Impact: extend and enable the function graph tracer to 64-bit x86

This patch implements the support for function graph tracer under x86-64.
Both static and dynamic tracing are supported.

This causes some small CPP conditional asm on arch/x86/kernel/ftrace.c I
wanted to use probe_kernel_read/write to make the return address
saving/patching code more generic but it causes tracing recursion.

That would be perhaps useful to implement a notrace version of these
function for other archs ports.

Note that arch/x86/process_64.c is not traced, as in X86-32. I first
thought __switch_to() was responsible of crashes during tracing because I
believed current task were changed inside but that's actually not the
case (actually yes, but not the "current" pointer).

So I will have to investigate to find the functions that harm here, to
enable tracing of the other functions inside (but there is no issue at
this time, while process_64.c stays out of -pg flags).

A little possible race condition is fixed inside this patch too. When the
tracer allocate a return stack dynamically, the current depth is not
initialized before but after. An interrupt could occur at this time and,
after seeing that the return stack is allocated, the tracer could try to
trace it with a random uninitialized depth. It's a prevention, even if I
hadn't problems with it.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: make ftrace position computing more sane

First remove useless ->pos field. Then we needn't check seq_printf
in .show like other place.
Signed-off-by: NLiming Wang <liming.wang@windriver.com>
Reviewed-by: NBruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: feature

This patch enables function tracing and function return to run together.
I've tested this by enabling the stack tracer and return tracer, where
both the function entry and function return are used together with
dynamic ftrace.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: more efficient code for ftrace graph tracer

This patch uses the dynamic patching, when available, to patch
the function graph code into the kernel.

This patch will ease the way for letting both function tracing
and function graph tracing run together.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: feature to function trace a single thread

This patch adds the ability to function trace a single thread.
The file:

  /debugfs/tracing/set_ftrace_pid

contains the pid to trace. Valid pids are any positive integer.
Writing any negative number to this file will disable the pid
tracing and the function tracer will go back to tracing all of
threads.

This feature works with both static and dynamic function tracing.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: feature

This patch sets a C-like output for the function graph tracing.
For this aim, we now call two handler for each function: one on the entry
and one other on return. This way we can draw a well-ordered call stack.

The pid of the previous trace is loosely stored to be compared against
the one of the current trace to see if there were a context switch.

Without this little feature, the call tree would seem broken at
some locations.
We could use the sched_tracer to capture these sched_events but this
way of processing is much more simpler.

2 spaces have been chosen for indentation to fit the screen while deep
calls. The time of execution in nanosecs is printed just after closed
braces, it seems more easy this way to find the corresponding function.
If the time was printed as a first column, it would be not so easy to
find the corresponding function if it is called on a deep depth.

I plan to output the return value but on 32 bits CPU, the return value
can be 32 or 64, and its difficult to guess on which case we are.
I don't know what would be the better solution on X86-32: only print
eax (low-part) or even edx (high-part).

Actually it's thee same problem when a function return a 8 bits value, the
high part of eax could contain junk values...

Here is an example of trace:

sys_read() {
  fget_light() {
  } 526
  vfs_read() {
    rw_verify_area() {
      security_file_permission() {
        cap_file_permission() {
        } 519
      } 1564
    } 2640
    do_sync_read() {
      pipe_read() {
        __might_sleep() {
        } 511
        pipe_wait() {
          prepare_to_wait() {
          } 760
          deactivate_task() {
            dequeue_task() {
              dequeue_task_fair() {
                dequeue_entity() {
                  update_curr() {
                    update_min_vruntime() {
                    } 504
                  } 1587
                  clear_buddies() {
                  } 512
                  add_cfs_task_weight() {
                  } 519
                  update_min_vruntime() {
                  } 511
                } 5602
                dequeue_entity() {
                  update_curr() {
                    update_min_vruntime() {
                    } 496
                  } 1631
                  clear_buddies() {
                  } 496
                  update_min_vruntime() {
                  } 527
                } 4580
                hrtick_update() {
                  hrtick_start_fair() {
                  } 488
                } 1489
              } 13700
            } 14949
          } 16016
          msecs_to_jiffies() {
          } 496
          put_prev_task_fair() {
          } 504
          pick_next_task_fair() {
          } 489
          pick_next_task_rt() {
          } 496
          pick_next_task_fair() {
          } 489
          pick_next_task_idle() {
          } 489

