[ Upstream commit 7af3f558aca74f2ee47b173f1c27f6bb9a5b5561 ]

Realtek RTL8822BE BT chip on ASUS X420FA cannot be turned on correctly
after on-off several times. Bluetooth daemon sets BT mode failed when
this issue happens. Scanning must be active while turning off for this
bug to be hit.

bluetoothd[1576]: Failed to set mode: Failed (0x03)

If BT is turned off, then turned on again, it works correctly again.

According to the vendor driver, the HCI_QUIRK_RESET_ON_CLOSE flag is set
during probing. So, this patch makes Realtek's BT reset on close to fix
this issue.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=203429Signed-off-by: NJian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

commit 1ffdb51f28e8ec6be0a2b812c1765b5cf5c44a8f upstream.

This reverts commit a0085f25.

This commit has caused regressions in notebooks that support suspend
to idle such as the XPS 9360, XPS 9370 and XPS 9380.

These notebooks will wakeup from suspend to idle from an unsolicited
advertising packet from an unpaired BLE device.

In a bug report it was sugggested that this is caused by a generic
lack of LE privacy support.  Revert this commit until that behavior
can be avoided by the kernel.

Fixes: a0085f25 ("Bluetooth: btusb: driver to enable the usb-wakeup feature")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=200039
Link: https://marc.info/?l=linux-bluetooth&m=156441081612627&w=2
Link: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/750073/
CC: Bastien Nocera <hadess@hadess.net>
CC: Christian Kellner <ckellner@redhat.com>
CC: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: NMario Limonciello <mario.limonciello@dell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8059ba0bd0e4694e51c2ee6438a77b325f06c0d5 ]

On WCN3990 downloading the NVM sometimes fails with a "TLV response
size mismatch" error:

[  174.949955] Bluetooth: btqca.c:qca_download_firmware() hci0: QCA Downloading qca/crnv21.bin
[  174.958718] Bluetooth: btqca.c:qca_tlv_send_segment() hci0: QCA TLV response size mismatch

It seems the controller needs a short time after downloading the
firmware before it is ready for the NVM. A delay as short as 1 ms
seems sufficient, make it 10 ms just in case. No event is received
during the delay, hence we don't just silently drop an extra event.
Signed-off-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

commit b36a1552d7319bbfd5cf7f08726c23c5c66d4f73 upstream.

Certain ttys operations (pty_unix98_ops) lack tiocmget() and tiocmset()
functions which are called by the certain HCI UART protocols (hci_ath,
hci_bcm, hci_intel, hci_mrvl, hci_qca) via hci_uart_set_flow_control()
or directly. This leads to an execution at NULL and can be triggered by
an unprivileged user. Fix this by adding a helper function and a check
for the missing tty operations in the protocols code.

This fixes CVE-2019-10207. The Fixes: lines list commits where calls to
tiocm[gs]et() or hci_uart_set_flow_control() were added to the HCI UART
protocols.

Link: https://syzkaller.appspot.com/bug?id=1b42faa2848963564a5b1b7f8c837ea7b55ffa50
Reported-by: syzbot+79337b501d6aa974d0f6@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # v2.6.36+
Fixes: b3190df6 ("Bluetooth: Support for Atheros AR300x serial chip")
Fixes: 118612fb ("Bluetooth: hci_bcm: Add suspend/resume PM functions")
Fixes: ff289559 ("Bluetooth: hci_intel: Add Intel baudrate configuration support")
Fixes: 162f812f ("Bluetooth: hci_uart: Add Marvell support")
Fixes: fa9ad876 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Signed-off-by: NVladis Dronov <vdronov@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Reviewed-by: NYu-Chen, Cho <acho@suse.com>
Tested-by: NYu-Chen, Cho <acho@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 881cec4f6b4da78e54b73c046a60f39315964c7d ]

Without the QCA ROME setup routine this adapter fails to establish a SCO
connection.

T:  Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3501 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 44d34af2e4cfd0c5357182f8b43f3e0a1fe30a2e ]

Without the QCA ROME setup routine this adapter fails to establish a SCO
connection.

T:  Bus=01 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3491 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4ce9146e0370fcd573f0372d9b4e5a211112567c ]

Syzkaller found that it is possible to provoke a memory leak by
never freeing rx_skb in struct bcsp_struct.

