Fix a bunch of spelling errors in the rt2x00 drivers
Signed-off-by: NLuis Correia <luis.f.correia@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use %pM instead, and also remove stray variables
declared with DECLARE_MAC_BUF.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The DEVICE_STATE_DISABLED_RADIO_HW flag is only read but never set,
it is an ancient part of one of the many versions of the rfkill implementations
in rt2x00. It is about time is disappears.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement set_tim callback for all rt2x00 drivers, this makes the
device wake up powersaving stations properly while in AP mode.

The only way to update the beacon is by simply calling mac80211 and
requesting the new beacon. This means the set_tim() event is mostly the
same as a beacon_done() event which was already defined in rt2x00lib.
Signed-off-by: NStefan Steuerwald <salsasepp@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit below changed the semantics of rt2x00_check_rev so that it no
longer checked the bottom 4 bits of the rev were non-zero.  During that
conversion this part of the check was not propogated to the rt2500usb
initialisation.

    commit 358623c2
    Author: Ivo van Doorn <ivdoorn@gmail.com>
    Date:   Tue May 5 19:46:08 2009 +0200

        rt2x00: Simplify rt2x00_check_rev

Without this check rt73 devices are miss recognised as rt2500 devices and
two drivers are loaded.  Preventing the device being used.  Reinstate this
check.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the input_polldev from rt2x00 and replace it with
the rfkill interface offered by the wiphy structure. This
simplifies the entire rfkill handling in rt2x00 and allows
us to remove the CONFIG_RT2X00_LIB_RFKILL option and always
enables rfkill capabilities.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johannes is trying to get rid of the master netdev and in the process will
remove skb->do_not_encrypt field. This removes the do_not_encrypt
usage from rt2x00 to make the change easier.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

trivial: fix typos s/paramter/parameter/ and s/excute/execute/ in documentation and source comments.
Signed-off-by: NMartin Olsson <martin@minimum.se>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This removes the last usage of beacon_int inside the iee80211_config
structure from rt2x00. The attempt is a bit hackish, and subject to
change in the future when the entire rt2x00_dev structure is
cleaned up and restructured.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

new patch to add more usb_dev to rt2800usb.c .
IDs 'stolen' from the latest Ralink linux
driver(2009_0520_RT3070_Linux_STA_v2.1.1.0.tar.gz)
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago,
it is about time to remove all usage from the rt2x00 drivers and
use the correct beacon interval configuration through the bss_info
structure.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The USB ID with unknown manufacturer is apparently sweex,
copy it to the correct location of the list and add 2
additional USB ID's also belonging to Sweex.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report status unknown as if there were successfully transmitted.
This will avoid hostapd to disassociate because it doesn't understand what a status unknown is.
Signed-off-by: NAlexandre Becholey <alexandre.becholey@epfl.ch>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not go beyond ARRAY_SIZE of intf->crypto_stats
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The lower 4 bytes of the chipset revision must contain
a non-zero value. This bug was introduced by
"rt2x00: Simplify rt2x00_check_rev".
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00_check_rev() was too specific for rt2500usb and rt73usb,
by adding the mask argument (instead of hardcoding it into
the function itself) we can use the function in rt2800usb as
well.

v2: Fix revision mask for rt2800usb
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ralink released a new rt2870 driver, these are the obvious
differences I could find. It doesn't same to make my device
work better, but neither does it seem to regress...
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for the rt2800usb chipset.

