This patch adds TMU platform data for sh7723. Both clockevent
and clocksource support is enabled. While at it, adjust the
CMT clocksource rating to prioritize the TMU.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch enables the TMU clocksource on sh7722.
To prioritize TMU over CMT we also adjust the CMT
clock source rating.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch updates the clock framework use count code.
With this patch the enable() and disable() callbacks
only get called when counting from and to zero.
While at it the kref stuff gets replaced with an int.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This moves out the cayman-specific panic handler code to a better
location, and leaves the generic implementation a simple stub that is
still used under emulation.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

None of the print_page() code and associated helpers are presently used
by anything in-tree, so just kill it off.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is no longer necessary, as there are now sufficient generic
alternatives available.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that all of the possible users for rtc_lock have gone away, it is no
longer necessary to keep this lock definition around.

This follows several other architectures that have either recently
dropped it or never supported it in the first place.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This converts the sh03 rtc code off of using the global rtc_lock and on
to its own spinlock. There are no other possible users of the rtc_lock,
so serializing with it is not necessary.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

With the conversion to generic clockevents these are completely unused,
so just kill it off.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Nothing is using this anymore now that we have fully converted to generic
time, so kill it off completely.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that everything has converted over to generic timekeeping, we need an
alternate method for keeping the RTC updated for those platforms that are
still using the rtc_sh_get/set_time pairs, presently limited to SH-03 and
the Dreamcast. This wires up the GENERIC_CMOS_UPDATE hooks for those to
maintain the same behaviour.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is now fully generic, and used both by _32 and _64 variants.
Rename it accordingly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds sh_tmu support to the SH-5 subtypes, which subsequently allows
us to kill off time_64.c and use the now generic time_32.c. As a bonus,
SH-5 now supports highres timers and tickless for the first time.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that the onchip_remap() mess is sorted out, the rtc-sh support code
for SH-5 can follow the same approach as the other CPUs.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The TMU block is supported on all SH-3 and SH-4 subtypes, so just select
it there, rather than conditionalizing it per subtype.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds TMU platform data for sh7785. Both clockevent
and clocksource support is enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update the r7785 highlander defconfig to fix
PCLK value and that mode4 is set high.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make sure that clk->ops->init() only gets called once in
the case of CLK_ALWAYS_ENABLED. Without this patch the
init() callback may be called multiple times.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch moves the SH4 case of EARLY_SCIF_CONSOLE_PORT
so the SH7785 default value gets used. Without this patch
the value for SH7785 is set to 0xffe80000.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

sh64 is still using this, so re-enable it temporarily while SH-5 gets
converted to use the generic code.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Presently shm_align_mask is only looked at for the bottom up case, but we
still want this for proper colouring constraints in the topdown case.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There still seems to be some stack corruption to sort out here, so flag
this as BROKEN until this issue is sorted out.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The old arch/sh/kernel/timers/ directly will be going away completely
once the rest of the TMU users are migrated, so move the dummy broadcast
driver up a level in preparation.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that the stragglers (MTU2/CMT/etc.) have been rewritten and we are
selecting both GENERIC_TIME and GENERIC_CLOCKEVENTS, the get_offset()
timer op is completely unused. As a result, we are now able to kill off
the ARCH_USES_GETTIMEOFFSET references.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that the rest of the timers that didn't support clockevents have been
rewritten, both of these can be enabled by default.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Neither of these need to be exported, so just make them static.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

All of the SH timers use a roughly identical structure for platform data,
which presently is broken out for each block. Consolidate all of these
definitions, as there is no reason for them to be broken out in the first
place.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds TMU platform data for sh7722. Only clockevent
mode is enabled for now, clocksource requires this patch:
"clocksource: setup mult_orig in clocksource_enable()"
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds a TMU driver for the SuperH architecture.

The TMU driver is a platform driver with early platform
support to allow using a TMU channel as clockevent or
clocksource during system bootup or later.

Clocksource or clockevent can be selected.
Both periodic and oneshot clockevents are supported.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes the old MTU2 driver (CONFIG_SH_MTU2/timer-mtu2.c)

As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_MTU2
and configure timer channel using platform data.

If multiple MTU channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_mtu2.0" to select the first channel.

To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds MTU2 platform data for the following cpus:
 - sh7201 (3/5 channels)
 - sh7203/sh7263 (2/4 channels)
 - sh7206 (3/5 channels)
 - MXG (3/5 channels)
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds a MTU2 driver for the SuperH architecture.

The MTU2 driver is a platform driver with early platform
support to allow using a MTU2 channel as only clockevent
during system bootup.

Clocksource on sh2a is currently unsupported due to code
generation issues with 64-bit math, so at this point only
periodic clockevent support is in place.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert sh to use GENERIC_TIME via the arch_getoffset() infrastructure.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Impact: cleanup

Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Impact: cleanup

convert the last remaining users to no_irq_chip
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Merge branch 'timers/clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip

Some arches don't supply their own clocksource. This is mainly the
case in architectures that get their inter-tick times by reading the
counter on their interval timer.  Since these timers wrap every tick,
they're not really useful as clocksources.  Wrapping them to act like
one is possible but not very efficient. So we provide a callout these
arches can implement for use with the jiffies clocksource to provide
finer then tick granular time.

[ Impact: ease the migration to generic time keeping ]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Setup clocksource mult_orig in clocksource_enable().

Clocksource drivers can save power by using keeping the
device clock disabled while the clocksource is unused.

In practice this means that the enable() and disable()
callbacks perform clk_enable() and clk_disable().

The enable() callback may also use clk_get_rate() to get
the clock rate from the clock framework. This information
can then be used to calculate the shift and mult variables.

Currently the mult_orig variable is setup from mult at
registration time only. This is conflicting with the above
case since the clock is disabled and the mult variable is
not yet calculated at the time of registration.

Moving the mult_orig setup code to clocksource_enable()
allows us to both handle the common case with no enable()
callback and the mult-changed-after-enable() case.

[ Impact: allow dynamic clock source usage ]
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
LKML-Reference: <20090501054546.8193.10688.sendpatchset@rx1.opensource.se>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>