This reverts commit e350e246.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not enabled, the device will be in
ready state.

[jarkko.sakkinen@linux.intel.com: changed pm_runtime_put_sync()
 to pm_runtime_put()]
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinn@linux.intel.com>

There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinn@linux.intel.com>

The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.

The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.

Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'

To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm_transmit() does not check that bufsiz is at least TPM_HEADER_SIZE
before accessing data. This commit adds this check and returns -EINVAL
if it fails.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Constify TPM 1.x header structures in order to move them to rodata
section as they are meant to be never changed during runtime.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Because of the line break in the debug print the chackpatch is
not silent on 80 characters limitation.

The easiest fix is to straighten the lines, it's also more readable.

WARNING: line over 80 characters
+                       FW_BUG "TPM2 ACPI table does not define a memory
resource\n");
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Don't apply endianity conversion when writing to the registers
this is already handled by the system.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Instead of expensive register access on retrieving cmd_size
on each send, save the value during initialization in the private
context. The value doesn't change.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The platform device is not used in this driver, drop the
include to linux/platform_device.h
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Fixes the warning:
drivers/char/tpm/tpm_tis_core.c:443:7: warning: variable ‘itpm’ set but
not used [-Wunused-but-set-variable]
  bool itpm;
       ^~~~
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

CRB_CTRL_CMD_READY and CRB_CTRL_GO_IDLE have incorrect values.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Renamed CRB protocol specific constants to match the TCG PC Client
Platform TPM Profile (PTP) Specification and driver status constants
to be explicit that they are driver specific.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

wmb()'s are not needed as iowrite32() is used.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.

The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:

* Cancel might not happen.
* req_canceled() always returns zero.

A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.

CC: stable@vger.kernel.org
Fixes: 30fc8d13 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Instead of a ad-hoc protocol message construction it is better to
call tpm_pcr_read_dev().
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>

It is better to tpm_transmit_cmd() in tpm2_probe() in order to get
consistent command handling throughout the subsystem.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>

Since tpm_gen_interrupt() is only used in tpm_tis_core.c this commit
replaces it with an internal tpm_tis_gen_interrupt(). The semantics
also changed in a way that on a system error the driver initialization
is failed.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>

Removed unnecessary externs from tpm.h.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>

This function should only be called as part of an IRQ probing protocol
and st33 does not have any code to detect that the IRQ it tries to
generate was not generated and disable the IRQ.

Since st33 is primarily a DT binding driver it should not be doing
IRQ probing anyhow, so let us just delete this useless call.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Unseal and load operations should be done as an atomic operation. This
commit introduces unlocked tpm_transmit() so that tpm2_unseal_trusted()
can do the locking by itself.

Fixes: 0fe54803 ("keys, trusted: seal/unseal with TPM 2.0 chips")
Cc: stable@vger.kernel.org
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>

The driver emits invalid self test error message even though the init
succeeds.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: cae8b441 ("tpm: Factor out common startup code")
Reviewed-by: NJames Morris <james.l.morris@oracle.com>

The command flow is exactly the same, the core simply needs to be
told to enable TPM2 mode when the compatible string indicates a
TPM2.
Signed-off-by: NAndrew Azmansky <andrew.zamansky@nuvoton.com>
Tested-by: NAndrew Zamansky <andrew.zamansky@nuvoton.com>
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The TCG standard startup sequence (get timeouts, tpm startup, etc) for
TPM and TPM2 chips is being open coded in many drivers, move it into
the core code.

tpm_tis and tpm_crb are used as the basis for the core code
implementation and the easy drivers are converted. In the process
several small drivers bugs relating to error handling this flow
are fixed.

For now the flag TPM_OPS_AUTO_STARTUP is optional to allow a staged
driver roll out, but ultimately all drivers should use this flow and
the flag removed. Some drivers still do not implement the startup
sequence at all and will need to be tested with it enabled.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: NAndrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

If devm_add_action() fails we are explicitly calling put_device() to
free the resources allocated. Lets use the helper
devm_add_action_or_reset() and return directly in case of error, as we
know that the cleanup function has been already called by the helper if
there was any error.
Signed-off-by: NSudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

In 570a3609 IRQ path is incorrectly always exercised while it should be
exercised only when there is an IRQ number allocated. This commit
reverts the old behavior.

[jarkko.sakkinen@linux.intel.com: updated description]

Fixes: 570a3609 ("tpm: drop 'irq' from struct tpm_vendor_specific")
Signed-off-by: NAndrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Some chips incorrectly support partial reads from TPM_STS register
at non-zero offsets. Read the entire 32-bits register instead of
making two 8-bit reads to support such devices and reduce the number
of bus transactions when obtaining the burstcount from TPM_STS.

Fixes: 27084efe ("tpm: driver for next generation TPM chips")
Signed-off-by: NAndrey Pronin <apronin@chromium.org>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The result must be converted from BE byte order, which is used by the
TPM2 protocol. This has not popped out because tpm2_get_tpm_pt() has
been only used for probing.

Fixes: 7a1d7e6d ("tpm: TPM 2.0 baseline support")
Change-Id: I7d71cd379b1a3b7659d20a1b6008216762596590
Signed-off-by: NAndrey Pronin <apronin@chromium.org>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm_tis_core was missing conversion from msec when assigning max
timeouts from constants.