Fix by freeing in bcsp_close()
Signed-off-by: NTomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+98162c885993b72f19c4@syzkaller.appspotmail.com
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7f09d5a6c33be66a5ca19bf9dd1c2d90c5dfcf0d ]

This patch enables enough time to ROME controller to bootup
after we bring the enable pin out of reset.

Fixes: 05ba533c ("Bluetooth: hci_qca: Add serdev support").
Signed-off-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: NRocky Liao <rjliao@codeaurora.org>
Tested-by: NRocky Liao <rjliao@codeaurora.org>
Tested-by: NClaire Chang <tientzu@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

commit 77f328dbc6cf42f22c691a164958a5452142a542 upstream.

Restore bdev->tx_state with clearing bit BTMTKUART_TX_WAIT_VND_EVT
when there is an error on waiting for the corresponding event.

Fixes: 7237c4c9 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 771acc7e4a6e5dba779cb1a7fd851a164bc81033 upstream.

Badly-designed systems might have (for example) active-high wake pins
that default to high (e.g., because of external pull ups) until they
have an active firmware which starts driving it low.  This can cause an
interrupt storm in the time between request_irq() and disable_irq().

We don't support shared interrupts here, so let's just pre-configure the
interrupt to avoid auto-enabling it.

Fixes: fd913ef7 ("Bluetooth: btusb: Add out-of-band wakeup support")
Fixes: 5364a0b4f4be ("arm64: dts: rockchip: move QCA6174A wakeup pin into its USB node")
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Reviewed-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 56897b217a1d0a91c9920cb418d6b3fe922f590a upstream.

task A:                                task B:
hci_uart_set_proto                     flush_to_ldisc
 - p->open(hu) -> h5_open  //alloc h5  - receive_buf
 - set_bit HCI_UART_PROTO_READY         - tty_port_default_receive_buf
 - hci_uart_register_dev                 - tty_ldisc_receive_buf
                                          - hci_uart_tty_receive
				           - test_bit HCI_UART_PROTO_READY
				            - h5_recv
 - clear_bit HCI_UART_PROTO_READY             while() {
 - p->open(hu) -> h5_close //free h5
				              - h5_rx_3wire_hdr
				               - h5_reset()  //use-after-free
                                              }

It could use ioctl to set hci uart proto, but there is
a use-after-free issue when hci_uart_register_dev() fail in
hci_uart_set_proto(), see stack above, fix this by setting
HCI_UART_PROTO_READY bit only when hci_uart_register_dev()
return success.

Reported-by: syzbot+899a33dc0fa0dbaf06a6@syzkaller.appspotmail.com
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: NJeremy Cline <jcline@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 32a7b4cbe93b0a0ef7e63d31ca69ce54736c4412 upstream.

The hci_dev struct hdev is referenced in work queues and timers started
by open() in some protocols. This creates a race between the
initialization function and the work or timer which can result hdev
being dereferenced while it is still null.

The syzbot report contains a reliable reproducer which causes a null
pointer dereference of hdev in hci_uart_write_work() by making the
memory allocation for hdev fail.

To fix this, ensure hdev is valid from before calling a protocol's
open() until after calling a protocol's close().

Reported-by: syzbot+257790c15bcdef6fe00c@syzkaller.appspotmail.com
Signed-off-by: NJeremy Cline <jcline@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1dc2d785156cbdc80806c32e8d2c7c735d0b4721 upstream.

h4_recv_buf() callers store the return value to socket buffer and
recursively pass the buffer to h4_recv_buf() without protection. So,
ERR_PTR returned from h4_recv_buf() can be dereferenced, if called again
before setting the socket buffer to NULL from previous error. Check if
skb is ERR_PTR in h4_recv_buf().

Reported-by: syzbot+017a32f149406df32703@syzkaller.appspotmail.com
Signed-off-by: NMyungho Jung <mhjungk@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 00df214b1faae520880cc5c57e206f21239ef741 upstream.

