For chips requiring RTC reset, TSF has to be restored
after power on reset.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Disable L1 state ONLY when device is in D3 mode.
* Clear bit 22 of register 0x4004.
* Handle power on/off properly

Not setting the workarounds properly resulted in the
disappearance of the card in certain cases.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The default noise floor was never initialized for
AR9287.This patch helps in reporting the correct
RSSI for this version of chipset.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LP (and probably N) PHY has the same radio disabled bit as
the higher-revision A and G PHYs.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SDIO works (more or less), so remove the BROKEN dependency and
let people test it.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the following build error when CONFIG_B43_LEDS is not selected:

drivers/net/wireless/b43/main.c: In function 'b43_remove':
drivers/net/wireless/b43/main.c:4990: error: 'struct b43_leds' has no member named 'stop'
drivers/net/wireless/b43/main.c:4991: error: 'struct b43_leds' has no member named 'work'
make[4]: *** [drivers/net/wireless/b43/main.o] Error 1
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't abuse wl->current_dev in the LED work for checking whether we're
going down. Add an explicit variable.
This fixes a crash on rmmod dereferencing the wl->current_dev NULL pointer
in various other places of the driver.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current verison of b43 uses "b43_phyop_switch_analog_generic" for A,
G and LP phys.

According to the spec, this is the wrong behaviour for the LP PHY
(see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore )

While no problems on the x86 plattform where seen, this leads to a crash
on the BCM5354 SoC (MIPS 32 LE plattform).
This patch implements the analog switch for LP PHYs according to the
specs. It fixes the crash
signed-off-by: NThomas Ilnseher <illth@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reduces IRQ pressure by about one third on a saturated link
by disabling the PMQ mechanism. We currently don't use that mechanism.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for verbose runtime statistics.
It defaults to off and must be enabled in debugfs, if desired.
The first measurement may be incorrect, because statistics are not cleared
after they got enabled through debugfs.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

synchronize_irq is meaningless for SDIO. sdio_release_irq will
sync the IRQ thread for us.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to release the SDIO host before locking the driver mutex.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't need to call the irqsafe callbacks.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for Soft-MAC SDIO devices to b43.
The driver still lacks some fixes for SDIO devices, so it's currently
marked as BROKEN.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes most of the b43 suspend/resume code (it's handled by mac80211)
and moves the registration of devices to the attachment phase. This is
required, because we must not register/unregister devices on suspend/resume.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a check saying
	/* we're good if we have both BSSID and channel */
	if (wdev->conn->params.bssid && wdev->conn->params.channel) {

but that isn't true -- we need the BSS struct. This leads
to errors such as

    Trying to associate with 00:1b:53:11:dc:40 (SSID='TEST' freq=2412 MHz)
    ioctl[SIOCSIWFREQ]: No such file or directory
    ioctl[SIOCSIWESSID]: No such file or directory
    Association request to the driver failed
    Associated with 00:1b:53:11:dc:40

in wpa_supplicant, as reported by Holger.

Instead, we really need to have the BSS struct, and if we
don't, then we need to initiate a scan for it. But we may
already have the BSS struct here, so hang on to it if we
do and scan if we don't.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The contention window is supposed to be a power of two minus one, i.e.
15, 31, 63, 127...  minstrel_rate_init() forgets to subtract 1, so the
sequence becomes 15, 32, 66, 134...

Bug reported by Dan Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix printk format warnings:

drivers/ssb/sdio.c:336: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
drivers/ssb/sdio.c:443: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a new usbid for Zcomax XG-705A to the device table.

Cc: stable@kernel.org
Reported-by: NJari Jaakola <jari.jaakola@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an SPROM revision is not recognized, the code falls back to a V1
SPROM; however, that revision is not forced in the appropriate structure.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.

Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can not assume antenna "A" is the first valid anttena for
all the NIC. Need to make sure choice the correct antenna based on
h/w configuration for transmit to avoid sending frame on invalid
antenna
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.

Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: NRick Farrington <rickdic@hotmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we cleaned up the driver to properly tell mac80211 about HT rates
("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke
internal rate indexing in 2.4 GHz band.
Signed-off-by: NDaniel C Halperin <daniel.c.halperin@intel.com>
Tested-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a resume failure where a signal is pending on resume
so the firmware upload fails.
This removes the interruptible sleep, because we don't really need it.
In the worst case (with broken firmware) the sleep loop will take 1 second.
In the common case (working firmware), it will only take a few milliseconds.
So we don't really need to be interruptible.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disable SDIO coreswitch debugging.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When this was added no defaults were set and it seems
this implies n. Default this to y.
Reported-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WEXT's "struct iw_freq" can also be used to handle a channel. This patch now
uses cfg80211_wext_freq() instead of hand-converting the frequency. That
allows user-space to specify channels as well, like with SIOCSIWFREQ.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Force wake the mac80211 queues on init.
Under rare circumstances they may be stopped, if a DMA error or
something else causes a device reset while a queue was stopped.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As the hostap driver was converted to use net_device_ops, a mistake was
made in hostap_main.c (commit 5ae4efbc).
Originally, the tx_queue_len was set to 0 for every other interface than
HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to
0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous
behavior makes the driver to drop all packets in AP mode.

Change the way 0 is assigned to tx_queue_len according to the original
logic.
Signed-off-by: NMartin Decky <martin@decky.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* 'osync_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  fsync: wait for data writeout completion before calling ->fsync
  vfs: Remove generic_osync_inode() and sync_page_range{_nolock}()
  fat: Opencode sync_page_range_nolock()
  pohmelfs: Use new syncing helper
  xfs: Convert sync_page_range() to simple filemap_write_and_wait_range()
  ocfs2: Update syncing after splicing to match generic version
  ntfs: Use new syncing helpers and update comments
  ext4: Remove syncing logic from ext4_file_write
  ext3: Remove syncing logic from ext3_file_write
  ext2: Update comment about generic_osync_inode
  vfs: Introduce new helpers for syncing after writing to O_SYNC file or IS_SYNC inode
  vfs: Rename generic_file_aio_write_nolock
  ocfs2: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
  pohmelfs: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
  vfs: Remove syncing from generic_file_direct_write() and generic_file_buffered_write()
  vfs: Export __generic_file_aio_write() and add some comments
  vfs: Introduce filemap_fdatawait_range

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw:
  GFS2: Whitespace fixes
  GFS2: Remove unused sysfs file
  GFS2: Be extra careful about deallocating inodes
  GFS2: Remove no_formal_ino generating code
  GFS2: Rename eattr.[ch] as xattr.[ch]
  GFS2: Clean up of extended attribute support
  GFS2: Add explanation of extended attr on-disk format
  GFS2: Add "-o errors=panic|withdraw" mount options
  GFS2: jumping to wrong label?
  GFS2: free disk inode which is deleted by remote node -V2
  GFS2: Add a document explaining GFS2's uevents
  GFS2: Add sysfs link to device
  GFS2: Replace assertion with proper error handling
  GFS2: Improve error handling in inode allocation
  GFS2: Add some more info to uevents
  GFS2: Add online uevent to GFS2

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
  udf: Fix possible corruption when close races with write
  udf: Perform preallocation only for regular files
  udf: Remove wrong assignment in udf_symlink
  udf: Remove dead code

