Be more verbose on error messages and add one debug message.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Volker Ernst <volker.ernst@txtr.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

On i.MX21 SoCs, if the NFC_CONFIG1:NFC_INT_MASK bit is set,
NFC_CONFIG2:NFC_INT always reads out zero, even if an
operation is completed.  This patch uses enable_irq and
disable_irq_nosync instead of NFC_CONFIG1:NFC_INT_MASK to
mask NFC interrupts.  This allows NFC_CONFIG2:NFC_INT to also
be used to detect operation completion on i.MX21.

The i.MX21 NFC does not signal reset completion using
NFC_CONFIG1:NFC_INT_MASK, so instead reset completion is
tested by checking if NFC_CONFIG2 becomes 0.
Signed-off-by: NIvo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch allows the mxc_nand driver to reset the NAND
flash controller.  NFC registers are (re-)set after
completion of the reset, as a reset will have reverted
the NFC registers to their default values.
Signed-off-by: NIvo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds support for SoC build-in RTC device on litekit board.
Signed-off-by: NVladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds support for build-in RTC device found on
Freescale imx31 and imx35 SoCs.
Signed-off-by: NVladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Hibernate: user.c, fix SNAPSHOT_SET_SWAP_AREA handling

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFSv4: fix delegated locking
  NFS: Ensure that the WRITE and COMMIT RPC calls are always uninterruptible
  NFS: Fix a race with the new commit code
  NFS: Ensure that writeback_single_inode() calls write_inode() when syncing
  NFS: Fix the mode calculation in nfs_find_open_context
  NFSv4: Fall back to ordinary lookup if nfs4_atomic_open() returns EISDIR

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Add some more commentary to __raw_local_irq_save()
  sparc64: Fix memory leak in pci_register_iommu_region().
  sparc64: Add kmemleak annotation to sun4v_build_virq()
  sparc64: Support kmemleak.
  sparc64: Add function graph tracer support.
  sparc64: Give a stack frame to the ftrace call sites.
  sparc64: Use a seperate counter for timer interrupts and NMI checks, like x86.
  sparc64: Remove profiling from some low-level bits.
  sparc64: Kill unnecessary static on local var in ftrace_call_replace().
  sparc64: Kill CONFIG_STACK_DEBUG code.
  sparc64: Add HAVE_FUNCTION_TRACE_MCOUNT_TEST and tidy up.
  sparc64: Adjust __raw_local_irq_save() to cooperate in NMIs.
  sparc64: Use kstack_valid() in die_if_kernel().

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (25 commits)
  smc91c92_cs: define multicast_table as unsigned char
  can: avoids a false warning
  e1000e: stop cleaning when we reach tx_ring->next_to_use
  igb: restrict WoL for 82576 ET2 Quad Port Server Adapter
  virtio_net: missing sg_init_table
  Revert "tcp: Set CHECKSUM_UNNECESSARY in tcp_init_nondata_skb"
  iwlwifi: need check for valid qos packet before free
  tcp: Set CHECKSUM_UNNECESSARY in tcp_init_nondata_skb
  udp: fix for unicast RX path optimization
  myri10ge: fix rx_pause in myri10ge_set_pauseparam
  net: corrected documentation for hardware time stamping
  stmmac: use resource_size()
  x.25 attempts to negotiate invalid throughput
  x25: Patch to fix bug 15678 - x25 accesses fields beyond end of packet.
  bridge: Fix IGMP3 report parsing
  cnic: Fix crash during bnx2x MTU change.
  qlcnic: fix set mac addr
  r6040: fix r6040_multicast_list
  vhost-net: fix vq_memory_access_ok error checking
  ath9k: fix double calls to ath_radio_enable
  ...

smc91c92_cs:
  * define multicast_table as unsigned char
  * remove unnecessary "#ifndef final_version"
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At this point optlen == sizeof(sfilter) but some compilers are dumb.

Reported-by: Németh Márton <nm127@freemail.h
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NOliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx ring buffers after tx_ring->next_to_use are volatile and could
change, possibly causing a crash.  Stop cleaning when we hit
tx_ring->next_to_use.
Signed-off-by: NTerry Loftin <terry.loftin@hp.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restrict Wake-on-LAN to first port on 82576 ET2 quad port NICs, as it is
only supported there.
Signed-off-by: NStefan Assmann <sassmann@redhat.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suggested by Peter Zijlstra
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	lib/Kconfig.debug

Found by kmemleak.

