This is a new driver for Aztech Sound Galaxy ISA soundcards based on the
AZT1605 and AZT2316 chipsets. It's constructed as two seperate drivers
for either chipset generated from the same source file, with (very)
minimal ifdeffery.

The drivers check the SB DSP version to decide if they are being loaded
for the right chip. AZT1605 returns 2.1 by default and AZT2316 3.1.
This isn't full-proof as the DSP version can actually be set through
software but it's close enough -- as far as I've been able to see, the
DSP version can not be stored in the EEPROM and the cards will therefore
startup with the defaults.

This distinction could (with the same success rate) also be used to
decide which chip we're looking at at runtime meaning a single, merged
driver is also an option but I feel it's actually nicer this way. A
merged driver would have to postpone translating the passed in resource
values to the card configuration until it knew which one it was looking
at and would need to postpone erring out on mpu_irq=10 for azt1605 and
mpu_irq=3 for azt2316.

The drivers have been tested on various cards. For snd-azt1605:

FCC-ID I38-MMSN811: Aztech Sound Galaxy Nova 16 Extra
FCC-ID I38-MMSN822: Aztech Sound Galaxy Pro 16 II

and for snd-azt2316:

FCC-ID I38-MMSN824: Aztech Sound Galaxy Pro 16 AB
FCC-ID I38-MMSN826: Trust Sound Expert DeLuxe Wave 32 (05201)
FCC-ID I38-MMSN830: Trust Sound Expert DeLuxe 16+ (05202)
FCC-ID I38-MMSN837: Packard Bell ISA Soundcard 030069
FCC-ID I38-MMSN846: Trust Sound Expert DeLuxe 16-3D (06300)
FCC-ID I38-MMSN847: Trust Sound Expert DeLuxe Wave 32-3D (06301)
FCC-ID I38-MMSN852: Aztech Sound Galaxy Waverider Pro 32-3D

826 and 846 were also marketed directly by Aztech and then known as:

FCC-ID I38-MMSN826: Aztech Sound Galaxy Waverider 32+
FCC-ID I38-MMSN846: Aztech Sound Galaxy Nova 16 Extra II-3D

Together, these cover the AZT1605 and AT2316A, AZT2316R and AZT2316-S
chipsets. All cards work fully -- full-duplex PCM, MIDI and FM. Full
duplex is a little flaky on some.

I38-MSN811 tends to not work in full-duplex but sometimes does with the
highest success rate being achieved when you first start the capture and
then a playback instead of the other way around (it's a CS4231-KL
codec).

The cards with an AD1845XP codec (my I38-MMSN826 and one of my
I38-MMSN830s) are also somewhat duplex-challenged. Sometimes full-duplex
works, sometimes not and this varies from try to try. This seems likely
to be a timing problem somewhere inside wss-lib.

I38-MMSN826 has an additional "ICS2115 WaveFront" wavetable synth
onboard that isn't supported yet. The wavetable synths on I38-MMSN847
and I38-MMSN852 are wired directly to the standard MPU-401 UART and the
AUX1 input on the codec and work without problem.

CD-ROM audio on the cards is routed to the codec "Line" input, Line-In
to its Aux input, and FM/Wavetable to its AUX1 input. I did not rename
the controls due to the capture source enumeration: I see that
capture-source overrides are hardcoded in wss-lib and this is just too
ugly to live.

