提交 · 489773c22397c001f54ba4f30856f24407d8d091 · openanolis / cloud-kernel

31 1月, 2012 3 次提交

M
ASoC: wm8993: Convert to use a regmap patch · 489773c2
由 Mark Brown 提交于 1月 31, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
489773c2

ASoC: max9768: Fix up review comments in max9768 driver · 69edea8a

由 Mark Brown 提交于 1月 30, 2012

The Mute Switch should be called Playback Switch to match the volume
and the regmap core has been updated so we don't need to mark all the
registers as non-volatile.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

69edea8a

ASoC: max9768: add driver for max9768 amplifier · 394d2bba

由 Wolfram Sang 提交于 1月 27, 2012

Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

394d2bba

30 1月, 2012 1 次提交
- M
  ASoC: wm2200: Remove trailing whitespace · ffa8d9df
  由 Mark Brown 提交于 1月 29, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  ffa8d9df
28 1月, 2012 1 次提交

ASoC: wm8962: Enable idle_bias_off · 2693efd6

由 Mark Brown 提交于 1月 27, 2012

The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

2693efd6

27 1月, 2012 7 次提交

ASoC: Set idle_bias_off flag in snd_soc_codec_driver · eb3032f8

由 Axel Lin 提交于 1月 27, 2012

Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

eb3032f8

ASoC: wm8994: Report any low impedance accessory as a headphone · 7c08b51f

由 Mark Brown 提交于 1月 26, 2012

Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

7c08b51f

ASoC: wm8996: Handle failures to determine accessory polarity · d7b35570

由 Mark Brown 提交于 1月 26, 2012

If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

d7b35570

ASoC: wm5100: Use pm_runtime for powerdown managment · 62c1c401

由 Mark Brown 提交于 1月 26, 2012

Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

62c1c401

M
ASoC: wm5100: Convert to devm_regulator_bulk_get() · 17e3e57b
由 Mark Brown 提交于 1月 23, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
17e3e57b

ASoC: wm2200: Add WM2200 CODEC driver · d5315a23

由 Mark Brown 提交于 1月 25, 2012

The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

d5315a23

M
ASoC: wm5100: Move regulator supplies over to DAPM infrastructure · 1cf73356
由 Mark Brown 提交于 1月 21, 2012
```
Saves a nice block of code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
1cf73356

25 1月, 2012 3 次提交

ASoC: wm8962: Optimise power consumption for IN4 DC measurement usage · 182c51ce

由 Mark Brown 提交于 1月 24, 2012

When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

182c51ce

M
ASoC: wm5100: Fix warnings from recent patches · 5509f2f8
由 Mark Brown 提交于 1月 24, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
5509f2f8
M
ASoC: Convert the WM5100 revision A updates to a regmap patch · 15b52f10
由 Mark Brown 提交于 1月 21, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
15b52f10

24 1月, 2012 2 次提交
- M
  ASoC: wm5100: Fix mismerge of IRQ frees · e8770dd8
  由 Mark Brown 提交于 1月 24, 2012
```
We only want them at the device level, not at the CODEC level.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  e8770dd8
- M
  ASoC: Convert WM8731 to direct regmap API usage · 05d448e2
  由 Mark Brown 提交于 11月 21, 2011
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  05d448e2
23 1月, 2012 3 次提交

ASoC: Add __devinit/__devexit annotations at necessary places · 5091f5b7

由 Axel Lin 提交于 1月 23, 2012

Fix below build warning when CONFIG_HOTPLUG is not set.

  CC      sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c:1062: warning: ‘alc5623_i2c_remove’ defined but not used
  CC      sound/soc/codecs/alc5632.o
sound/soc/codecs/alc5632.c:1112: warning: ‘alc5632_i2c_remove’ defined but not used
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

5091f5b7

ASoC: sgtl5000: It's sgtl5000 not sgtl500 · 5e0ac527

由 Mark Brown 提交于 1月 23, 2012

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

5e0ac527

ASoC: sgtl5000: Convert to table based DAPM and control init · 89989637

由 Fabio Estevam 提交于 1月 22, 2012

Convert to table based DAPM and control init.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