If request_resource() fails, we leak the struct resource we
allocated to represent the IOMMU mapping area.

This actually happens on sun4v machines because the IOMEM area is only
reported sans the IOMMU region, unlike all previous systems.  I'll
need to fix that at some point, but for now fix the leak.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only reference we store to this memory is in the form of a
physical address, so kmemleak can't see it.

Add a kmemleak_not_leak() annotation.

It's probably useful to be able to look at a dump of these things
either via debugfs or similar, and thus we could at some point store
them in some kind of table and therefore get rid of this annotation.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only missing thing was an _sdata marker in vmlinux.lds.S
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's the only way we'll be able to implement the function
graph tracer properly.

A positive is that we no longer have to worry about the
linker over-optimizing the tail call, since we don't
use a tail call any more.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This keeps us from having to use kstat_irqs_cpu() from the NMI handler,
the former of which is a profiled function.

Instead we use a currently empty slot in the cpu_data
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These include the timer implementation, perf events support, and the
performance counter register (pcr) programming layer.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic stack tracer does this job just as well.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check function_trace_stop at ftrace_caller

Toss mcount_call and dummy call of ftrace_stub, unnecessary.

Document problems we'll have if the final kernel image link
ever turns on relaxation.

Properly size 'ftrace_call' so it looks right when inspecting
instructions under gdb et al.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we are in an NMI then doing a plain raw_local_irq_disable() will
write PIL_NORMAL_MAX into %pil, which is lower than PIL_NMI, and thus
we'll re-enable NMIs and recurse.

Doing a simple:

	%pil = %pil | PIL_NORMAL_MAX

does what we want, if we're already at PIL_NMI (15) we leave it at
that setting, else we set it to PIL_NORMAL_MAX (14).

This should get the function tracer working on sparc64.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This gets rid of a local function (is_kernel_stack()) which tries to
do the same thing, yet poorly in that it doesn't handle IRQ stacks
properly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing sg_init_table for sg_set_buf in virtio_net which
induced in defer skb patch.
Reported-by: NThomas Müller <thomas@mathtm.de>
Tested-by: NThomas Müller <thomas@mathtm.de>
Signed-off-by: NShirley Ma <xma@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* anonvma:
  anonvma: when setting up page->mapping, we need to pick the _oldest_ anonvma
  anon_vma: clone the anon_vma chain in the right order
  vma_adjust: fix the copying of anon_vma chains
  Simplify and comment on anon_vma re-use for anon_vma_prepare()

* master.kernel.org:/home/rmk/linux-2.6-arm: (21 commits)
  ARM: Fix ioremap_cached()/ioremap_wc() for SMP platforms
  ARM: 6043/1: AT91 slow-clock resume: Don't wait for a disabled PLL to lock
  ARM: 6031/1: fix Thumb-2 decompressor
  ARM: 6029/1: ep93xx: gpio.c: local functions should be static
  ARM: 6028/1: ARM: add MAINTAINERS for U300
  ARM: 6024/1: bcmring: fix missing down on semaphore in dma.c
  MXC: mach_armadillo5x0: Add USB Host support.
  ARM mach-mx3: duplicated include
  ARM mach-mx3: duplicated include
  imx31: add watchdog device on litekit board.
  imx3: Add watchdog platform device support
  MXC: mach-mx31_3ds: add support for freescale mc13783 power management device.
  MXC: mach-mx31_3ds: Add SPI1 device support.
  MXC: mach-mx31_3ds: Add support for on board NAND Flash.
  MXC: mach-mx31_3ds: Update variable names over recent mach name modification.
  imx31: fix parent clock for rtc
  i.MX51: remove NFC AXI static mapping
  i.MX51: determine silicon revision dynamically
  i.MX51: map TZIC dynamically
  i.MX51: Use correct clock for gpt
  ...