Current problems:
 * Cannot scan 11n AP's
 * No TX during first minute after association
 * Broken Hardware encryption

Includes various patches from Mattias, Felix, Xose and Axel.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NAxel Kollhofer <rain_maker@root-forum.org>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extra parenthesis are not needed in these 2 cases,
all other defines in rt2x00 are done without parenthesis
so just fixup these 2 cases.
Signed-off-by: NAlban Browaeys <prahal@yahoo.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By placing the iv_len into the tx descriptor data and
by passing this data to the crypto IV handlers we can
save multiple calls to ieee80211_get_hdrlen_from_skb()
and some if-statements when copying/removing the IV data
from the outgoing frame.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00link_reset_qual() is not declared in a header,
and is only internally used within rt2x00link.c.
It should be declared as static.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

pci_dev->irq and pci_name(pci_dev) access should be limited
to rt2x00pci only. This is more generic and allows a rt2x00 pci
driver to be controlled as PCI device but also as platform driver
(needed for rt2800pci SoC support).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After suspend & resume the rt2x00 devices won't wakeup
anymore due to a broken register information setup.
The most important problem is the release of the EEPROM
buffer which is completely cleared and never read again
after the suspend.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In a scenario where there isn't any firmware available, we will have a
double kfree of rt2x00dev->spec.channels_info when ieee80211_register_hw
returns an error status inside rt2x00lib_probe_hw.

The problem is that if ieee80211_register_hw fails, we call
rt2x00lib_remove_hw twice:
* first inside rt2x00lib_probe_hw upon failure of ieee80211_register_hw
* error status is returned to rt2x00lib_probe_dev, which then sees it and
  calls in this case rt2x00lib_remove_dev that will again run
  rt2x00lib_remove_hw

Prevent this avoiding calling rt2x00lib_remove_hw inside
rt2x00lib_probe_hw

Problem was detected with CONFIG_DEBUG_PAGEALLOC=y, CONFIG_SLUB_DEBUG=y,
CONFIG_SLUB_DEBUG_ON=y, that dumps this with no firmware available:

rt61pci 0000:00:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
wmaster0 (rt61pci): not using net_device_ops yet
phy0: Selected rate control algorithm 'pid'
phy0: Failed to initialize wep: -2
phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw.
=============================================================================
BUG kmalloc-128: Object already free
-----------------------------------------------------------------------------

INFO: Allocated in rt61pci_probe_hw+0x3e5/0x6e0 [rt61pci] age=340 cpu=0 pid=21
INFO: Freed in rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib] age=0 cpu=0 pid=21
INFO: Slab 0xc13ac3e0 objects=23 used=10 fp=0xdd59f6e0 flags=0x400000c3
INFO: Object 0xdd59f6e0 @offset=1760 fp=0xdd59f790

