This reverts commit b7d5b439.
It conflicts with commit baab93af "USB:
EHCI: ASPM quirk of ISOC on AMD Hudson" and merging the two just doesn't
work properly.

Cc: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The pre-release GCC-4.6 now correctly flags this code as dead.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.

AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:

1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
   in low power state is enabled.

Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.

Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:

1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
   make them cleaner;
2. AMD chipset information will be probed only once and then stored.
   Currently they're probed during every OHCI/EHCI initialization, move
   the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
   code, every host controller enable/disable PLL only according to
   its own status, and may enable PLL while there is still isoc transfer on
   other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When ASPM PM Feature is enabled on UMI link, devices that use ISOC stream of
data transfer may be exposed to longer latency causing less than optimal per-
formance of the device. The longer latencies are normal and are due to link
wake time coming out of low power state which happens frequently to save
power when the link is not active.
The following code will make exception for certain features of ASPM to be by
passed and keep the logic normal state only when the ISOC device is connected
and active. This change will allow the device to run at optimal performance
yet minimize the impact on overall power savings.
Signed-off-by: NAlex He <alex.he@amd.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On AMD SB700/SB800/Hudson-2/3 platforms, USB EHCI controller may read/write
to memory space not allocated to USB controller if there is longer than
normal latency on DMA read encountered. In this condition the exposure will
be encountered only if the driver has following format of Periodic Frame
List link pointer structure:

For any idle periodic schedule, the Frame List link pointers that have the
T-bit set to 1 intending to terminate the use of frame list link pointer
as a physical memory pointer.

Idle periodic schedule Frame List Link pointer shoule be in the following
format to avoid the issue:

Frame list link pointer should be always contains a valid pointer to a
inactive QHead with T-bit set to 0.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1409) removes some dead code from the ehci-hcd
scheduler.  Thanks to the previous patch in this series, stream->depth
is no longer used.  And stream->start and stream->rescheduled
apparently have not been used for quite a while, except in some
statistics-reporting code that never gets invoked.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1408) rearranges the scheduling code in ehci-hcd, partly
to improve its structure, but mainly to change the way it works.
Whether or not a transfer exceeds the hardware schedule length will
now be determined by looking at the last frame the transfer would use,
instead of the first available frame following the end of the transfer.

The benefit of this change is that it allows the driver to accept
valid URBs which would otherwise be rejected.  For example, suppose
the schedule length is 1024 frames, the endpoint period is 256 frames,
and a four-packet URB is submitted.  The four transfers would occupy
slots that are 0, 256, 512, and 768 frames past the current frame
(plus an extra slop factor).  These don't exceed the 1024-frame limit,
so the URB should be accepted.  But the current code notices that the
next available slot would be 1024 frames (plus slop) in the future,
which is beyond the limit, and so the URB is rejected unnecessarily.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1407) fixes a bug in ehci-hcd's isochronous scheduler.
All its calculations should be done in terms of microframes, but for
full-speed devices, sched->span is stored in frames.  It needs to be
converted.

This fix is liable to expose problems in other drivers.  The old code
would accept URBs that should not have been accepted, so drivers have
had no reason to avoid submitting URBs that exceeded the maximum
schedule length.  In an attempt to partially compensate for this, the
patch also adjusts the schedule length from a minimum of 256 frames up
to a minimum of 512 frames.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1406) adds a micro-optimization to ehci-hcd's scheduling
code.  Instead of computing remainders with respect to the schedule
length, use bitwise-and (which is quicker).  We know that the schedule
length will always be a power of two, but the compiler doesn't have
this information.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1405) fixes a small bug in ehci-hcd's isochronous
scheduler.  Not all EHCI controllers are PCI, and the code shouldn't
assume that they are.  Instead, introduce a special flag for
controllers which need to delay iso scheduling for full-speed devices
beyond the scheduling threshold.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: David Brownell <david-b@pacbell.net>
CC: stable <stable@kernel.org>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags.  This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.

The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.