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: make sure the chunk allocator doesn't create zero length chunks
  Btrfs: fix data enospc check overflow

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  quota: Fix possible dq_flags corruption
  quota: Hide warnings about writes to the filesystem before quota was turned on
  ext3: symlink must be handled via filesystem specific operation
  ext2: symlink must be handled via filesystem specific operation

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
  udf: add speciffic ->setattr callback
  udf: potential integer overflow

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (36 commits)
  MIPS: Calculate proper ebase value for 64-bit kernels
  MIPS: Alchemy: DB1200: Remove custom wait implementation
  MIPS: Big Sur: Make defconfig more useful.
  MIPS: Fix __vmalloc() etc. on MIPS for non-GPL modules
  MIPS: Sibyte: Fix M3 TLB exception handler workaround.
  MIPS: BCM63xx: Fix build failure in board_bcm963xx.c
  MIPS: uasm: Add OR instruction.
  MIPS: Sibyte: Apply M3 workaround only on affected chip types and versions.
  MIPS: BCM63xx: Initialize gpio_out_low & out_high to current value at boot.
  MIPS: BCM63xx: Register SSB SPROM fallback in board's first stage callback
  MIPS: BCM63xx: Fix typo in cpu-feature-overrides file.
  MIPS: BCM63xx: Add support for second uart.
  MIPS: BCM63xx: Fix double gpio registration.
  MIPS: BCM63xx: Add DWVS0 board
  MIPS: BCM63xx: Add the RTA1025W-16 BCM6348-based board to suppported boards.
  MIPS: BCM63xx: Fix BCM6338 and BCM6345 gpio count
  MIPS: libgcc.h: Checkpatch cleanup
  MIPS: Loongson-2F: Flush the branch target history in BTB and RAS
  MIPS: Move signal trampolines off of the stack.
  MIPS: Preliminary VDSO
  ...

* 'for-2.6.34' of git://linux-nfs.org/~bfields/linux:
  svcrdma: RDMA support not yet compatible with RPC6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix typo "numer" -> "number" in alloc.c
  nilfs2: Remove an uninitialization warning in nilfs_btree_propagate_v()
  nilfs2: fix a wrong type conversion in nilfs_ioctl()

Otherwise we might be mapping in a page in a new mapping, but that page
(through the swapcache) would later be mapped into an old mapping too.
The page->mapping must be the case that works for everybody, not just
the mapping that happened to page it in first.

Here's the scenario:

 - page gets allocated/mapped by process A. Let's call the anon_vma we
   associate the page with 'A' to keep it easy to track.

 - Process A forks, creating process B. The anon_vma in B is 'B', and has
   a chain that looks like 'B' -> 'A'. Everything is fine.

 - Swapping happens. The page (with mapping pointing to 'A') gets swapped
   out (perhaps not to disk - it's enough to assume that it's just not
   mapped any more, and lives entirely in the swap-cache)

 - Process B pages it in, which goes like this:

        do_swap_page ->
          page = lookup_swap_cache(entry);
         ...
          set_pte_at(mm, address, page_table, pte);
          page_add_anon_rmap(page, vma, address);

   And think about what happens here!

   In particular, what happens is that this will now be the "first"
   mapping of that page, so page_add_anon_rmap() used to do

        if (first)
                __page_set_anon_rmap(page, vma, address);

   and notice what anon_vma it will use? It will use the anon_vma for
   process B!

   What happens then? Trivial: process 'A' also pages it in (nothing
   happens, it's not the first mapping), and then process 'B' execve's
   or exits or unmaps, making anon_vma B go away.

   End result: process A has a page that points to anon_vma B, but
   anon_vma B does not exist any more.  This can go on forever.  Forget
   about RCU grace periods, forget about locking, forget anything like
   that.  The bug is simply that page->mapping points to an anon_vma
   that was correct at one point, but was _not_ the one that was shared
   by all users of that possible mapping.

Changing it to always use the deepest anon_vma in the anonvma chain gets
us to the safest model.

This can be improved in certain cases: if we know the page is private to
just this particular mapping (for example, it's a new page, or it is the
only swapcache entry), we could pick the top (most specific) anon_vma.

But that's a future optimization. Make it _work_ reliably first.
Reviewed-by: NRik van Riel <riel@redhat.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Tested-by: Borislav Petkov <bp@alien8.de> [ "What do you know, I think you fixed it!" ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We want to walk the chain in reverse order when cloning it, so that the
order of the result chain will be the same as the order in the source
chain.  When we add entries to the chain, they go at the head of the
chain, so we want to add the source head last.
Reviewed-by: NRik van Riel <riel@redhat.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Tested-by: Borislav Petkov <bp@alien8.de> [ "No, it still oopses" ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>