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (21 commits)
  fs/Kconfig: move nilfs2 outside misc filesystems
  nilfs2: convert nilfs_bmap_lookup to an inline function
  nilfs2: allow btree code to directly call dat operations
  nilfs2: add update functions of virtual block address to dat
  nilfs2: remove individual gfp constants for each metadata file
  nilfs2: stop zero-fill of btree path just before free it
  nilfs2: remove unused btree argument from btree functions
  nilfs2: remove nilfs_dat_abort_start and nilfs_dat_abort_free
  nilfs2: shorten freeze period due to GC in write operation v3
  nilfs2: add more check routines in mount process
  nilfs2: An unassigned variable is assigned to a never used structure member
  nilfs2: use GFP_NOIO for bio_alloc instead of GFP_NOWAIT
  nilfs2: stop using periodic write_super callback
  nilfs2: clean up nilfs_write_super
  nilfs2: fix disorder of nilfs_write_super in nilfs_sync_fs
  nilfs2: remove redundant super block commit
  nilfs2: implement nilfs_show_options to display mount options in /proc/mounts
  nilfs2: always lookup disk block address before reading metadata block
  nilfs2: use semaphore to protect pointer to a writable FS-instance
  nilfs2: fix format string compile warning (ino_t)
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: consolidate reconnect logic in smb_init routines
  cifs: Replace wrtPending with a real reference count
  cifs: protect GlobalOplock_Q with its own spinlock
  cifs: use tcon pointer in cifs_show_options
  cifs: send IPv6 addr in upcall with colon delimiters
  [CIFS] Fix checkpatch warnings
  PATCH] cifs: fix broken mounts when a SSH tunnel is used (try #4)
  [CIFS] Memory leak in ntlmv2 hash calculation
  [CIFS] potential NULL dereference in parse_DFS_referrals()

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (21 commits)
  sparc64: Initial niagara2 perf counter support.
  sparc64: Perf counter 'nop' event is not constant.
  sparc64: Provide a way to specify a perf counter overflow IRQ enable bit.
  sparc64: Provide hypervisor tracing bit support for perf counters.
  sparc64: Initial hw perf counter support.
  sparc64: Implement a real set_perf_counter_pending().
  sparc64: Use nmi_enter() and nmi_exit(), as needed.
  sparc64: Provide extern decls for sparc_??u_type strings.
  sparc64: Make touch_nmi_watchdog() actually work.
  sparc64: Kill unnecessary cast in profile_timer_exceptions_notify().
  sparc64: Manage NMI watchdog enabling like x86.
  sparc: add basic support for 'perf'
  sparc: convert /proc/io_map, /proc/dvma_map to seq_file
  sparc, leon: sparc-leon specific SRMMU initialization and bootup fixes.
  sparc,leon: Added support for AMBAPP bus.
  sparc,leon: Introduce the sparc-leon CPU type.
  sparc,leon: Redefine MMU register access asi if CONFIG_LEON
  sparc,leon: CONFIG_SPARC_LEON option and leon specific files.
  sparc64: cheaper asm/uaccess.h inclusion
  SPARC: fix duplicate declaration
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
  netxen: update copyright
  netxen: fix tx timeout recovery
  netxen: fix file firmware leak
  netxen: improve pci memory access
  netxen: change firmware write size
  tg3: Fix return ring size breakage
  netxen: build fix for INET=n
  cdc-phonet: autoconfigure Phonet address
  Phonet: back-end for autoconfigured addresses
  Phonet: fix netlink address dump error handling
  ipv6: Add IFA_F_DADFAILED flag
  net: Add DEVTYPE support for Ethernet based devices
  mv643xx_eth.c: remove unused txq_set_wrr()
  ucc_geth: Fix hangs after switching from full to half duplex
  ucc_geth: Rearrange some code to avoid forward declarations
  phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
  drivers/net/phy: introduce missing kfree
  drivers/net/wan: introduce missing kfree
  net: force bridge module(s) to be GPL
  Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
  ...

Fixed up trivial conflicts:

 - arch/x86/include/asm/socket.h

   converted to <asm-generic/socket.h> in the x86 tree.  The generic
   header has the same new #define's, so that works out fine.

 - drivers/net/tun.c

   fix conflict between 89f56d1e ("tun: reuse struct sock fields") that
   switched over to using 'tun->socket.sk' instead of the redundantly
   available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
   to the TUN driver") which added a new 'tun->sk' use.

   Noted in 'next' by Stephen Rothwell.

* 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: split __phys_addr out into separate file
  xen: use stronger barrier after unlocking lock
  xen: only enable interrupts while actually blocking for spinlock
  xen: make -fstack-protector work under Xen