Versus the old snd-sgalaxy driver these drivers add support for the
models without a configuration EEPROM (which are common), full-duplex,
MPU-401 UART and OPL3. In the future they might grow support for that
ICS2115 WaveFront synth on 826 and an hwdep interface to write to the
EEPROM on the models that have one.
Signed-off-by: NRene Herman <rene.herman@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (59 commits)
  igbvf.txt: Add igbvf Documentation
  igb.txt: Add igb documentation
  e100/e1000*/igb*/ixgb*: Add missing read memory barrier
  ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
  netxen: protect tx timeout recovery by rtnl lock
  isdn: gigaset: use after free
  isdn: gigaset: add missing unlock
  solos-pci: Fix race condition in tasklet RX handling
  pkt_sched: Fix sch_sfq vs tcf_bind_filter oops
  net: disable preemption before call smp_processor_id()
  tcp: no md5sig option size check bug
  iwlwifi: fix locking assertions
  iwlwifi: fix TX tracer
  isdn: fix information leak
  net: Fix napi_gro_frags vs netpoll path
  usbnet: remove noisy and hardly useful printk
  rtl8180: avoid potential NULL deref in rtl8180_beacon_work
  ath9k: Remove myself from the MAINTAINERS list
  libertas: scan before assocation if no BSSID was given
  libertas: fix association with some APs by using extended rates
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
  tx493xide: use min_t() macro instead of min()
  drivers/ide: Use memdup_user
  via82cxxx: fix typo for VT6415 PCIE PATA IDE Host Controller support.
  ide-cd: Do not access completed requests in the irq handler

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Update defconfig.
  sparc: Kill user copy check code.
  sparc64: Fix perf_arch_get_caller_regs().
  sparc64: Add missing ID to parport probing code.

* 'rs485fix' of git://www.jni.nu/cris:
  CRIS: ioctl for getting RS485 information

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: fix build with make 3.82
  Revert "Input: appletouch - fix integer overflow issue"
  memblock: Fix memblock_is_region_reserved() to return a boolean
  powerpc: Trim defconfigs
  powerpc: fix i8042 module build error
  sound/soc: mpc5200_psc_ac97: Use gpio pins for cold reset
  powerpc/5200: add mpc5200_psc_ac97_gpio_reset

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (32 commits)
  Blackfin: gpio: add a debounce stub
  Blackfin: update defconfigs
  Blackfin: remove CONFIG_MEM_GENERIC_BOARD
  Blackfin: dpmc: punt unnecessary RTC_ISTAT clearing
  Blackfin: unify rotary encoder bitmasks
  Blackfin: unify SDH/RSI bitmasks
  Blackfin: BF54x: tweak DMAC MMR naming to match other ports
  Blackfin: TWI: clean up the MMR names
  Blackfin: add EVT_OVERRIDE/IPRIO core MMR helpers
  Blackfin: add support for dynamic ftrace
  Blackfin: add support for LZO compressed kernels
  Blackfin: portmux: fix peripheral map overflow when requesting pins
  Blackfin: document SPI CS limitations with CPHA=0
  Blackfin: remove useless and outdated documentation
  Blackfin: BF51x/BF52x: support GPIO Hysteresis/Schmitt Trigger options
  Blackfin: gpio/portmux: clean up whitespace corruption
  Blackfin: make sure mmiowb inserts a write barrier with SSYNC
  Blackfin: fix DMA/cache bug when resuming from suspend to RAM
  Blackfin: BF51x: fix handling of PH8 (the "internal" SPI0SEL4 pin)
  Blackfin: add a GPIO_DEFAULT_BOOT_SPI_CS
  ...

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (30 commits)
  DMAENGINE: at_hdmac: locking fixlet
  DMAENGINE: pch_dma: kill another usage of __raw_{read|write}l
  dma: dmatest: fix potential sign bug
  ioat2: catch and recover from broken vtd configurations v6
  DMAENGINE: add runtime slave control to COH 901 318 v3
  DMAENGINE: add runtime slave config to DMA40 v3
  DMAENGINE: generic slave channel control v3
  dmaengine: Driver for Topcliff PCH DMA controller
  intel_mid: Add Mrst & Mfld DMA Drivers
  drivers/dma: Eliminate a NULL pointer dereference
  dma/timb_dma: compile warning on 32 bit
  DMAENGINE: ste_dma40: support older silicon
  DMAENGINE: ste_dma40: support disabling physical channels
  DMAENGINE: ste_dma40: no disabled phy channels on ux500
  DMAENGINE: ste_dma40: fix suspend bug
  DMAENGINE: ste_dma40: add DB8500 memcpy channels
  DMAENGINE: ste_dma40: no flow control on memcpy
  DMAENGINE: ste_dma40: arch updates for LCLA and LCPA
  DMAENGINE: ste_dma40: allocate LCLA dynamically
  DMAENGINE: ste_dma40: no premature stop
  ...