Bytes b4 0xdd59f6d0:  15 00 00 00 b2 8a fb ff 5a 5a 5a 5a 5a 5a 5a 5a ....².ûÿZZZZZZZZ
  Object 0xdd59f6e0:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f6f0:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f700:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f710:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f720:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f730:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f740:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f750:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk¥
 Redzone 0xdd59f760:  bb bb bb bb                                     »»»»
 Padding 0xdd59f788:  5a 5a 5a 5a 5a 5a 5a 5a                         ZZZZZZZZ
Pid: 21, comm: stage1 Not tainted 2.6.29.1-desktop-1.1mnb #1
Call Trace:
 [<c01abbb3>] print_trailer+0xd3/0x120
 [<c01abd37>] object_err+0x37/0x50
 [<c01acf57>] __slab_free+0xe7/0x2f0
 [<c01ad1de>] kfree+0x7e/0xd0
 [<e0e4a239>] ? rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4a239>] ? rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4a239>] rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4acc7>] rt2x00lib_remove_dev+0x37/0x50 [rt2x00lib]
 [<e0e4b087>] rt2x00lib_probe_dev+0x1a7/0x3b0 [rt2x00lib]
 [<e0eb288f>] rt2x00pci_probe+0xdf/0x1ee [rt2x00pci]
 [<c026b9ee>] local_pci_probe+0xe/0x10
 [<c026c750>] pci_device_probe+0x60/0x80
 [<c02d5c2a>] driver_probe_device+0x9a/0x2e0
 [<c02d5ef9>] __driver_attach+0x89/0x90
 [<c02d541b>] bus_for_each_dev+0x4b/0x70
 [<c026c690>] ? pci_device_remove+0x0/0x40
 [<c02d59d9>] driver_attach+0x19/0x20
 [<c02d5e70>] ? __driver_attach+0x0/0x90
 [<c02d4cef>] bus_add_driver+0x1cf/0x2a0
 [<c026c690>] ? pci_device_remove+0x0/0x40
 [<c02d60c9>] driver_register+0x69/0x140
 [<c026c9b0>] __pci_register_driver+0x40/0x80
 [<e0ecc000>] ? rt61pci_init+0x0/0x19 [rt61pci]
 [<e0ecc017>] rt61pci_init+0x17/0x19 [rt61pci]
 [<c0101116>] do_one_initcall+0x26/0x1c0
 [<c01ab90c>] ? slab_pad_check+0x3c/0x120
 [<c01ab90c>] ? slab_pad_check+0x3c/0x120
 [<c01ac8da>] ? check_object+0xda/0x210
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01ad09e>] ? __slab_free+0x22e/0x2f0
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01687ec>] ? stop_machine_destroy+0x3c/0x40
 [<c015e515>] ? load_module+0xa5/0x1c50
 [<e0ec5000>] ? rt61pci_eepromregister_read+0x0/0x40 [rt61pci]
 [<e0eb2000>] ? rt2x00pci_write_tx_data+0x0/0x90 [rt2x00pci]
 [<c03ac2fb>] ? mutex_lock+0xb/0x20
 [<c03ac2fb>] ? mutex_lock+0xb/0x20
 [<c017ad16>] ? tracepoint_update_probe_range+0x76/0xa0
 [<c017ad6f>] ? tracepoint_module_notify+0x2f/0x40
 [<c03b02ed>] ? notifier_call_chain+0x2d/0x70
 [<c014f0ed>] ? __blocking_notifier_call_chain+0x4d/0x60
 [<c014f11a>] ? blocking_notifier_call_chain+0x1a/0x20
 [<c0160156>] sys_init_module+0x96/0x1d0
 [<c019dad6>] ? sys_munmap+0x46/0x60
 [<c0105546>] syscall_call+0x7/0xb
FIX kmalloc-128: Object at 0xdd59f6e0 not freed
rt61pci 0000:00:07.0: PCI INT A disabled
rt61pci: probe of 0000:00:07.0 failed with error -2
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By exporting the register base, and word size to userspace
through debugfs it will be easier to create scripts which
parse the register information. This makes debugging and
register dumps information easier.

This will break my previous scripts which dumped and parsed
all information, but since this is only for debugging purposes
this change should not be a problem.

Dumpfiles created with the old version can be easily manually
edited to make them compatible with this new approach, which
means there will be no problems comparing dumps from the
different versions either.

Also be more consistent with using tabs to seperate different
fields.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Software antenna tuning is broken because of an function
ordering problem during rt2x00link_tuner().

rt2x00link_precalculate_signal()
rt2x00leds_led_quality()
rt2x00lib_antenna_diversity()

rt2x00link_precalculate_signal() will reset the quality TX/RX counters,
however rt2x00lib_antenna_diversity() requires the RX counter to
see what RSSI value must be used for a particular antenna.
We can't change the ordering since rt2x00lib_antenna_diversity() might
reset other statistics which are needed by the function called earlier.

Move the reset of the quality TX/RX counters into a seperate function
and move the call to after rt2x00lib_antenna_diversity().
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

add more usb_dev to rt73usb.c . IDs 'stolen' from the
windows inf file(10/21/2008, 1.03.02.0000) plus some
from the Ralink linux driver(2009_0206_RT73_Linux_STA_Drv1.1.0.2.tar.bz2)
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

add more usb_dev to rt2500usb.c . IDs 'stolen' from the
windows inf file(02/12/2009, 2.01.01.0015).
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The word_base is in bytes instead of word index number,
this means that when using it, it should be transformed into
a word index first.

Otherwise RF register reading will fail through debugfs since
we would start reading 4 words starting with word 4 (which is the last
valid word for RF).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>