(Strictly speaking, the authorized_default flag should become atomic
as well.  I didn't bother with it because it gets changed only via
sysfs.  It can be done later, if anyone wants.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1369) fixes a problem in ehci-hcd.  Some controllers
occasionally run into trouble when the driver reclaims siTDs too
quickly.  This can happen while streaming audio; it causes the
controller to crash.

The patch changes siTD reclamation to work the same way as iTD
reclamation: Completed siTDs are stored on a list and not reused until
at least one frame has passed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NNate Case <ncase@xes-inc.com>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.

After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.

This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-by: NColin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When isochronous URBs are shorter than one frame and when more than one
ITD in a frame has been completed before the interrupt can be handled,
scan_periodic() completes the URBs in the order in which they are found
in the descriptor list.  Therefore, the descriptor list must contain the
ITDs in the correct order, i.e., a new ITD must be linked in after any
previous ITDs of the same endpoint.

This should fix garbled capture data in the USB audio drivers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-by: NColin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fix audio record functionality for some Full speed sound blaster devices.
Issue: Sometimes transaction complete indication is coming from HW one frame later.
Solution: If scan_periodic process now frame or previous frame now-1 and sitd transaction
is not finished yet, exit scan_periodic function and check the same transaction in the next frame.
Signed-off-by: NDimitry Epshtein <dima@marvell.com>
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Sometimes disable_periodic() stop scan_periodic before than free_cached_itd_list() was called.
In such case USB Host stacked during disconnect operation
Solution: add call of free_cached_itd_list() function in disable_periodic()
Signed-off-by: NDimitry Epshtein <dima@marvell.com>
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The EHCI specification says that an EHCI host controller may cache part of
the isochronous schedule.  The EHCI controller must advertise how much it
caches in the schedule through the HCCPARAMS register isochronous
scheduling threshold (IST) bits.

In theory, adding new iTDs within the IST should be harmless.  The HW will
follow the old cached linked list and miss the new iTD.  SW will notice HW
missed the iTD and return 0 for the transfer length.

However, Intel ICH9 chipsets (and some later chipsets) have issues when SW
attempts to schedule a split transaction within the IST.  All transfers
will cease being sent out that port, and the drivers will see isochronous
packets complete with a length of zero.  Start of frames may or may not
also disappear, causing the device to go into auto-suspend.  This "bus
stall" will continue until a control or bulk transfer is queued to a
device under that roothub.

Most drivers will never cause this behavior, because they use multiple
URBs with multiple packets to keep the bus busy.  If you limit the number
of URBs to one, you may be able to hit this bug.

Make sure the EHCI driver does not schedule full-speed transfers within
the IST under an Intel chipset.  Make sure that when we fall behind the
current microframe plus IST, we schedule the new transfer at the next
periodic interval after the IST.

Don't change the scheduling for new transfers, since the schedule slop will
always be greater than the IST.  Allow high speed isochronous transfers to
be scheduled within the IST, since this doesn't trigger the Intel chipset
bug.

Make sure that if the host caches the full frame, the EHCI driver's
internal isochronous threshold (ehci->i_thresh) is set to
8 microframes + 2 microframes wiggle room.  This is similar to what is done in
the case where the host caches less than the full frame.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Change the constant SCHEDULE_SLOP to be 80 microframes, instead of 10
frames.  It was always multiplied by 8 to convert frames to microframes.
SCHEDULE_SLOP is only used in ehci-sched.c.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the EHCI driver falls behind in its scheduling, the active stream's
first empty microframe may be in the past with respect to the current
microframe.  The code attempts to move the starting microframe ("start") N
number of microframes forward, where N is the interval of endpoint.
However, stream->interval is a copy of the endpoint's bInterval, which is
designated in frames for FS devices, and microframes for HS devices.
Convert stream->interval to microframes before using it to move the
starting microframe forward.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The EHCI driver does some bounds checking when it's scheduling an iTD for
an active endpoint.  It sets the local variable start to
stream->next_uframe and moves that variable further in the schedule if
necessary.  However, the driver fails to do anything with start before
jumping to the ready label and setting the URB's starting frame to
stream->next_uframe.  Alan Stern confirms the EHCI driver should set
stream->next_uframe to start before jumping.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1281) changes the way ehci-hcd deschedules interrupt
QHs, copying the approach used for async QHs.  The caller is no longer
responsible for rescheduling the QH if its queue is non-empty; instead
the reschedule is done directly by intr_deschedule(), after calling
qh_completions().  This is exactly the same as how end_unlink_async()
works.