Fix up trivial conflicts in arch/arm/mach-ux500/devices-db8500.c

According include/linux/console_struct.h,vc_scr_end is unsigned long.

struct vc_data {
    unsigned short  vc_num;         /* Console number */
    unsigned int    vc_cols;        /* [#] Console size */
    unsigned int    vc_rows;
    unsigned int    vc_size_row;        /* Bytes per row */
    unsigned int    vc_scan_lines;      /* # of scan lines */
    unsigned long   vc_origin;      /* [!] Start of real screen */
    unsigned long   vc_scr_end;     /* [!] End of real screen */
    unsigned long   vc_visible_origin;  /* [!] Top of visible window */
    unsigned int    vc_top, vc_bottom;  /* Scrolling region */
    const struct consw *vc_sw;
    unsigned short  *vc_screenbuf;
...
}
Signed-off-by: Nqiaochong <qiaochong@loongson.cn>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kernel will die on some platform when switch from vga mode to framebuffer
mode.  The reason of this bug is that bind_con_driver reset vc->vc_origin
to (unsigned long)vc->vc_screenbuf.

On vgacon vc->vc_origin is not releated to vc->vc_screenbuf,if set
vc->vc_origin to vc->vc_screenbuf,kernel will die on vc_do_resize.

static int vc_do_resize(struct tty_struct *tty, struct tty_struct *real_tty,
        struct vc_data *vc, unsigned int cols, unsigned int lines)
{
    unsigned long old_origin, new_origin, new_scr_end, rlth, rrem, err = 0;
    unsigned int old_cols, old_rows, old_row_size, old_screen_size;
    unsigned int new_cols, new_rows, new_row_size, new_screen_size;
    unsigned int end, user;
...
        end = (old_rows > new_rows) ? old_origin +
            (old_row_size * new_rows) :
            vc->vc_scr_end;

...
/*
here for a test from vgacon to framebuffer:
old_origin=0x810814a0,end=0xb00b8fa0,vc->vc_origin=0x810814a0
the code bellow will copy memory from 0x810814a0 to 0xb00b8fa0,
this will cover kernel code,kernel died here.
*/

    while (old_origin < end) {

        scr_memcpyw((unsigned short *) new_origin,
                (unsigned short *) old_origin, rlth);
        if (rrem)
            scr_memsetw((void *)(new_origin + rlth),
                    vc->vc_video_erase_char, rrem);
        old_origin += old_row_size;
        new_origin += new_row_size;
    }

...
}

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Nqiaochong <qiaochong@loongson.cn>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

More code can be pushed from rwsem_down_read_failed and
rwsem_down_write_failed into rwsem_down_failed_common.

Following change adding down_read_critical infrastructure support also
enjoys having flags available in a register rather than having to fish it
out in the struct rwsem_waiter...
Signed-off-by: NMichel Lespinasse <walken@google.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This change addresses the following situation:

- Thread A acquires the rwsem for read
- Thread B tries to acquire the rwsem for write, notices there is already
  an active owner for the rwsem.
- Thread C tries to acquire the rwsem for read, notices that thread B already
  tried to acquire it.
- Thread C grabs the spinlock and queues itself on the wait queue.
- Thread B grabs the spinlock and queues itself behind C. At this point A is
  the only remaining active owner on the rwsem.

In this situation thread B could notice that it was the last active writer
on the rwsem, and decide to wake C to let it proceed in parallel with A
since they both only want the rwsem for read.
Signed-off-by: NMichel Lespinasse <walken@google.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previously each waiting thread added a bias of RWSEM_WAITING_BIAS.  With
this change, the bias is added only once to indicate that the wait list is
non-empty.

