- 03 1月, 2009 14 次提交
-
-
由 Dmitri Belimov 提交于
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Dmitri Belimov 提交于
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Dmitri Belimov 提交于
Fix I2C bridge error in zl10353 if no tunner attached to internal I2C bus of zl10353 chip. When set enable bridge from internal I2C bus to the main I2C bus (saa7134) the main I2C bus stopped very hardly. No any communication. In our next board we solder additional resistors to internal I2C bus. Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mike Frysinger 提交于
Since ttusb_dec.c relies on pci_alloc_consistent and pci_free_consistent, make it depend on PCI in Kconfig. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mike Frysinger 提交于
Since dvb-ttusb-budget.c relies on pci_alloc_consistent and pci_free_consistent, make it depend on PCI in Kconfig. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 roel kluin 提交于
Unsigned cx23417_mailbox cannot be negative Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Cyrill Gorcunov 提交于
Add missed MODULE check to eliminate inapropriate declaration being choosed which causes a build error. Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Since the i2c driver ID will be removed in the near future we have to modify the v4l2 debugging API to use the driver name instead of driver ID. Note that this API is not used in applications other than v4l2-dbg.cpp as it is for debugging and testing only. Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged with a warning that it is deprecated and will be removed in 2.6.30. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
This rename prevents conflicts with the older compat_ioctl32 module. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Since internal to v4l2 the ioctl prototype is the same regardless of it being called through .ioctl or .unlocked_ioctl, we need to convert it all to the long return type of unlocked_ioctl. Thanks to Jean-Francois Moine for posting an initial patch for this and thus bringing it to our attention. Cc: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Add CONFIG_COMPAT check in Makefile. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Introduce a struct v4l2_file_operations for v4l2 drivers. Remove the unnecessary inode argument. Move compat32 handling (and llseek) into the v4l2-dev core: this is now handled in the v4l2 core and no longer in the drivers themselves. Note that this changeset reverts an earlier patch that changed the return type of__video_ioctl2 from int to long. This change will be reinstated later in a much improved version. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 01 1月, 2009 1 次提交
-
-
由 Nick Piggin 提交于
struct dentry is one of the most critical structures in the kernel. So it's sad to see it going neglected. With CONFIG_PROFILING turned on (which is probably the common case at least for distros and kernel developers), sizeof(struct dcache) == 208 here (64-bit). This gives 19 objects per slab. I packed d_mounted into a hole, and took another 4 bytes off the inline name length to take the padding out from the end of the structure. This shinks it to 200 bytes. I could have gone the other way and increased the length to 40, but I'm aiming for a magic number, read on... I then got rid of the d_cookie pointer. This shrinks it to 192 bytes. Rant: why was this ever a good idea? The cookie system should increase its hash size or use a tree or something if lookups are a problem. Also the "fast dcookie lookups" in oprofile should be moved into the dcookie code -- how can oprofile possibly care about the dcookie_mutex? It gets dropped after get_dcookie() returns so it can't be providing any sort of protection. At 192 bytes, 21 objects fit into a 4K page, saving about 3MB on my system with ~140 000 entries allocated. 192 is also a multiple of 64, so we get nice cacheline alignment on 64 and 32 byte line systems -- any given dentry will now require 3 cachelines to touch all fields wheras previously it would require 4. I know the inline name size was chosen quite carefully, however with the reduction in cacheline footprint, it should actually be just about as fast to do a name lookup for a 36 character name as it was before the patch (and faster for other sizes). The memory footprint savings for names which are <= 32 or > 36 bytes long should more than make up for the memory cost for 33-36 byte names. Performance is a feature... Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
- 31 12月, 2008 6 次提交
-
-
由 Roland Dreier 提交于
Commit f780a9f1 ("mlx4_core: Add ethernet fields to CQE struct") introduced a bug in how wc->sl is set in mlx4_ib_poll_one() -- since cqe->sl_vid is a big-endian value, the shift must be done after converting to host endianness. This bug was found using sparse endianness checking. Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 James Bottomley 提交于