ehci_urb_dequeue() and intr_deschedule() now correctly handle the case
where they are called while another interrupt URB for the same QH is
being given back.  This was a surprisingly large blind spot.  And
scan_periodic() now respects the new needs_rescan flag.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ehci_qh structure merged hw and sw together which is not good:
1. More and more items are being added into ehci_qh, the ehci_qh software
   part are unnecessary to be allocated in DMA qh_pool.
2. If HCD has local SRAM, the sw part will consume it too, and it won't
   bring any benefit.
3. For non-cache-coherence system, the entire ehci_qh is uncachable, actually
   we only need the hw part to be uncacheable. Spliting them will let the sw
   part to be cacheable.
Signed-off-by: NAlek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1274) simplifies the counting of transaction-error
retries.  Now we will count up from 0 to QH_XACTERR_MAX instead of
down from QH_XACTERR_MAX to 0.

The patch also fixes a small bug: qh->xacterr was not getting
initialized for interrupt endpoints.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NMatthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1259b) makes ehci-hcd return the total number of bytes
transferred in urb->actual_length for Isochronous transfers.
Until now, the actual_length value was unaccountably left at 0.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1243) tries to improve ehci-hcd's scheduling of
interrupt transfers.  Instead of trying to cram all transfers with the
same period into the same frame, the new code will spread the
transfers out among lots of different frames.  This should reduce the
periodic schedule load in any one frame -- some host controllers have
trouble when there's too much work to do.

A more thorough approach would stagger the uframe values as well.  But
this is enough to make a big improvement.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NDwayne Fontenot <dwayne.fontenot@att.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Without this patch, the driver won't check that the last fully-occupied
uframe for a new split transaction was vacant beforehand.  This can
lead to a situation in which the first 188 bytes of a 192-byte
isochronous transfer are scheduled in the same uframe as an existing
interrupt transfer.  The resulting schedule looks like this:

       uframe 0: 188-byte isoc-OUT SSPLIT, 8-byte int-IN SSPLIT
       uframe 1: 4-byte isoc-OUT SSPLIT

The SSPLITs are intermingled, causing an error in the downstream hub's
TT.

If you are having problems with devices or hub ports resetting, or failed
interrupt transfers, when you start using a USB audio or video (Isochronous)
device, this patch may help.
Signed-off-by: NDan Streetman <ddstreet@ieee.org>
Reported-by: NKung James <kong1191@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>

The base versions handle constant folding now.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ehci-hcd uses usb_get_urb() and usb_put_urb() in an unbalanced way causing
isochronous URB's kref.counts incrementing once per usb_submit_urb() call.
The culprit is *usb being set to NULL when usb_put_urb() is called after URB
is given back.
Due to other fixes there is no need for ehci-hcd to deal with usb_get_urb()
nor usb_put_urb() anymore, so patch removes their usages in ehci-hcd.
Patch also makes ehci_to_hcd(ehci)->self.bandwidth_allocated adjust, if a
stream finishes.
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state.  This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.

This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.

This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.

[ dbrownell@users.sourceforge.net: comment fixups ]
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Tested-by: NPhilippe Carriere <philippe-f.carriere@wanadoo.fr>
Tested-by: NFederico Briata <federicobriata@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1164) fixes a bug in the EHCI scheduler.  The interval
value it uses is already in linear format, not logarithmically coded.
The existing code can sometimes crash the system by trying to divide
by zero.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As noted by Stefan Neis <Stefan.Neis@kobil.com>, we had a recent
regression with EHCI periodic transfers, in some (seemingly not
all that common) cases.