Realtek bluetooth may not work after reboot:
[   12.446130] Bluetooth: hci0: RTL: rtl: unknown IC info, lmp subver a99e, hci rev 826c, hci ver 0008

This is a regression introduced by commit 26503ad2 ("Bluetooth:
btrtl: split the device initialization into smaller parts"). The new
logic errors out early when no matching IC info can be found, in this
case it means the firmware is already loaded.

So let's assume the firmware is already loaded when we can't find
matching IC info, like the old logic did.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201921
Fixes: 26503ad2 ("Bluetooth: btrtl: split the device initialization into smaller parts")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 28ac03b9ac3f784c2f048a910c8d0a7a87483b66 ]

On some systems that actually have the bluetooth controller wired up
with an extra clock signal, it's possible the bluetooth controller
probes before the clock provider. clk_get would return a defer probe
error, which was not handled by this driver.

Handle this properly, so that these systems can work reliably.
Tested-by: NOndrej Jirman <megous@megous.com>
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2da711bcebe81209a9f2f90e145600eb1bae2b71 ]

Include the new USB product ID for Intel Bluetooth device 22260
family(CcPeak)

The /sys/kernel/debug/usb/devices portion for this device is:

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0029 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
Signed-off-by: NRaghuram Hegde <raghuram.hegde@intel.com>
Signed-off-by: NChethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c2d78273 ]

When flag KASAN is set, we are seeing an following crash while removing
hci_uart module.

[   50.589909] Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b73
[   50.597902] Mem abort info:
[   50.600846]   Exception class = DABT (current EL), IL = 32 bits
[   50.606959]   SET = 0, FnV = 0
[   50.610142]   EA = 0, S1PTW = 0
[   50.613396] Data abort info:
[   50.616401]   ISV = 0, ISS = 0x00000004
[   50.620373]   CM = 0, WnR = 0
[   50.623466] [006b6b6b6b6b6b73] address between user and kernel address ranges
[   50.630818] Internal error: Oops: 96000004 [#1] PREEMPT SMP

[   50.671670] PC is at qca_power_shutdown+0x28/0x100 [hci_uart]
[   50.677593] LR is at qca_close+0x74/0xb0 [hci_uart]
[   50.775689] Process rmmod (pid: 2144, stack limit = 0xffffff801ba90000)
[   50.782493] Call trace:

[   50.872150] [<ffffff8000c3c81c>] qca_power_shutdown+0x28/0x100 [hci_uart]
[   50.879138] [<ffffff8000c3c968>] qca_close+0x74/0xb0 [hci_uart]
[   50.885238] [<ffffff8000c3a71c>] hci_uart_unregister_device+0x44/0x50 [hci_uart]
[   50.892846] [<ffffff8000c3c9f4>] qca_serdev_remove+0x50/0x5c [hci_uart]
[   50.899654] [<ffffff800844f630>] serdev_drv_remove+0x28/0x38
[   50.905489] [<ffffff800850fc44>] device_release_driver_internal+0x140/0x1e4
[   50.912653] [<ffffff800850fd94>] driver_detach+0x78/0x84
[   50.918121] [<ffffff800850edac>] bus_remove_driver+0x80/0xa8
[   50.923942] [<ffffff80085107dc>] driver_unregister+0x4c/0x58
[   50.929768] [<ffffff8000c3ca8c>] qca_deinit+0x24/0x598 [hci_uart]
[   50.936045] [<ffffff8000c3ca10>] hci_uart_exit+0x10/0x48 [hci_uart]
[   50.942495] [<ffffff8008136630>] SyS_delete_module+0x17c/0x224

This crash is due to dereference of hdev, after freeing it.
Signed-off-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a357ea09 ]

This patch adds the device ID for the AMPAK AP6335 combo module used
in the 1st generation WeTek Hub Android/LibreELEC HTPC box. The WiFI
chip identifies itself as BCM4339, while Bluetooth identifies itself
as BCM4335 (rev C0):

```
[    4.864248] Bluetooth: hci0: BCM: chip id 86
[    4.866388] Bluetooth: hci0: BCM: features 0x2f
[    4.889317] Bluetooth: hci0: BCM4335C0
[    4.889332] Bluetooth: hci0: BCM4335C0 (003.001.009) build 0000
[    9.778383] Bluetooth: hci0: BCM4335C0 (003.001.009) build 0268
```