This has a few nice properties which will be used in following changes:
- when the spinlock is held and the waiter list is known to be non-empty,
  count < RWSEM_WAITING_BIAS  <=>  there is an active writer on that sem
- count == RWSEM_WAITING_BIAS  <=>  there are waiting threads and no
                                     active readers/writers on that sem
Signed-off-by: NMichel Lespinasse <walken@google.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In __rwsem_do_wake(), we can skip the active count check unless we come
there from up_xxxx().  Also when checking the active count, it is not
actually necessary to increment it; this allows us to get rid of the read
side undo code and simplify the calculation of the final rwsem count
adjustment once we've counted the reader threads to wake.

The basic observation is the following.  When there are waiter threads on
a rwsem and the spinlock is held, other threads can only increment the
active count by trying to grab the rwsem in down_xxxx().  However
down_xxxx() will notice there are waiter threads and take the down_failed
path, blocking to acquire the spinlock on the way there.  Therefore, a
thread observing an active count of zero with waiters queued and the
spinlock held, is protected against other threads acquiring the rwsem
until it wakes the last waiter or releases the spinlock.
Signed-off-by: NMichel Lespinasse <walken@google.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is in preparation for later changes in the series.

In __rwsem_do_wake(), the first queued waiter is checked first in order to
determine whether it's a writer or a reader.  The code paths diverge at
this point.  The code that checks and increments the rwsem active count is
duplicated on both sides - the point is that later changes in the series
will be able to independently modify both sides.
Signed-off-by: NMichel Lespinasse <walken@google.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow device probing to recognise the Fintek F71808E.

Sysfs interface:
 * Fan/pwm control is the same as for F71889FG
 * Temperature and voltage sensor handling is largely the same as for
   the F71889FG
  - Has one temperature sensor less (doesn't have temp3)
  - Misses one voltage sensor (doesn't have V6, thus in6_input refers to
    what in7_input refers for F71889FG)

For the purpose of the sysfs interface fxxxx_in_temp_attr[] is split up
such that it can largely be reused.
Signed-off-by: NGiel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

register_hotcpu_notifier() is designed to make these ifdefs unnecessary.

Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update coretemp supported CPU TjMax lists and some cleanup work.
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If one coretemp device can't be added, it should allow subsequent adding
operation because every new-added device will create a new sysfs group,
not an additional sensor sys entry.
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix two errors in hotplug.  One is for hotplug notifier.  The other is
unnecessary driver unregister.  Because even none of online cpus supports
coretemp, we can't assume new onlined cpu doesn't support it either.  If
related driver is unregistered there we have no chance to use coretemp
from then on.
Signed-off-by: NChen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver adds support for the monitoring features of the Summit
Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver will report the heading values in degrees to the sysfs
interface.  The values returned are headings .  e.g.  245.6

Alan: Cleanups requested now all folded in and a sysfs description to keep
Andrew happy. The sysfs description now resembles hwmon.
Signed-off-by: NKalhan Trisal <kalhan.trisal@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add Lenovo Thinkpad T400.  I have done the testing on my laptop.  The
hdaps module detects the device and the hdapsd daemon is able to [un]park
the disk.
Signed-off-by: NRitesh Raj Sarraf <rrs@debian.org>
Cc: Frank Seidel <frank@f-seidel.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These are caused by checkpatch incorrectly parsing its internal
representation of a statement block for struct's (or anything else that is
a statement block encapsulated in {}'s that also ends with a ';').  Fix
this by properly parsing a statement block.