The root cause was that the schedule activation was only loosely
coupled to the addition or removal of transfers, so two different
execution contexts could both think they had to deactivate (or
conversely activate) the schedule.  So this fix tightens that
coupling, managing it more like a refcount.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1098) changes the way ehci-hcd schedules its periodic
Iso transfers.  That the current scheduling code is wrong is clear on
the face of it: Sometimes it returns -EL2NSYNC (meaning that an URB
couldn't be scheduled because it was submitted too late), but it does
this even when the URB_ISO_ASAP flag is set (meaning the URB should be
scheduled as soon as possible).

The new code properly implements as-soon-as-possible scheduling,
assigning the next unexpired slot as the URB's starting point.  It
also is more careful about checking for Iso URB completion: It doesn't
bother to check for activity during frames that are already over,
and it allows for the possibility that some of the URB's packets may
have raced the hardware when they were submitted and so never got used
(the packet status is set to -EXDEV).

This fixes problems several people have experienced with USB video
applications.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove two (or one) conditional tests in per-urb isochronous
transfer setup code paths.
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Refactor the EHCI "if (handshake()) state = HC_STATE_HALT" idiom,
which appears 4 times, by replacing it with calls to a new function
called handshake_on_error_set_halt().  Saves a few bytes too.
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This has some bugfixes for the EHCI driver's ISO transfer scanning
logic.  It was leaving ITDs and SITDs on the schedule too long, for
a few different reasons, which caused trouble.

  (a)	Look at all microframes for high speed transfers, not just
	the ones we expect to have finished.  This way transfers
	ending mid-frame will complete without needing another IRQ.
	This also minimizes bogus scheduling underruns (e.g. EL2NSYNC).

  (b)	When we encounter an ISO transfer (either speed, but this
	hits mostly at full speed) that's not yet been completed,
	immediately stop scanning; we've caught up to the hardware,
	no matter what other indications might say.

  (c)	Always clean up ITDs (for high speed transfers) when the HC
	is no longer running.

I'm not sure whether the last one has been observed before, but both
the others have been reported with "real world" audio and video code.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Small updates to the EHCI driver's ISO support:

 - Get rid of the Kconfig option for full speed ISO.  It may
   not be perfect yet, but it hasn't appeared to be dangerous
   and pretty much every configuration wants it.

 - Instead of two places to disable an empty periodic schedule
   after an ISO transfer completes, just have one.

 - After the periodic schedule is disabled, we can short-circuit
   the schedule scan ... it can't possibly have more work to do.

Assuming a typical config with split iso enabled, the only change
in behavior should be almost unobservable:  quicker termination
of periodic scans when the schedule gets emptied.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the EHCI driver, itd->usecs[8] is used in periodic_usecs(), indexed by
uframe.  For an ITD's unused uframes it is 0, else it contains the same
value as itd->stream->usecs.  To check if an ITD's uframe is used, we can
instead test itd->hw_transaction[uframe]:  if used, it will be nonzero no
matter what endianess is used.

This patch replaces those two uses, eliminates itd->usecs[], and saves
eight bytes from each ITD.
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds a workaround for an issue reported with ISO transfers
on some EHCI controllers, most recently with VIA KT800 and PS3
EHCI silicon.

The issue is that the silicon doesn't necessarily seem to be done
using ISO DMA descriptors (itd, sitd) when it marks them inactive.
(One theory is that the ill-defined mechanism where hardware caches
periodic transfer descriptors isn't invalidating their state...)
With such silicon, quick re-use of those descriptors makes trouble.
Waiting until the next frame seems to be a sufficient workaround.

This patch ensures that the relevant descriptors aren't available
for immediate re-use.  It does so by not recycling them until after
issuing the completion callback which would reuse them by enqueueing
an URB and thus (re)allocating ISO DMA descriptors.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Cc: Masashi Kimoto <Masashi_Kimoto@hq.scei.sony.co.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>