89989637

22 1月, 2012 8 次提交
- M
  ASoC: wm8988: Convert to devm_kzalloc() · 82fa3670
  由 Mark Brown 提交于 1月 21, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  82fa3670
- M
  ASoC: wm8988: Convert to table based DAPM and control init · dd21353f
  由 Mark Brown 提交于 1月 21, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  dd21353f
- M
  ASoC: wm8985: Convert to direct regmap API usage · 411a3450
  由 Mark Brown 提交于 1月 21, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  411a3450
- M
  ASoC: wm8985 Don't directly reference the cache data structure · 9f8cbae4
  由 Mark Brown 提交于 1月 21, 2012
```
In preparation for conversion to regmap.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  9f8cbae4
- M
  ASoC: wm8985: Use standard cache sync implementation · 8b71d441
  由 Mark Brown 提交于 1月 21, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  8b71d441
- M
  ASoC: wm8985: Convert to table based DAPM and control init · eb8f7693
  由 Mark Brown 提交于 1月 21, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  eb8f7693
- M
  ASoC: wm8985: Convert to devm_kzalloc() · a1fea940
  由 Mark Brown 提交于 1月 21, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  a1fea940
- M
  ASoC: Fix build of tlv320dac33 · 3a4cbf88
  由 Mark Brown 提交于 1月 20, 2012
```
The problem was introduced due to the obscure formatting some of the
older drivers use.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
  3a4cbf88
20 1月, 2012 12 次提交

ASoC: Push WM5100 interrupt request into I2C probe · 09452f23

由 Mark Brown 提交于 1月 18, 2012

This is more what the device model wants us to do and will allow use by
non-audio functions before the audio part of the device has come up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

09452f23

ASoC: Make WM5100 interrupt path use regmap directly · 46c1a877

由 Mark Brown 提交于 1月 18, 2012

This will allow us to move the interrupt allocation out of the ASoC part
of the driver and simplifies the locking by removing any reliance in the
bulk of the interrupt path on the big CODEC lock.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

46c1a877

ASoC: Remove redundant set_bias_level() from WM5100 remove() · 218240e2

由 Mark Brown 提交于 1月 18, 2012

The framework should bring the device down before it calls the driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

218240e2

ASoC: twl4030: Use core to set the msbits constraint · 8819f65c

由 Peter Ujfalusi 提交于 1月 18, 2012

Core can set the msbits constraint in behalf of the dai.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

8819f65c

ASoC: tlv320dac33: Use core to set the msbits constraint · 8d725b2b

由 Peter Ujfalusi 提交于 1月 18, 2012

Core can set the msbits constraint in behalf of the dai.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

8d725b2b

ASoC: sgtl5000: Print revision number in hex · f2c6e757

由 Fabio Estevam 提交于 1月 16, 2012

Throughout the sgtl5000 driver source code and also in the sgtl5000 datasheet
the revision code is shown in hexadecimal.

Print it hex format, for consistency.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

f2c6e757

M
ASoC: Say we can't read WM5100 ID register · 0132615d
由 Mark Brown 提交于 1月 17, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
0132615d

ASoC: When releasing WM5100 put /RESET into reset · 2688738e

由 Mark Brown 提交于 1月 17, 2012

Reset is active low, make sure we leave it asserted when release the
device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

2688738e

M
ASoC: 24 bits are significant on wm_hubs DAIs · 99b0292d
由 Mark Brown 提交于 1月 17, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
99b0292d

ASoC: Make WM8993 I2C usage unconditional · 85f88393

由 Mark Brown 提交于 1月 17, 2012

The WM8993 only supports I2C so don't ifdef the I2C support in the driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

85f88393

ASoC: Implement basic WM8993 interrupt support · 164548d3

由 Mark Brown 提交于 1月 17, 2012

If an interrupt is supplied then use it for thermal warning and FLL lock
notifications. When using the interrupt raise the timeout for the FLL lock
substantially to reduce the chances of spurious warnings.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

164548d3

M
ASoC: 24 bits are significant on the WM8996 audio interfaces · a4b52337
由 Mark Brown 提交于 1月 16, 2012
```
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
```
a4b52337

openanolis / cloud-kernel 1 年多 前同步成功

openanolis / cloud-kernel
1 年多前同步成功