fcoe selects libfc and requires SCSI and PCI (the SCSI requirement is implicitly covered by an enclosing if). Fix them both up so they cannot be configured in an invalid state: make LIBFC select SCSI_FC_ATTRS and make FCOE depend on PCI and select LIBFC. Reported-by: NRandy Dunlap <randy.dunlap@oracle.com> Cc: Robert Love <robert.w.love@intel.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 James Bottomley 提交于
cxgb3i requires the cxgb3 net driver, so it selects it. However, cxgb3 has dependencies which the select cannot see. Fix this by separating out the cxgb3 dependencies into a separate hidden config option (CONFIG_CHELSIO_T3_DEPENDS) and make both cxgb3 and cxgb3i depend on it. Reported-by: NRandy Dunlap <randy.dunlap@oracle.com> Cc: Karen Xie <kxie@chelsio.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 James Bottomley 提交于
This structure may not be defined if CONFIG_MODULE=n, so never deref it. Change uses of module->name to module_name(module) and corrects some dyslexic printks and docbook comments. Reported-by: NRandy Dunlap <randy.dunlap@oracle.com> Cc: Robert Love <robert.w.love@intel.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Karen Xie 提交于
The cxgb3i was using skb->sp pointer for some internal book-keeping which is not related to the secure path. Changed it to use skb->cb[] instead. Reported-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NKaren Xie <kxie@chelsio.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
由 Karen Xie 提交于
This patch implements the cxgb3i iscsi connection acceleration for the open-iscsi initiator. The cxgb3i driver offers the iscsi PDU based offload: - digest insertion and verification - payload direct-placement into host memory buffer. Signed-off-by: NKaren Xie <kxie@chelsio.com> Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
-
- 30 12月, 2008 19 次提交
-
-
由 Julia Lawall 提交于
This set of patches introduces calls to the following set of functions: usb_endpoint_dir_in(epd) usb_endpoint_dir_out(epd) usb_endpoint_is_bulk_in(epd) usb_endpoint_is_bulk_out(epd) usb_endpoint_is_int_in(epd) usb_endpoint_is_int_out(epd) usb_endpoint_is_isoc_in(epd) usb_endpoint_is_isoc_out(epd) usb_endpoint_num(epd) usb_endpoint_type(epd) usb_endpoint_xfer_bulk(epd) usb_endpoint_xfer_control(epd) usb_endpoint_xfer_int(epd) usb_endpoint_xfer_isoc(epd) In some cases, introducing one of these functions is not possible, and it just replaces an explicit integer value by one of the following constants: USB_ENDPOINT_XFER_BULK USB_ENDPOINT_XFER_CONTROL USB_ENDPOINT_XFER_INT USB_ENDPOINT_XFER_ISOC An extract of the semantic patch that makes these changes is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r1@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) == - \(USB_ENDPOINT_XFER_CONTROL\|0\)) + usb_endpoint_xfer_control(epd) @r5@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) == - \(USB_DIR_IN\|0x80\)) + usb_endpoint_dir_in(epd) // </smpl> Signed-off-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Steven Rostedt 提交于
Impact: clean up RW_LOCK_UNLOCKED is deprecated. This patch replaces it with the __RW_LOCK_UNLOCKED(lock) macro. This change was a little trickier than others due to the macro being used in another macro that fills an array. Signed-off-by: NSteven Rostedt <srostedt@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Erik Andrén 提交于
As pointed by gcc: drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c: In function ‘hdcs_set_size’: drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c:301: warning: ‘y’ may be used uninitialized in this function Signed-off-by: NErik Andrén <erik.andren@gmail.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
The current code was trying to query the AC97 registers for the vendor information even if it was clearly not a AC97 audio device (resulting in errors in the dmesg output). This was due to a bug in the way we did the check. Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Add additional output formats, which will be useful for the Pinnacle PCTV Ultimate 880e integration with the saa7136. Thanks to Ray Lu from Empia for providing the em2860/em2880 datasheet. Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Noticed when doing the audio support for the Pinnacle PCTV HD Ultimate 808e that the modes were incorrect (the 808e uses I2S in 5 sample mode) Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet. Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Like the em2874, the em2870 does not have any analog support, so don't bother loading the em28xx-alsa module. Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
