By storing the previous T6 status byte multiple debug output of the same
status can be suppressed (for example CFGERR).
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The T5 object may have various sizes depending on the objects used on the
particular maXTouch chip and firmware version, therefore it can't be
hardcoded in the driver. Allocate a buffer on probe instead.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The MXT device may be in bootloader mode on probe, due to:
1) APP CRC failure, either:
  a) flash corruption
  b) bad power or other intermittent problem while checking CRC
2) If the device has been reset 10 or more times without accessing comms
3) Warm probe, device was in bootloader mode already

This code attempts to recover from 1(b) and 3.

There is an additional complexity: we have to try two possible bootloader
addresses because the mapping is not one-to-one and we don't know the exact
model yet.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Later chips (for example mXT1664S) different mappings for bootloader
addresses.  This means that we must look at the family ID to determine
which address to use.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

On a warm probe, the device might be in a state where an flash operation was
not completed.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

If the bootloader on the touchscreen controller fails to initialise the
firmware image, it stays in bootloader mode and reports a failure. It is
possible to reflash a working firmware image from this state.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

By validating the checksum, we can identify if the configuration is
corrupt.  In addition, this patch writes the configuration in a short
series of block writes rather than as many individual values.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The existing implementation which encodes the configuration as a binary
blob in platform data is unsatisfactory since it requires a kernel
recompile for the configuration to be changed, and it doesn't deal well
with firmware changes that move values around on the chip.

Atmel define an ASCII format for the configuration which can be exported
from their tools. This patch implements a parser for that format which
loads the configuration via the firmware loader and sends it to the MXT
chip.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Touchpads are pointers, so make sure to pass the correct values to
input_mt_report_pointer_emulation(). Without this, tap-to-click doesn't
work.
Signed-off-by: NBenson Leung <bleung@chromium.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It is useful to initialise the input device later:
- Screen parameters may not be not known yet, for instance if waiting for
  firmware loader to return.
- Device may be in bootloader mode on probe (but could still be recovered by
  firmware download).

In addition, later devices have a different touchscreen object (T100) which
requires handling differently.

This also reduces the complexity of the probe function.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The maXTouch chips use the CHG line to generate status events in bootloader
mode, and during configuration download, before there is enough information
to configure the input device. Therefore set up the interrupt handler
earlier.

However, this introduces states where parts of the interrupt processing
must not run. Use data->object_table as a way to tell whether the chip
information is valid, and data->input_dev as a way to tell whether it is
valid to generate input report.
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NBenson Leung <bleung@chromium.org>
Acked-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This ioctl is the counterpart to EVIOCGVERSION and returns the
uinput-version the kernel was compiled with.
Reviewed-by: NPeter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This moves basic checks and setup from uinput_setup_device() into
uinput_validate_absbits() to make it easier to use. This way, we can call
it from other places without copying the boilerplate code.
Reviewed-by: NPeter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It's possible that the controller has an individually switchable power supply.
Therefore add support to control a supplying regulator.

As this is not always the case, the regulator is requested as optional.
Signed-off-by: NHeiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Recent version of xf86-input-wacom no longer support directly accessing
serial tablets. Instead xf86-input-wacom now expects all wacom tablets to
be driven by the kernel and to show up as evdev devices.

This has caused old serial Wacom tablets to stop working for people who still
have such tablets. Julian Squires has written a serio input driver to fix this:
https://github.com/tokenrove/wacom-serial-iv

This is a cleaned up version of this driver with improved Graphire support
(I own an old Graphire myself).
Signed-off-by: NJulian Squires <julian@cipht.net>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch introduces the use of managed interfaces like devm_kzalloc,
devm_input_allocate_device, devm_request_threaded_irq etc. and does away
with the calls to free the allocated memory. The remove function is no
longer required and is completely done away with. Also, the labels in the
probe function are removed.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds a driver for Microchips CAP1106, an I2C driven, 6-channel
capacitive touch sensor.

For now, only the capacitive buttons are supported, and no specific
settings that can be tweaked for individual channels, except for the
device-wide sensitivity gain. The defaults seem to work just fine out of
the box, so I'll leave configurable parameters for someone who's in need
of them and who can actually measure the impact. All registers are
prepared, however. Many of them are just not used for now.

The implementation does not make any attempt to be compatible to platform
data driven boards, but fully depends on CONFIG_OF.

Power management functions are also left for volounteers with the ability
to actually test them.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Fix checkpatch warning:
"WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required"
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The patch e57a66aa: "Input: atmel_mxt_ts - read and report
bootloader version" from May 18, 2014, leads to the following static
checker warning:

	drivers/input/touchscreen/atmel_mxt_ts.c:437 mxt_get_bootloader_version()
	warn: signedness bug returning '(-5)'

drivers/input/touchscreen/atmel_mxt_ts.c
   429  static u8 mxt_get_bootloader_version(struct mxt_data *data, u8 val)
   430  {
   431          struct device *dev = &data->client->dev;
   432          u8 buf[3];
   433
   434          if (val & MXT_BOOT_EXTENDED_ID) {
   435                  if (mxt_bootloader_read(data, &buf[0], 3) != 0) {
   436                          dev_err(dev, "%s: i2c failure\n", __func__);
   437                          return -EIO;
                                       ^^^^
This gets truncated into a number from 0-255 and anyway the caller
doesn't check for errors.

(reported by Dan Carpenter)
Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's start checking return value of regulator_enable and pwm_enable to
avoid errors. Fixes the following warning:

drivers/input/misc/max8997_haptic.c:185:19: warning: ignoring return value of ‘regulator_enable’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).

I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151

To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: NJames Lademann <jwlademann@gmail.com>
Tested-by: NPhilipp Wolfer <ph.wolfer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:

https://bugzilla.redhat.com/show_bug.cgi?id=1103528

This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.

It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.

Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.

So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: NElder Marco <eldermarco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The driver sends 3 bytes instead of 2 when accessing a register on the M09
firmware, so writing to gain seems to overflow into the offset register.
Signed-off-by: NRobert Woerle <robert@linuxdevelopment.de>
Acked-By: NSimon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This is unused since all users (OMAP4/5) are DT only.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This has been unused since omap4 board files went away.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

New Cintiq tablets have a 200 tablet counts outside of screen area.
Add x/y_min for ABS_X/Y to pass this information to userland.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This adds support for the tsc2005 touchscreen
to the Nokia N900 DTS file.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.

The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>