Output from hciconfig:

```
hci0:	Type: Primary  Bus: UART
	BD Address: 43:39:00:00:1F:AC  ACL MTU: 1021:8  SCO MTU: 64:1
	UP RUNNING
	RX bytes:7567 acl:234 sco:0 events:386 errors:0
	TX bytes:53844 acl:77 sco:0 commands:304 errors:0
	Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
	Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
	Link policy: RSWITCH SNIFF
	Link mode: SLAVE ACCEPT
	Name: 'HUB'
	Class: 0x0c0000
	Service Classes: Rendering, Capturing
	Device Class: Miscellaneous,
	HCI Version: 4.0 (0x6)  Revision: 0x10c
	LMP Version: 4.0 (0x6)  Subversion: 0x6109
	Manufacturer: Broadcom Corporation (15)
```
Signed-off-by: NChristian Hewitt <christianshewitt@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:

	kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
	kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
	devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: NKees Cook <keescook@chromium.org>

The percpu_rw_semaphore is not currently freed, and this leads to
a crash when the stale rcu callback is invoked.  DEBUG_OBJECTS
detects this.

 ODEBUG: free active (active state 1) object type: rcu_head hint: (null)
 ------------[ cut here ]------------
 WARNING: CPU: 1 PID: 2024 at debug_print_object+0xac/0xc8
 PC is at debug_print_object+0xac/0xc8
 LR is at debug_print_object+0xac/0xc8
 Call trace:
 [<ffffff80082e2c2c>] debug_print_object+0xac/0xc8
 [<ffffff80082e40b0>] debug_check_no_obj_freed+0x1e8/0x228
 [<ffffff8008191254>] kfree+0x1cc/0x250
 [<ffffff80083cc03c>] hci_uart_tty_close+0x54/0x108
 [<ffffff800832e118>] tty_ldisc_close.isra.1+0x40/0x58
 [<ffffff800832e14c>] tty_ldisc_kill+0x1c/0x40
 [<ffffff800832e3dc>] tty_ldisc_release+0x94/0x170
 [<ffffff8008325554>] tty_release_struct+0x1c/0x58
 [<ffffff8008326400>] tty_release+0x3b0/0x490
 [<ffffff80081a3fe8>] __fput+0x88/0x1d0
 [<ffffff80081a418c>] ____fput+0xc/0x18
 [<ffffff80080c0624>] task_work_run+0x9c/0xc0
 [<ffffff80080a9e24>] do_exit+0x24c/0x8a0
 [<ffffff80080aa4e0>] do_group_exit+0x38/0xa0
 [<ffffff80080aa558>] __wake_up_parent+0x0/0x28
 [<ffffff8008082c00>] el0_svc_naked+0x34/0x38
 ---[ end trace bfe08cbd89098cdf ]---
Signed-off-by: NHermes Zhang <chenhuiz@axis.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In case memory resources for *fw* were allocated, release them before
return.

Addresses-Coverity-ID: 1472611 ("Resource leak")
Fixes: 7237c4c9 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

At the moment we only support ACPI enumeration for serial port attached
RTL bluetooth controllers.

This commit adds a dependency on ACPI to the BT_HCIUART_RTL configuration
option, fixing the following warning when ACPI is not enabled:

drivers/bluetooth/hci_h5.c:920:22: warning: 'rtl_vnd' defined but not used

Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We're supposed to pass the number of elements in the mtk_recv_pkts, not
the number of bytes.

Fixes: 7237c4c9 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Like all the other UART protocols, introduce a configuration option for
Realtek based serial devices.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This adds a driver based on serdev driver for the MediaTek serial protocol
based on running H:4, which can enable the built-in Bluetooth device inside
MT7622 SoC.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Using HCI_VENDOR_PKT for vendor specific events does work since it has
also the value 0xff, but it is actually the packet type indicator
constant and not the event constant. So introduce HCI_EV_VENDOR and
use it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This driver was recently updated to use serdev, so add the appropriate
dependency. Without this one can get compiler warnings like this if
CONFIG_SERIAL_DEV_BUS is not enabled:

  CC [M]  drivers/bluetooth/hci_h5.o
drivers/bluetooth/hci_h5.c:934:36: warning: ‘h5_serdev_driver’ defined but not used [-Wunused-variable]
 static struct serdev_device_driver h5_serdev_driver = {
                                    ^~~~~~~~~~~~~~~~
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add support to set voltage/current of various regulators
to power up/down Bluetooth chip wcn3990.
Signed-off-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch enables the RAM and NV patch download for wcn3990.
Signed-off-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Enable Qualcomm chips to operate at 3.2Mbps.
Signed-off-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In function qca_setup, we set initial and operating speeds for Qualcomm
Bluetooth SoC's. This block of code is common across different
Qualcomm Bluetooth SoC's. Instead of duplicating the code, created
a wrapper function to set the speeds. So that future coming SoC's
can use these wrapper functions to set speeds.
Signed-off-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Redefinition of qca_uart_setup will help future Qualcomm Bluetooth
SoC, to use the same function instead of duplicating the function.
Added new arguments soc_type and soc_ver to the functions.

These arguments will help to decide type of firmware files
to be loaded into Bluetooth chip.
soc_type holds the Bluetooth chip connected to APPS processor.
soc_ver holds the Bluetooth chip version.
Signed-off-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some of the QCA BTSoC ROME functions, are used for different versions
or different make of BTSoC's. Instead of duplicating the same functions
for new chip, update names of the functions that are used for both
chips to keep this generic and would help in future when we would have
new BT SoC. To have generic text in logs updated from ROME to QCA where
ever possible. This avoids confusion to user, when using the future
Qualcomm Bluetooth SoC's. Updated BT_DBG, BT_ERR and BT_INFO with
bt_dev_dbg, bt_dev_err and bt_dev_info where ever applicable.
Signed-off-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add support for the enable and device-wake GPIOs used on ACPI enumerated
RTL8723BS devices.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Implement support for the RTL8723BS chip.
Signed-off-by: NJeremy Cline <jeremy@jcline.org>
[hdegoede@redhat.com: Port from bt3wire.c to hci_h5.c, drop broken GPIO code]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Allow vendor-specific setup, open, and close functions to be defined.
Signed-off-by: NJeremy Cline <jeremy@jcline.org>
[hdegoede@redhat.com: Port from bt3wire.c to hci_h5.c, drop dt support]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add basic support for serdev enumerated devices, note sine this does
not (yet) declare any of / ACPI ids to bind to atm this is a nop.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The contents of the rtl_bt/rtlXXXX_config.bin file may be board specific
allow the caller of btrtl_initialize to specify a postfix identifying
the board, which if specified will make btrtl_initialize look for
rtl_bt/rtlXXXX_config-<postfix>.bin instead.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Realtek RTL8723BS and RTL8723DS chipsets are SDIO wifi chips. They
also contain a Bluetooth module which is connected via UART to the host.

Realtek's userspace initialization tool (rtk_hciattach) differentiates
these two via the HCI version and revision returned by the
HCI_OP_READ_LOCAL_VERSION command.
Additionally we apply these checks only the for UART devices. Everything
else is assumed to be a "RTL8723B" which was originally supported by the
driver (communicating via USB).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NJeremy Cline <jeremy@jcline.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The UART settings are embedded in the config blob. This has to be parsed
to successfully initialize the Bluetooth part of the RTL8723BS (which is
an SDIO chip, but the Bluetooth part is connected via UART).

The Realtek "rtl8723bs_bt" and "rtl8723ds_bt" userspace Bluetooth UART
initialization tools (rtk_hciattach) use the following sequence:
- send H5 sync pattern (already supported by hci_h5)
- get LMP version (already supported by btrtl)
- get ROM version (already supported by btrtl)
- load the firmware and config for the current chipset (already
  supported by btrtl)
- read UART settings from the config blob (part of this patch)
- send UART settings via a vendor command to the device (which changes
  the baudrate of the device and enables or disables flow control
  depending on the config)
- change the baudrate and flow control settings on the host
- send the firmware and config blob to the device (already supported by
  btrtl)

Sending the last firmware and config blob download command
(rtl_download_cmd) fails if the UART settings are not updated
beforehand. This is presumably because the device applies the config
right after the firmware and config blob download - which means that at
this point the host is using different UART settings than the device
(which will obviously result in non-working communication).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NJeremy Cline <jeremy@jcline.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>