------------8<---------- thread 4 ------------8<----------

finish_task_switch() {
} 1203
do_softirq() {
  __do_softirq() {
    __local_bh_disable() {
    } 669
    rcu_process_callbacks() {
      __rcu_process_callbacks() {
        cpu_quiet() {
          rcu_start_batch() {
          } 503
        } 1647
      } 3128
      __rcu_process_callbacks() {
      } 542
    } 5362
    _local_bh_enable() {
    } 587
  } 8880
} 9986
kthread_should_stop() {
} 669
deactivate_task() {
  dequeue_task() {
    dequeue_task_fair() {
      dequeue_entity() {
        update_curr() {
          calc_delta_mine() {
          } 511
          update_min_vruntime() {
          } 511
        } 2813
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: cleanup

This patch changes the name of the "return function tracer" into
function-graph-tracer which is a more suitable name for a tracing
which makes one able to retrieve the ordered call stack during
the code flow.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: fix a crash

While I killed the cat process, I got sometimes the following (but rare)
crash:

[   65.689027] Pid: 2969, comm: cat Not tainted (2.6.28-rc6-tip #83) AMILO Li 2727
[   65.689027] EIP: 0060:[<00000000>] EFLAGS: 00010082 CPU: 1
[   65.689027] EIP is at 0x0
[   65.689027] EAX: 00000000 EBX: f66cd780 ECX: c019a64a EDX: f66cd780
[   65.689027] ESI: 00000286 EDI: f66cd780 EBP: f630be2c ESP: f630be24
[   65.689027]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[   65.689027] Process cat (pid: 2969, ti=f630a000 task=f66cd780 task.ti=f630a000)
[   65.689027] Stack:
[   65.689027]  00000012 f630bd54 f630be7c c012c853 00000000 c0133cc9 f66cda54 f630be5c
[   65.689027]  f630be68 f66cda54 f66cd88c f66cd878 f7070000 00000001 f630be90 c0135dbc
[   65.689027]  f614a614 f630be68 f630be68 f65ba200 00000002 f630bf10 f630be90 c012cad6
[   65.689027] Call Trace:
[   65.689027]  [<c012c853>] ? do_exit+0x603/0x850
[   65.689027]  [<c0133cc9>] ? next_signal+0x9/0x40
[   65.689027]  [<c0135dbc>] ? dequeue_signal+0x8c/0x180
[   65.689027]  [<c012cad6>] ? do_group_exit+0x36/0x90
[   65.689027]  [<c013709c>] ? get_signal_to_deliver+0x20c/0x390
[   65.689027]  [<c0102b69>] ? do_notify_resume+0x99/0x8b0
[   65.689027]  [<c02e6d1a>] ? tty_ldisc_deref+0x5a/0x80
[   65.689027]  [<c014db9b>] ? trace_hardirqs_on+0xb/0x10
[   65.689027]  [<c02e6d1a>] ? tty_ldisc_deref+0x5a/0x80
[   65.689027]  [<c02e39b0>] ? n_tty_write+0x0/0x340
[   65.689027]  [<c02e1812>] ? redirected_tty_write+0x82/0x90
[   65.689027]  [<c019ee99>] ? vfs_write+0x99/0xd0
[   65.689027]  [<c02e1790>] ? redirected_tty_write+0x0/0x90
[   65.689027]  [<c019f342>] ? sys_write+0x42/0x70
[   65.689027]  [<c01035ca>] ? work_notifysig+0x13/0x19
[   65.689027] Code:  Bad EIP value.
[   65.689027] EIP: [<00000000>] 0x0 SS:ESP 0068:f630be24

This is because on do_exit(), kfree is called to free the return addresses stack
but kfree is traced and stored its return address in this stack.
This patch fixes it.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: use deeper function tracing depth safely

Some tests showed that function return tracing needed a more deeper depth
of function calls. But it could be unsafe to store these return addresses
to the stack.

So these arrays will now be allocated dynamically into task_struct of current
only when the tracer is activated.

Typical scheme when tracer is activated:
- allocate a return stack for each task in global list.
- fork: allocate the return stack for the newly created task
- exit: free return stack of current
- idle init: same as fork

I chose a default depth of 50. I don't have overruns anymore.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: clean up and fix for dyn ftrace filter selection

The previous logic of the dynamic ftrace selection of enabling
or disabling functions was complex and incorrect. This patch simplifies
the code and corrects the usage. This simplification also makes the
code more robust.

