commit 5b7c3c91 introduced an invalid
construct in our CPU selection. This caused warnings, though it still
appeared to do the right thing.

This fixes it properly by having separate formal definitions of
PPC_BOOK3S_32 and PPC_BOOK3S_64 and one statement defining
PPC_BOOK3S based on the two above.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NJames E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add the option to build the code under arch/powerpc with -Werror.

The intention is to make it harder for people to inadvertantly introduce
warnings in the arch/powerpc code. It needs to be configurable so that
if a warning is introduced, people can easily work around it while it's
being fixed.

The option is a negative, ie. don't enable -Werror, so that it will be
turned on for allyes and allmodconfig builds.

The default is n, in the hope that developers will build with -Werror,
that will probably lead to some build breaks, I am prepared to be flamed.

It's not enabled for math-emu, which is a steaming pile of warnings.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds the UPF_FIXED_TYPE flag which will bypass the
8250's autoconfig probe for uart type. The uart type identified
by the of_serial's parse of the flat device tree will be utilized
as defined.
Signed-off-by: NDave Mitchell <dmitchell@amcc.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

probe functions should be __devinit
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The macro spin_event_timeout() takes a condition and timeout value
(in microseconds) as parameters.  It spins until either the condition is true
or the timeout expires.  It returns the result of the condition when the loop
was terminated.

This primary purpose of this macro is to poll on a hardware register until a
status bit changes.  The timeout ensures that the loop still terminates if the
bit doesn't change as expected.  This macro makes it easier for driver
developers to perform this kind of operation properly.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Acked-by: NGeoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If no device is passed to __dma_alloc_coherent, it defaults to using ISA_DMA_THRESHOLD
for the mask. This patch provides a reasonable default rather than 0.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Some XPedite52xx boards have a legacy boot loader requiring some special
care in the boot wrapper.  The use of cuboot-85xx is needed to fix
up embedded device trees, and a custom link address is specified to
accommodate the boot loader and larger kernel image sizes used on X-ES
MPC85xx platforms.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add device tree source files for various MPC85xx boards from Extreme
Engineering Solutions.  Supported boards include XPedite5370,
XPedite5200, XPedite5301, XPedite5330, and XCalibur1501.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for X-ES single-board computers based on the Freescale
MPC85xx processors.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The following series implements basic board support for
the kmeter1 board from keymile, based on a MPC8360.

This series provides the following functionality:

- The board can boot with a serial console on UART1
- Ethernet:
    UCC1 in RGMII mode
    UCC2 in RGMII mode
    UCC4 in RMII mode
    UCC5 in RMII mode
    UCC6 in RMII mode
    UCC7 in RMII mode
    UCC8 in RMII mode

    following patch is necessary for working UCC in RMII mode:

    http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070804.html

- Flash accessed via MTD layer

  On this hardware there is an Intel P30 flash, following patch
  series is necessary for working with this hardware:

  http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070624.html

- I2C using I2C Bus 1 from the MPC8360 cpu
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add 4 partitions in nor flash. Also fix nor flash bank width bug. The
flash is capable of x8/x16 width but is configured for x8.
Signed-off-by: NKevin Hao <kexin.hao@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Currently the fsl,*lbc devices support 8 banks (ie OR and BR registers).
This is adequate for most pq2 and pq3 processors, but not the MPC8280 which
has 12 banks.
Signed-Off-By: NMark Ware <mware@elphinstone.net>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Adding failure path for the following two cases.

warning: ignoring return value of 'device_add', declared with attribute warn_unused_result
warning: ignoring return value of 'sysfs_create_bin_file', declared with attribute warn_unused_result
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Some MPC85xx platforms do support 4 ethernet ports, so make sure the boot
wrapper fixes up all of them in the fdt.

Since MAC addresses are at the end of the bd_t structure there is no harm
in expanding to support 4 MAC address on older 85xx systems that might not
have that many.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

In HW UART mode the TxBD[READY] is not cleared by H/W (RISC engine) when
the user send characters to Tx buffer of QE UART.  So, these characters
stay on the QE forever, never go to UART line.
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Currently the kernel expects the additional four IBAT and DBAT registers
to be available, but doesn't enable these registers on 745x CPUs, which
have them disabled after reset. Thus set the HIGH_BAT_EN bit in HID0
register, if the corresponding MMU feature is defined.
Signed-off-by: NGerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.

The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..

mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.

Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The PCIe MSI interrupts are missing from the device tree source, and
thus were not enabled. This patch adds them.

Tested to work on MPC8315E-RDB with custom FPGA PCIe device.
Signed-off-by: NLeon Woestenberg <leon@sidebranch.com>
Tested-by: NLeon Woestenberg <leon@sidebranch.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Mappings for temperature sensors (adt7461 and lm92) are missing from the
SBC610's DTS file.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

As of commit 40461472 ("Update FSL
esdhc binding"), we use "fsl,esdhc" compatible entry as a base
match. U-Boot will use the same compatible to fixup esdhc nodes.

This patch updates 83xx dts files so that they conform to the new
bindings.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Some boot loaders may not enable L1 instruction/data cache.  Check if
data and instruction caches are enabled, and enable them if needed.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The current device tree for the MPC8272ADS assumes a mapping of 32 MB
of NOR flash at 0xFE00.0000, while there are actually only 8 MB on
the boards, mapped at 0xFF80.0000. When booting an uImage with such a
device tree, the kernel crashes because 0xFE00.0000 is not mapped.

Also introduce aliases for serial[01] and ethernet[01].
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the platform-specific code for enabling SWIOTLB if needed on P2020DS,
MPC85xx DS, and MPC85xx MDS boards as they are capable of having >4G of
memory.

We determine if we need to enable swiotlb based on how much memory is in
the board and if it exceeds 4G or what we can map via PCI inbound
windows.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is the final bit of code to allow enabling swiotlb on
mpc86xx.  The platform-specific code is very small and consists
of enabling SWIOTLB in the config file, registering the
swiotlb_setup_bus_notifier initcall, and setting pci_dma_ops
to point to swiotlb_pci_dma_ops if we have more memory than
can be mapped by the inbound PCI windows.
Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add support for caching, to reduce FLASH wear when writing using small
blocksizes. As we also don't care anymore about heads and tails in case of
partial writes, this greatly simplifies the code for handling writes.

Note: We don't bother caching reads smaller than the FLASH chunk size
(256 KiB).
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently the FLASH database is updated by the kernel using file operations,
meant for userspace only. While this works for us because copy_{from,to}_user()
on powerpc can handle kernel pointers, this is unportable and a bad example.
Replace the file operations by callbacks, registered by the ps3flash driver.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

They were never intended to be exported using EXPORT_SYMBOL() anyway
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It reports the failure of a call to lv1_put_iopte(), not
lv1_map_device_dma_region().
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

probe functions should be __devinit
initialization functions should be __init
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Jim Paris <jim@jtan.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

[Geert: Use ps3_system_bus_[gs]et_driver_data() for ps3_system_bus_device]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jim Paris <jim@jtan.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

So we can kill a cast.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jim Paris <jim@jtan.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>