Fixes: aec04cbd ("tpm: TPM 2.0 FIFO Interface")
Signed-off-by: NAndrey Pronin <apronin@chromium.org>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

When running make C=2 M=drivers/char/tpm/

  CHECK   drivers/char/tpm//tpm_crb.c
drivers/char/tpm//tpm_crb.c:248:31: warning: incorrect type in return expression (different address spaces)
drivers/char/tpm//tpm_crb.c:248:31:    expected void [noderef] <asn:2>*
drivers/char/tpm//tpm_crb.c:248:31:    got void *

CC: stable@vger.kernel.org
Fixes: 1bd047be ("tpm_crb: Use devm_ioremap_resource")
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>

When running make C=2 M=drivers/char/tpm/

  CC [M]  drivers/char/tpm//tpm_crb.o
  CHECK   drivers/char/tpm//tpm_vtpm_proxy.c
drivers/char/tpm//tpm_vtpm_proxy.c:552:32: warning: incorrect type in assignment (different address spaces)
drivers/char/tpm//tpm_vtpm_proxy.c:552:32:    expected struct vtpm_proxy_new_dev *vtpm_new_dev_p
drivers/char/tpm//tpm_vtpm_proxy.c:552:32:    got void [noderef] <asn:1>*argp
drivers/char/tpm//tpm_vtpm_proxy.c:553:51: warning: incorrect type in argument 2 (different address spaces)
drivers/char/tpm//tpm_vtpm_proxy.c:553:51:    expected void const [noderef] <asn:1>*from
drivers/char/tpm//tpm_vtpm_proxy.c:553:51:    got struct vtpm_proxy_new_dev *vtpm_new_dev_p
drivers/char/tpm//tpm_vtpm_proxy.c:559:34: warning: incorrect type in argument 1 (different address spaces)
drivers/char/tpm//tpm_vtpm_proxy.c:559:34:    expected void [noderef] <asn:1>*to
drivers/char/tpm//tpm_vtpm_proxy.c:559:34:    got struct vtpm_proxy_new_dev *vtpm_new_dev_p

The __user annotation was missing from the corresponding variable.

Fixes: 794c38e01358 ("tpm: Proxy driver for supporting multiple emulated TPMs")
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>

Spi protocol standardized by the TCG is now supported by most of TPM
vendors.

It supports SPI Bit Protocol as describe in the TCG PTP
specification (chapter 6.4.6 SPI Bit Protocol).

Irq mode is not supported.

This commit is based on the initial work by Peter Huewe.
Signed-off-by: NPeter Huewe <peter.huewe@infineon.com>
Signed-off-by: NAlexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

To avoid code duplication between the old tpm_tis and the new and future
native tcg tis driver(ie: spi, i2c...), the tpm_tis driver was reworked,
so that all common logic is extracted and can be reused from all drivers.

The core methods can also be used from other TIS like drivers.

itpm workaround is now managed with a specific tis flag
TPM_TIS_ITPM_POSSIBLE.

This commit is based on the initial work by Peter Huewe.
Signed-off-by: NPeter Huewe <peter.huewe@infineon.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

This splits tpm_tis in a high-level protocol part and a low-level interface
for the actual TPM communication. The low-level interface can then be
implemented by additional drivers to provide access to TPMs using other
mechanisms, for example native I2C or SPI transfers, while still reusing
the same TIS protocol implementation.

Though the ioread/iowrite calls cannot fail, other implementations of this
interface might want to return error codes if their communication fails.

This follows the usual pattern of negative values representing errors and
zero representing success. Positive values are not used (yet).

Errors are passed back to the caller if possible. If the interface of a
function does not allow that, it tries to do the most sensible thing it
can, but this might also mean ignoring the error in this instance.

This commit is based on the initial work by Peter Huewe.
Signed-off-by: NAlexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Split priv_data structure in common and phy specific structures. This will
allow in future patches to reuse the same tis logic on top of new phy such
as spi and i2c. Ultimately, other drivers may reuse this tis logic.
(e.g: st33zp24...)

iobase field is specific to TPM addressed on 0xFED4xxxx on LPC/SPI bus.

This commit is based on the initial work by Peter Huewe.
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Add missing include guards in tpm.h
Signed-off-by: NPeter Huewe <peter.huewe@infineon.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Fix the suspend regression due to the wrong way of retrieving the
chip structure. The suspend functions are attached to the hardware
device, not the chip and thus must rely on drvdata.

Fixes: e89f8b1ade9cc1a ("tpm: Remove all uses of drvdata from the TPM Core")
Reported-by: NJeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: NJeremiah Mahler <jmmahler@gmail.com>
Acked-by: NJarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkine@linux.intel.com>

Fixes: 28157164b056 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The newly added vtpmx driver fails to build if CONFIG_ANON_INODES
is disabled:

drivers/char/built-in.o: In function `vtpmx_fops_ioctl':
(.text+0x97f8): undefined reference to `anon_inode_getfile'

This adds a Kconfig 'select' statement to ensure it's always there
when we need it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 794c38e01358 ("tpm: Proxy driver for supporting multiple emulated TPMs")
Acked-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>