Here is the correct logic:

  Given a function that can be traced by dynamic ftrace:

  If the function is not to be traced, disable it if it was enabled.
  (this is if the function is in the set_ftrace_notrace file)

  (filter is on if there exists any functions in set_ftrace_filter file)

  If the filter is on, and we are enabling functions:
    If the function is in set_ftrace_filter, enable it if it is not
      already enabled.
    If the function is not in set_ftrace_filter, disable it if it is not
      already disabled.

  Otherwise, if the filter is off and we are enabling function tracing:
    Enable the function if it is not already enabled.

  Otherwise, if we are disabling function tracing:
    Disable the function if it is not already disabled.

This code now sets or clears the ENABLED flag in the record, and at the
end it will enable the function if the flag is set, or disable the function
if the flag is cleared.

The parameters for the function that does the above logic is also
simplified. Instead of passing in confusing "new" and "old" where
they might be swapped if the "enabled" flag is not set. The old logic
even had one of the above always NULL and had to be filled in. The new
logic simply passes in one parameter called "nop". A "call" is calculated
in the code, and at the end of the logic, when we know we need to either
disable or enable the function, we can then use the "nop" and "call"
properly.

This code is more robust than the previous version.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: fix filter selection to apply when set

It can be confusing when the set_filter_functions is set (or cleared)
and the functions being recorded by the dynamic tracer does not
match.

This patch causes the code to be updated if the function tracer is
enabled and the filter is changed.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: fix of output of set_ftrace_filter

The commit "ftrace: do not show freed records in
             available_filter_functions"

Removed a bit too much from the set_ftrace_filter code, where we now see
all functions in the set_ftrace_filter file even when we set a filter.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: make output of available_filter_functions complete

phenomenon:

The first value of dyn_ftrace_total_info is not equal with
`cat available_filter_functions | wc -l`, but they should be equal.

root cause:

When printing functions with seq_printf in t_show, if the read buffer
is just overflowed by current function record, then this function
won't be printed to user space through read buffer, it will
just be dropped. So we can't see this function printing.

So, every time the last function to fill the read buffer, if overflowed,
will be dropped.

This also applies to set_ftrace_filter if set_ftrace_filter has
more bytes than read buffer.

fix:

Through checking return value of seq_printf, if less than 0, we know
this function doesn't be printed. Then we decrease position to force
this function to be printed next time, in next read buffer.

Another little fix is to show correct allocating pages count.
Signed-off-by: Nwalimis <walimisdev@gmail.com>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch adds the support for dynamic tracing on the function return tracer.
The whole difference with normal dynamic function tracing is that we don't need
to hook on a particular callback. The only pro that we want is to nop or set
dynamically the calls to ftrace_caller (which is ftrace_return_caller here).

Some security checks ensure that we are not trying to launch dynamic tracing for
return tracing while normal function tracing is already running.

An example of trace with getnstimeofday set as a filter:

ktime_get_ts+0x22/0x50 -> getnstimeofday (2283 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1396 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1382 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1825 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1426 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1464 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1524 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1382 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1382 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1434 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1464 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1502 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1404 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1397 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1051 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1314 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1344 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1163 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1390 ns)
ktime_get_ts+0x22/0x50 -> getnstimeofday (1374 ns)
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: set filtered functions at time the filter is set

It can be confusing when the set_filter_functions is set (or cleared)
and the functions being recorded by the dynamic tracer does not
match.

This patch causes the code to be updated if the function tracer is
enabled and the filter is changed.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: correct implementation of dyn ftrace filter

The old decisions made by the filter algorithm was complex and incorrect.
This lead to inconsistent enabling or disabling of functions when
the filter was used.

This patch simplifies that code and in doing so, corrects the usage
of the filters.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: make ftrace_convert_nops() more permissive

Due to the way different architecture linkers combine the data sections
of the mcount_loc (the section that lists all the locations that
call mcount), there may be zeros added in that section. This is usually
due to strange alignments that the linker performs, that pads in zeros.

This patch makes the conversion code to nops skip any pointer in
the mcount_loc section that is NULL.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: allow archs more flexibility on dynamic ftrace implementations

Dynamic ftrace has largly been developed on x86. Since x86 does not
have the same limitations as other architectures, the ftrace interaction
between the generic code and the architecture specific code was not
flexible enough to handle some of the issues that other architectures
have.

Most notably, module trampolines. Due to the limited branch distance
that archs make in calling kernel core code from modules, the module
load code must create a trampoline to jump to what will make the
larger jump into core kernel code.

