pin_to_mask expects a bank pin number. So do not add the chip base.

Without that patch cat /sys/kernel/debug/gpio looks like that:
GPIOs 0-31, platform/fffff200.gpio, fffff200.gpio:
[spi32766.0] GPIOfffff200.gpio5: [gpio] set
[ads7846_pendown] GPIOfffff200.gpio15: [gpio] set
[ohci_vbus] GPIOfffff200.gpio21: [gpio] set
[ohci_vbus] GPIOfffff200.gpio24: [gpio] set
[button1] GPIOfffff200.gpio28: [gpio] clear
[button2] GPIOfffff200.gpio29: [gpio] clear

GPIOs 32-63, platform/fffff400.gpio, fffff400.gpio:
[sda] GPIOfffff400.gpio4: [periph A]
[scl] GPIOfffff400.gpio5: [periph A]
[spi32766.3] GPIOfffff400.gpio11: [periph A]
[error] GPIOfffff400.gpio22: [periph A]
[run] GPIOfffff400.gpio23: [periph A]

GPIOs 64-95, platform/fffff600.gpio, fffff600.gpio:
[reset_pin] GPIOfffff600.gpio29: [periph A]

GPIOs 96-127, platform/fffff800.gpio, fffff800.gpio:
[led1] GPIOfffff800.gpio5: [periph A]
[led2] GPIOfffff800.gpio6: [periph A]
[led3] GPIOfffff800.gpio7: [periph A]
[led4] GPIOfffff800.gpio8: [periph A]

GPIOs 128-159, platform/fffffa00.gpio, fffffa00.gpio:
[button3] GPIOfffffa00.gpio10: [periph A]
[button4] GPIOfffffa00.gpio12: [periph A]

Note that every bank despite bank 0 only shows "periph A" which are
obviously used as GPIOs.
Signed-off-by: NAlexander Stein <alexanders83@web.de>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This converts the AT91 pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: NAlexander Stein <alexanders83@web.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The kerneldoc for struct tegra_pingroup didn't describe all of the fields
in the struct. Add some extra kerneldoc to fix that.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When an attempt is made to configure an unsupported option on a pin,
print the DT property name of that option, so it's easier to debug
what the problem is.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The range of npins and function ID values is small enough to fit into a
u8. Use this type rather than unsigned to shrink the pinmux data tables.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The fsafe value in the pingroup data tables is only used to implement
tegra_pinctrl_disable(). The only reason this function is called is when
dynamically switching between pinmux states, i.e. when disabling the old
state before programming the new state. It's simpler to have the new
target state define the expected value of each pin (and all current DTs
do that). This also gives more flexibility, since it allows individual
boards explicit control over the "inactive" mux function for each pin,
rather than requiring it to be an SoC-specific value. Assuming this, we
can get rid of the fsafe value from the driver completely, thus saving
some more space in the driver tables.

While re-writing the content of tegra124_pingroups[], fix the indentation
to use a TAB instead of spaces.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Any SoC which supports the einput, odrain, lock, ioreset, or rcv_sel
options has the relevant HW register fields in the same register as the
mux function selection. Similarly, the drvtype option is always in the
drive register, if it is supported at all. Hence, we don't need to have
struct *_reg fields in the pin group table to define which register and
bank to use for those options. Delete this to save space in the driver's
data tables.

However, many of those options are not supported on all SoCs, or not
supported on some pingroups. We need a way to detect when they are
supported. Previously, this was indicated by setting the struct *_reg
field to -1. With the struct *_reg fields removed, we use the struct
*_bit fields for this purpose instead. The struct *_bit fields need to
be expanded from 5 to 6 bits in order to store a value outside the valid
HW bit range of 0..31.

Even without removing the struct *_reg fields, we still need to add code
to validate the struct *_bit fields, since some struct *_bit fields were
already being set to -1, without an option-specific struct *_reg field to
"guard" them. In other words, before this change, the pinmux driver might
allow some unsupported options to be written to HW.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add the muxing for the last missing i2c rcar core. Fix the sorting for
SH_PFC_PIN_NAMED while we are here.
Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

With debug enabled we get better readability dumps of the mux_mode register if
we use hexadecimal format instead:

imx6sl-pinctrl 20e0000.iomuxc: MX6SL_PAD_FEC_REF_CLK: 0x10 0x0001b0a8
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Reviewed-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

According to the MODULE_AUTHOR() comments, the author name should be
"Name <email>" or just "Name". Add the missing '>'.
Signed-off-by: NAntoine Ténart <antoine.tenart@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When using a group only pinctrl driver, which does not have any
information on the pins it is useless to define a get_group_pins
always returning an empty list of pins.