An example:

	+struct dummy_type dummy = {
	+	.foo	= "baz",
	+};
	+EXPORT_SYMBOL_GPL(dummy);
	+
	+static int dummy_func(void)
	+{
	+	return -EDUMMYCODE;
	+}
	+EXPORT_SYMBOL_GPL(dummy_func);

	WARNING: EXPORT_SYMBOL(foo); should immediately \
		follow its function/variable
	#19: FILE: dummy.c:4:
	+EXPORT_SYMBOL_GPL(dummy);

The above warning is issued when it should not be.
Signed-off-by: NPatrick Pannuto <ppannuto@codeaurora.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As explained in Documentation/timers/timers-howto.txt, msleep's of < 20ms
may sleep for as long as 20ms.  Caller's of msleep(1) or msleep(2), etc
are likely not to expect this quirky behavior - warn them.
Signed-off-by: NPatrick Pannuto <ppannuto@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When possible, sleeping is (usually) better than delaying; however, don't
bother callers of udelay < 10us, as those cases are generally not worth
the switch to usleep

[akpm@linux-foundation.org: fix mismatched parentheses]
Signed-off-by: NPatrick Pannuto <ppannuto@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add new logging functions netdev_<level> and netif_<level>.
Don't complain if the only thing on a line is a quoted string.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make error message say 'ERROR: do not initialise globals to 0 or NULL'
rather than 'ERROR: do not initialise externals to 0 or NULL'.  Makes more
sense in the context since there is an extern keyword in C and that is a
global declaration within the scope of the current file.
Signed-off-by: NJoe Eloff <kagen101@gmail.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I've got a false positive when spaces are present at the beginning of a
line.

So I add this check, obviously excluding to check the lines in the middle of
comments.

For instance this code passes the checkpatch test:

+struct davinci_mcbsp_data {
+       unsigned int    fmt;
+    int             clk_div;
+};
+
+static struct davinci_mcbsp_data mcbsp_data;

Where, before the string "int             clk_div", I have 4 spaces (\040
ascii character).

With v2.6.34 scripts/checkpatch.pl script I get:

scripts/checkpatch.pl 0001-ASoC-DaVinci-Added-support-for-stereo-I2S.patch
total: 0 errors, 0 warnings, 201 lines checked
0001-ASoC-DaVinci-Added-support-for-stereo-I2S.patch has no obvious style
problems and is ready for submission.

That is not correct.  Instead with the proposed patch I get:

scripts/checkpatch.pl 0001-ASoC-DaVinci-Added-support-for-stereo-I2S.patch
WARNING: please, no space for starting a line,
                excluding comments
#63: FILE: sound/soc/davinci/davinci-i2s.c:165:
+    int             clk_div;$

WARNING: please, no space for starting a line,
                excluding comments
#95: FILE: sound/soc/davinci/davinci-i2s.c:406:
+    return 0;$

total: 0 errors, 2 warnings, 201 lines checked

That is correct.
Signed-off-by: NRaffaele Recalcati <raffaele.recalcati@bticino.it>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change the check suggesting replacement of asm-includes with
linux-includes.  Exceptions to this rule are easier to extend now.  Add
memory.h because ARM has a custom one.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The error may happen at any iteration of the for loop, this patch properly
unregisters already registed edd_devices in error path.

[akpm@linux-foundation.org: remove unneeded NULL test]
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Getting and putting arrays of pointers with flex arrays is a PITA.  You
have to remember to pass &ptr to the _put and you have to do weird and
wacky casting to get the ptr back from the _get.  Add two functions
flex_array_get_ptr() and flex_array_put_ptr() to handle all of the magic.

[akpm@linux-foundation.org: simplification suggested by Joe]
Signed-off-by: NEric Paris <eparis@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: James Morris <jmorris@namei.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The strict_strtoul() and strict_strtoull() functions used strlen() to
check argument's length in a situation where it wasn't strictly necessary
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Cc: "Yi Yang" <yi.y.yang@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the magic LIST_POISON* values to detect an incorrect use of list_del
on a deleted entry.  This DEBUG_LIST specific warning is easier to
understand than the generic Oops message caused by LIST_POISON
dereference.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This old address bounces and Sergey doesn't answer at another email
address.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Sergey Kostyliov <rathamahata@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Laurent is sending auto-replies with a new email address, so might as well
update MAINTAINERS.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NSubrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NInaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Jim Paris <jim@jtan.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>