The problem arises when this happens to a call to mcount. Ftrace checks
all code before modifying it and makes sure the current code is what
it expects. Right now, there is not enough information to handle modifying
module trampolines.

This patch changes the API between generic dynamic ftrace code and
the arch dependent code. There is now two functions for modifying code:

  ftrace_make_nop(mod, rec, addr) - convert the code at rec->ip into
       a nop, where the original text is calling addr. (mod is the
       module struct if called by module init)

  ftrace_make_caller(rec, addr) - convert the code rec->ip that should
       be a nop into a caller to addr.

The record "rec" now has a new field called "arch" where the architecture
can add any special attributes to each call site record.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: keep from converting freed records

When the tracer is started or stopped, it converts all code pointed
to by the saved records into callers to ftrace or nops. When modules
are unloaded, their records are freed, but they still exist within
the record pages.

This patch changes the code to skip over freed records.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: robust feature to disable ftrace on start or stop tracing on error

Currently only the initial conversion to nops will disable ftrace
on an anomaly. But if an anomaly happens on start or stopping of the
tracer, it will silently fail.

This patch adds a check there too, to disable ftrace and warn if the
conversion fails.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: let module functions be recorded when dyn ftrace not enabled

When dynamic ftrace had a daemon and a hash to record the locations
of mcount callers at run time, the recording needed to stop when
ftrace was disabled. But now that the recording is done at compile time
and the ftrace_record_ip is only called at boot up and when a module
is loaded, we no longer need to check if ftrace_enabled is set.
In fact, this breaks module load if it is not set because we skip
over module functions.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Because it has goto out before ftrace_list == &ftrace_list_end,
that's to say, we never meet this condition.
Signed-off-by: Nwalimis <walimisdev@gmail.com>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: enable/disable ring buffer recording API added

Several kernel developers have requested that there be a way to stop
recording into the ring buffers with a simple switch that can also
be enabled from userspace. This patch addes a new kernel API to the
ring buffers called:

 tracing_on()
 tracing_off()

When tracing_off() is called, all ring buffers will not be able to record
into their buffers.

tracing_on() will enable the ring buffers again.

These two act like an on/off switch. That is, there is no counting of the
number of times tracing_off or tracing_on has been called.

A new file is added to the debugfs/tracing directory called

  tracing_on

This allows for userspace applications to also flip the switch.

  echo 0 > debugfs/tracing/tracing_on

disables the tracing.

  echo 1 > /debugfs/tracing/tracing_on

enables it.

Note, this does not disable or enable any tracers. It only sets or clears
a flag that needs to be set in order for the ring buffers to write to
their buffers. It is a global flag, and affects all ring buffers.

The buffers start out with tracing_on enabled.

There are now three flags that control recording into the buffers:

 tracing_on: which affects all ring buffer tracers.

 buffer->record_disabled: which affects an allocated buffer, which may be set
     if an anomaly is detected, and tracing is disabled.

 cpu_buffer->record_disabled: which is set by tracing_stop() or if an
     anomaly is detected. tracing_start can not reenable this if
     an anomaly occurred.

The userspace debugfs/tracing/tracing_enabled is implemented with
tracing_stop() but the user space code can not enable it if the kernel
called tracing_stop().

Userspace can enable the tracing_on even if the kernel disabled it.
It is just a switch used to stop tracing if a condition was hit.
tracing_on is not for protecting critical areas in the kernel nor is
it for stopping tracing if an anomaly occurred. This is because userspace
can reenable it at any time.

Side effect: With this patch, I discovered a dead variable in ftrace.c
  called tracing_on. This patch removes it.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>

Impact: add new tracing plugin which can trace full (entry+exit) function calls

This tracer uses the low level function return ftrace plugin to
measure the execution time of the kernel functions.

The first field is the caller of the function, the second is the
measured function, and the last one is the execution time in
nanoseconds.

- v3:

- HAVE_FUNCTION_RET_TRACER have been added. Each arch that support ftrace return
  should enable it.
- ftrace_return_stub becomes ftrace_stub.
- CONFIG_FUNCTION_RET_TRACER depends now on CONFIG_FUNCTION_TRACER
- Return traces printing can be used for other tracers on trace.c
- Adapt to the new tracing API (no more ctrl_update callback)
- Correct the check of "disabled" during insertion.
- Minor changes...
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: fix of output of set_ftrace_filter

Commit ftrace: do not show freed records in available_filter_functions

Removed a bit too much from the set_ftrace_filter code, where we now see
all functions in the set_ftrace_filter file even when we set a filter.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: quick start and stop of function tracer

This patch adds a way to disable the function tracer quickly without
the need to run kstop_machine. It adds a new variable called
function_trace_stop which will stop the calls to functions from mcount
when set.  This is just an on/off switch and does not handle recursion
like preempt_disable().

