP driver uses msleep_interruptible() function to wait for
a command completion event. But I think this would cause an unnecessary
long wait until timeout, if command completion interrupt came before
task state was changed to TASK_INTERRUPTIBLE. This patch fixes this
issue. With this patch, command completion becomes faster as follows:

o Without this patch

	# time echo 1 > power

	real    0m4.708s
	user    0m0.000s
	sys     0m0.524s

o With this patch

	# time echo 1 > power

	real    0m2.221s
	user    0m0.000s
	sys     0m0.532s
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current SHPCHP driver writes a '0' to the Command Completion Detect
bit to clear the Command Complete Interrupt Pending. But according to
the SHPC spec (See 4.7.3.1 System Interrupts), SHPCHP driver must
write '1'. This patch fixes this bug.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current SHPCHP driver seems not to map MMIO region properly. This
patch fixes this bug. This patch also cleanup the code.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The hpc_get_mode1_ECC_cap() function of SHPCHP driver seems to refer
the wrong bit for refering the "Mode 1 ECC Capability" bit. This bug
seems not to cause any problem so far. But I think this should be
fixed. This patch fixes this bug.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The hpc_get_max_bus_speed() function of the SHPCHP driver seems to
refer wrong bits in the "Slot Avail Register I" and "Slot Avail
Register II". This patch fixes this bug. And this also cleanup the
code.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch replaces pci_find_slot() with pci_get_slot() in the SHPCHP
driver. This enables SHPCHP driver to work on multiple PCI segment
systems.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Coverity checker spotted that we already did return -ENOMEM
if (!p_mem_node).
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed what appears to be a cut/paste error in
drivers/pci/hotplug/ibmphp_pci.c:
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bus_id string must be unique for all devices of that bus in the
system, not just for devices with the same parent - otherwise multiple
symlinks with identical names appear in /sys/bus/pci_express/devices.
Signed-off-by: NSergey Vlasov <vsu@altlinux.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NHanna Linder <hannal@us.ibm.com>
Signed-off-by: NMaximilian Attems <janitor@sternwelten.at>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
 arch/ppc/kernel/pci.c |   21 +++++++++++----------
 1 file changed, 11 insertions(+), 10 deletions(-)

Signed-off-by: NJiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Call pci_read_irq() for bridges too, so that the pin value
is stored for bridges that require interrupts.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the stored value of the interrupt pin rather than try to read
the config again.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the stored value of the Interrupt Pin, rather than try to read
it again.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Store the value of the INTERRUPT_PIN in the pci_dev structure
so that it can be retrieved later.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a major update to the cyblafb framebuffer driver. Most
of the stuff has been tested in the mm tree.

Main advantages:
============
  - vxres > xres support
  - ywrap and xpan support
  - much faster for almost all modes (e.g. 1280x1024-16bpp
     draws more than 41 full screens of text instead of about 25
     full screens of text per second on authors Epia 5000)
  - module init/exit code fixed
  - bugs triggered by console rotation fixed
  - lots of minor improvements
  - startup modes suitable for high performance scrolling
     in all directions

This diff  also contains a lot of white space fixes.

No side effects are possible, only one single graphics core is affected.
Signed-off-by: NKnut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fixed oops after failed netlink socket creation.

Wrong parathenses in if() statement caused err to be 1,
instead of negative value.

Trivial fix, not trivial to find though.
Signed-Off-By: NDmitry Mishin <dim@sw.ru>
Signed-Off-By: NKirill Korotaev <dev@openvz.org>
Signed-Off-By: NLinus Torvalds <torvalds@osdl.org>

__rcu_pending() is rather fat and called twice from rcu_pending().

rcu_pending() has multiple callers, and not that small too.

This patch uninlines both of them.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Acked-by: NPaul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Manual merge for trivial #include changes

This patch allows ipw2100 driver to advertise the WPA-related encryption
options that it does really support.  It's necessary to work correctly
with NetworkManager and other programs that actually check driver & card
capabilities.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

These warnings are emitted if non-modular network drivers are built.
Fixes just move cleanup_card() definitions into #ifdef MODULE region.

/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/wd.c:131: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/3c503.c:152: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/ne.c:216: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/hp.c:106: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/hp-plus.c:142: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/smc-ultra.c:172: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/e2100.c:144: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/es3210.c:159: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/lne390.c:149: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/lance.c:313: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/ac3200.c:127: warning: 'cleanup_card' defined but not used
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This contains a bug fix for large buffers.  Originally, if a tx buffer to
be sent was larger then the maximum size of the tx descriptor, it would
overwrite other control bits.  In this patch, the buffer is split over
multiple descriptors.  Also, the fragments are now setup in forward order.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NManfred Spraul <manfred@colorfullife.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Remove bouncing mail address of mv643xx maintainer.
Signed-off-by: NOlaf Hering <olh@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>