When not using get_group_pin[1], a driver must implement it so
pins = NULL and num_pins = 0. This patch makes it the default
behaviour if not defined in the pinctrl driver when used in
pinmux enable and disable funtions and in pinctrl_groups_show.

It also adds a check in pinctrl_get_group_pins and return -EINVAL if
not defined. This function is called in the gpiolib when adding when
pingroup range. It cannot be used if no group is defined, so this seams
reasonable.

[1] get_group_pin(struct pinctrl_dev *pctldev,
		  unsigned selector,
		  const unsigned **pins,
		  unsigned *num_pins);
Signed-off-by: NAntoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The A31 SoC has PL and PM banks and thus increase the default ARCH_NR_GPIO.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The A31 SoC define a reset line for the R_PIO block which needs to be
deasserted.

Try to retrieve a reset control and deassert if one was found.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The A31 SoC provides both PL and PM pio bank through the R_PIO block.

These pins all support gpio function and can bbe assigned to system
peripherals (like TWI, P2WI, JTAG, ...)
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add support for multiple pin controller instances.

First remove the static definition of the sunxi gpio chip struct and fill
the dynamically struct instead.
Then define a new pin_base field in the sunxi_pinctrl_desc which will be
used to specify the gpiochip base pin.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Define PL and PM pin macros.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Disable the clk when failing to probe the pin controller device.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Check the clk_prepare_enable return value to avoid false positive probe.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch completes the one that used ARRAY_SIZE for STiH407 and STiH416
for setting ninput_delays and noutput_delays fields.
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds const qualifier where applicable.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Define __PINCTRL_LANTIQ_H to prevent multiple inclusion.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It's only referenced in this file, make it static.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The DU parallel interface ODDF signal is optional, move it out of the
HSYNC/VSYNC group into a group of its down. The CDE and DISP signals are
independent, split them to two different groups.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This driver is only useful on MSM8x74, so let the driver depend on
ARCH_QCOM but allow compile coverage testing.
The main benefit is that the driver isn't available to be selected for
machines that don't have the matching hardware.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm APQ8064 platform.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

DT bindingdocumentation for qcom,apq8064-pinctrl driver.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The various pins may have different number of functions defined, so make this
number definable per pin instead of just increasing it to the largest one for
all of the platforms.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This lets the gpiolib core handle the irqchip set-up and
chained IRQ on the primary (behind the mux) IRQ chip in
the st pinctrl driver.

Default irq type is set to level low at irqchip add time.

The v1 was sent by Linus
(https://lkml.org/lkml/2014/4/4/287).

Two changes were necessary to make it to work properly
on STiH416:
  1 - dev reference was not passed to the gpio_chip
      struct, causing a panic.
  2 - gpiochip_irqchip_add passed IRQ_TYPE_NONE as
      default type, which caused lot of warnings at
      init time. I choose IRQ_TYPE_LEVEL_LOW as default.

Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMaxime COQUELIN <maxime.coquelin@st.com>

In the mass-conversion to the new irqchip callbacks, this
in-transit IRQ support was missed. Fix it.

Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Maxime COQUELIN <maxime.coquelin@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pull slave-dmaengine fixes from Vinod Koul:
 "Back from long weekend here in India and now the time to send fixes
  for slave dmaengine.
   - Dan's fix of sirf xlate code
   - Jean's fix for timberland
   - edma fixes by Sekhar for SG handling and Yuan for changing init
     call"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: fix eDMA driver as a subsys_initcall
  dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
  platform: Fix timberdale dependencies
  dma: edma: fix incorrect SG list handling

Pull iommu fixes from Joerg Roedel:
 "Fixes for regressions:

   - fix wrong IOMMU enumeration causing some SCSI device drivers
     initialization failures
   - ARM-SMMU fixes for a panic condition and a wrong return value"

* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
  iommu/arm-smmu: Return 0 on unmap failure
  iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
  iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
  iommu/vt-d: fix memory leakage caused by commit ea8ea460

Pull perf tooling fixes from Ingo Molnar:
 "Three small tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Improve error reporting
  perf tools: Adjust symbols in VDSO
  perf kvm: Fix 'Min time' counting in report command

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf into perf/urgent

Pull perf/urgent fixes from Jiri Olsa:

User visible changes:

  * Adjust symbols in VDSO to properly resolve its function names (Vladimir Nikulichev)

  * Improve error reporting for record session failure (Adrien BAK)

  * Fix 'Min time' counting in report command (Alexander Yarygin)
Signed-off-by: NJiri Olsa <jolsa@redhat.com>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

In the current version, when using perf record, if something goes
wrong in tools/perf/builtin-record.c:375
  session = perf_session__new(file, false, NULL);

The error message:
"Not enough memory for reading per file header"

is issued. This error message seems to be outdated and is not very
helpful. This patch proposes to replace this error message by
"Perf session creation failed"

I believe this issue has been brought to lkml:
https://lkml.org/lkml/2014/2/24/458
although this patch only tackles a (small) part of the issue.

Additionnaly, this patch improves error reporting in
tools/perf/util/data.c open_file_write.

Currently, if the call to open fails, the user is unaware of it.
This patch logs the error, before returning the error code to
the caller.
Reported-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NAdrien BAK <adrien.bak@metascale.org>
Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast
[ Reorganize the changelog into paragraphs ]
[ Added empty line after fd declaration in open_file_write ]
Signed-off-by: NJiri Olsa <jolsa@redhat.com>

pert-report doesn't resolve function names in VDSO:

$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
            8.76%
               0x7fff6b1fe861
               __gettimeofday
               ACE_OS::gettimeofday()
...

In this case symbol values should be adjusted the same way as for executables,
relocatable objects and prelinked libraries.

After fix:

$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
            8.76%
               __vdso_gettimeofday
               __gettimeofday
               ACE_OS::gettimeofday()
Signed-off-by: NVladimir Nikulichev <nvs@tbricks.com>
Tested-by: NNamhyung Kim <namhyung@kernel.org>
Reviewed-by: NAdrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvsSigned-off-by: NJiri Olsa <jolsa@redhat.com>

Every event in the perf-kvm has a 'stats' structure, which contains
max/min/average/etc times of handling this event.
The problem is that the 'perf-kvm stat report' command always shows
that 'min time' is 0us for every event. Example:

 # perf kvm stat report

 Analyze events for all VCPUs:

    VM-EXIT    Samples  Samples%     Time%   Min Time   Max Time Avg time
  [..]
  0xB2 MSCH         12     0.07%     0.00%        0us        8us 7.31us ( +-   2.11% )
  0xB2 CHSC         12     0.07%     0.00%        0us       18us 9.39us ( +-   9.49% )
  0xB2 STPX          8     0.05%     0.00%        0us        2us 1.88us ( +-   7.18% )
  0xB2 STSI          7     0.04%     0.00%        0us       44us 16.49us ( +-  38.20% )
  [..]

This happens because the 'stats' structure is not initialized and
stats->min equals to 0. Lets initialize the structure for every
event after its allocation using init_stats() function. This initializes
stats->min to -1 and makes 'Min time' statistics counting work:

 # perf kvm stat report

 Analyze events for all VCPUs:

    VM-EXIT    Samples  Samples%     Time%   Min Time   Max Time Avg time
  [..]
  0xB2 MSCH         12     0.07%     0.00%        6us        8us 7.31us ( +-   2.11% )
  0xB2 CHSC         12     0.07%     0.00%        7us       18us 9.39us ( +-   9.49% )
  0xB2 STPX          8     0.05%     0.00%        1us        2us 1.88us ( +-   7.18% )
  0xB2 STSI          7     0.04%     0.00%        1us       44us 16.49us ( +-  38.20% )
  [..]
Signed-off-by: NAlexander Yarygin <yarygin@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1397053319-2130-3-git-send-email-borntraeger@de.ibm.com
[ Fixing the perf examples changelog output ]
Signed-off-by: NJiri Olsa <jolsa@redhat.com>