It's main purpose is to help other tracers/debuggers start and stop tracing
fuctions without the need to call kstop_machine.

The config option HAVE_FUNCTION_TRACE_MCOUNT_TEST is added for archs
that implement the testing of the function_trace_stop in the mcount
arch dependent code. Otherwise, the test is done in the C code.

x86 is the only arch at the moment that supports this.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Impact: corrects a bug which made the non-dyn function tracer not functional

With latest git, the non-dynamic function tracer didn't get any trace.

The problem was the fact that ftrace_enabled wasn't initialized to 1
because ftrace hasn't any init function when DYNAMIC_FTRACE is disabled.

So when a tracer tries to register an ftrace_ops struct,
__register_ftrace_function failed to set the hook.

This patch corrects it by setting an init function to initialize
ftrace during the boot.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

this warning:

  kernel/trace/ftrace.c:189: warning: ‘frozen_record_count’ defined but not used

triggers because frozen_record_count is only used in the KCONFIG_MARKERS
case. Move the variable it there.

Alas, this frozen-record facility seems to have little use. The
frozen_record_count variable is not used by anything, nor the flags.

So this section might need a bit of dead-code-removal care as well.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

fix:

 kernel/trace/ftrace.c: In function 'ftrace_release':
 kernel/trace/ftrace.c:271: error: implicit declaration of function 'ftrace_release_hash'

release_hash is not needed without dftraced.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The ftrace hash was used by the ftrace_daemon code. The record ip function
would place the calling address (ip) into the hash. The daemon would later
read the hash and modify that code.

The hash complicates the code. This patch removes it.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The arch dependent function ftrace_mcount_set was only used by the daemon
start up code. This patch removes it.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The ftrace daemon is complex and error prone.  This patch strips it out
of the code.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Add ftrace warn on to disable ftrace as well as report a warning.

[ Thanks to Andrew Morton for suggesting using the WARN_ON return value ]
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

When an anomaly is detected, we need a way to completely disable
ftrace. Right now we have two functions: ftrace_kill and ftrace_kill_atomic.
The ftrace_kill tries to do it in a "nice" way by converting everything
back to a nop.

The "nice" way is dangerous itself, so this patch removes it and only
has the "atomic" version, which is all that is needed.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Have the ftrace_modify_code return error values:

  -EFAULT on error of reading the address

  -EINVAL if what is read does not match what it expected

  -EPERM  if the write fails to update after a successful match.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The x86 architecture uses a static recording of mcount caller locations
and is not affected by this patch.

For architectures still using the dynamic ftrace daemon, this patch is
critical. It removes the race between the recording of a function that
calls mcount, the unloading of a module, and the ftrace daemon updating
the call sites.

This patch adds the releasing of the hash functions that the daemon uses
to update the mcount call sites. When a module is unloaded, not only
are the replaced call site table update, but now so is the hash recorded
functions that the ftrace daemon will use.

Again, architectures that implement MCOUNT_RECORD are not affected by
this (which currently only x86 has).
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

With the recent updates to ftrace, there should not be any failures when
modifying the code. If there is, then we need to warn about it.

This patch has a cleaned up version of the code that I used to discover
that the weak symbols were causing failures.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

When CONFIG_DYNAMIC_FTRACE isn't used, neither is mcount_addr. This
patch eliminates that warning.
Signed-off-by: NSteven Noonan <steven@uplinklabs.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This must be brown paper bag week for Steven Rostedt!

While working on ftrace for PPC, I discovered that the hash locking done
when CONFIG_FTRACE_MCOUNT_RECORD is not set, is totally incorrect.

With a cut and paste error, I had the hash lock macro to lock for both
hash_lock _and_ hash_unlock!

This bug did not affect x86 since this bug was introduced when
CONFIG_FTRACE_MCOUNT_RECORD was added to x86.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The mcount record method of ftrace scans objdump for references to mcount.
Using mcount as the reference to test if the calls to mcount being replaced
are indeed calls to mcount, this use of mcount was also caught as a
location to change. Using a variable that points to the mcount address
moves this reference into the data section that is not scanned, and
we do not use a false location to try and modify.

The warn on code was what was used to detect this bug.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>