The Pinnacle 80e cannot be supported since Micronas yanked their driver support for the drx-j chipset at the last minute. Remove the device profile since it cannot work without the drx driver and it being there is only likely to confuse people into thinking the device is supported but not working. Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
The DVC 100 profile is redundant since we already have an existing identical profile named "Pinnacle Dazzle DVC 90/DVC 100" Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Correct problem introduced during the board refactoring where the XCLK frequency would get zero'd out. The sequence of events was as follows: em28xx_pre_card_setup() called em28xx_set_model() em28xx_set_model() would memcpy to dev->board configuration em28xx_pre_card_setup() would set the dev->board.xclk if not set em28xx_pre_card_setup() would set the XCLK register based on dev->board.xclk ... em28xx_card_setup() would call em28xx_set_model() em28xx_set_model() would memcpy to dev->board configuration (clearing out value of dev->board.xclk set in em28xx_pre_card_setup) ... em28xx_audio_analog_set() sets the XCLK register based on dev->board.xclk (which now contains zero) The change sets the default XCLK and I2C Clock fields in the board definition inside of em28xx_set_model() so that subsequent calls do not cause the values to be overwritten. Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
Fix this warning: drivers/media/video/zoran/zoran_card.c:156: warning: ‘zr36067_pci_tbl’ defined but not used Currently, zoran driver relies on a find routine that doesn't use the pci table. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_set_coeff’: drivers/media/dvb/frontends/af9013.c:231: warning: ‘ns_coeff2_8k’ may be used uninitialized in this function drivers/media/dvb/frontends/af9013.c:230: warning: ‘ns_coeff2_2k’ may be used uninitialized in this function drivers/media/dvb/frontends/af9013.c:229: warning: ‘ns_coeff1_8193nu’ may be used uninitialized in this function drivers/media/dvb/frontends/af9013.c:228: warning: ‘ns_coeff1_8192nu’ may be used uninitialized in this function drivers/media/dvb/frontends/af9013.c:227: warning: ‘ns_coeff1_8191nu’ may be used uninitialized in this function drivers/media/dvb/frontends/af9013.c:226: warning: ‘ns_coeff1_2048nu’ may be used uninitialized in this function drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_snr’: drivers/media/dvb/frontends/af9013.c:1012: warning: ‘snr_table’ may be used uninitialized in this function Cc: Antti Palosaari <crope@iki.fi> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
This is needed to sync with the development tree. Probably, a merge conflict were solved by adding this blank line. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
drivers/media/video/usbvideo/quickcam_messenger.c: In function ‘qcm_sensor_init’: drivers/media/video/usbvideo/quickcam_messenger.c:450: warning: operation on ‘ret’ may be undefined Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
This patch fixes this warning: drivers/media/video/gspca/gspca.c:1811: warning: initialization from incompatible pointer type The reason is that the returned argument should be a long, not an integer. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
drivers/media/dvb/dvb-usb/anysee.c: In function ‘anysee_master_xfer’: drivers/media/dvb/dvb-usb/anysee.c:156: warning: ‘ret’ may be used uninitialized By looking at the function, altrough very unlikely, this might eventually be true if num = 0. So, better to fix the warning by initializing with ret = 0. Cc: Antti Palosaari <crope@iki.fi> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Laurent Pinchart 提交于
Extend the range of supported UVC devices by allowing video output devices matching the following structure: TT_STREAMING -> VC_PROCESSING_UNIT -> VC_EXTENSION_UNIT{0,n} -> OTT_* Video output devices are reported with the V4L2_CAP_VIDEO_OUTPUT capability flag and are subject to the same restrictions as video input devices. Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Laurent Pinchart 提交于
Built-in iSight webcams have an interrupt endpoint but spit proprietary data that don't conform to the UVC status endpoint messages. Don't try to handle the interrupt endpoint for those cameras. Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Laurent Pinchart 提交于
When the first bulk URB of a video payload contains an erroneous header, or when no V4L2 buffer is available, the whole payload must be dropped. Change the skip logic to drop all bulk URBs until the end of the payload instead of the first one only. Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-