Add an img-ir module for decoding the Sanyo infrared protocol.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add an img-ir module for decoding the Sharp infrared protocol.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add an img-ir module for decoding the Sony infrared protocol.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add an img-ir module for decoding the JVC infrared protocol.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add an img-ir module for decoding the NEC and extended NEC infrared
protocols.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add ImgTec IR decoder driver to the build system.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add remote control input driver for the ImgTec Infrared block hardware
decoder, which is set up with timings for a specific protocol and
supports mask/value filtering and wake events.

The hardware decoder timing values, raw data to scan code conversion
function and scan code filter to raw data filter conversion function
will be provided in separate files for each protocol which this part of
the driver can use. The new generic scan code filter interface is made
use of to reduce interrupts and control wake events.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add raw IR remote control input driver for the ImgTec Infrared decoder
block's raw edge interrupts. Generic software protocol decoders are used
to allow multiple protocols to be supported at a time, including those
not supported by the hardware decoder.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add base driver for the ImgTec Infrared decoder block. The driver is
split into separate components for raw (software) decode and hardware
decoder which are in following commits.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add device tree binding for ImgTec Consumer Infrared block, specifically
major revision 1 of the hardware.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When either of the normal or wakeup filter protocols are changed,
refresh the corresponding scancode filter, i.e. try and set the same
scancode filter with the new protocol. If that fails clear the filter
instead.

If no protocol was selected the filter is just cleared, and if no
s_filter callback exists the filter is left unmodified.

Similarly clear the filter mask when the filter is set if no protocol is
currently selected.

This simplifies driver code which no longer has to explicitly worry
about modifying the filter on a protocol change. This also allows the
change_wakeup_protocol callback to be omitted entirely if there is only
a single available wakeup protocol at a time, since selecting no
protocol will automatically clear the wakeup filter, disabling wakeup.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a wakeup_protocols sysfs file which controls the new
rc_dev::enabled_protocols[RC_FILTER_WAKEUP], which is the mask of
protocols that are used for the wakeup filter.

A new RC driver callback change_wakeup_protocol() is called to change
the wakeup protocol mask.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Only a single allowed and enabled protocol mask currently exists in
struct rc_dev, however to support a separate wakeup filter protocol two
of each are needed, ideally as an array.

Therefore make both rc_dev::allowed_protos and rc_dev::enabled_protocols
arrays, update all users to reference the first element
(RC_FILTER_NORMAL), and add a couple more helper functions for drivers
to use for setting the allowed and enabled wakeup protocols.

We also rename allowed_protos to allowed_protocols while we're at it,
which is more consistent with enabled_protocols.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add generic scancode filtering of RC input events, and fall back to
permitting any RC_FILTER_NORMAL scancode filter to be set if no s_filter
callback exists. This allows raw IR decoder events to be filtered, and
potentially allows hardware decoders to set looser filters and rely on
generic code to filter out the corner cases.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

On certain motherboards (mainly Intel NUC series) bios keeps the
Nuvoton CIR device disabled at boot.

This patch adds a call to kernel PNP layer to activate the device if it
is not already activated. This will improve the chances of the PNP probe
actually succeeding on Intel NUC platforms.
Signed-off-by: NAntti Seppälä <a.seppala@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

DViCO FusionHDTV7 device that use au0828 can fail to communicate with
xc5000 using i2c interface because of high i2c clock speed - i2c clock
stretching bug. It causes to fail xc5000 firmware loading normally at
the current driver.

Already this problem fixed as changing to low i2c clock speed at
HVR-950q device, also DViCO FusionHDTV7 device can solve it as using low
i2c clock speed - 20KHz.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Propagate errors returned by drivers from the s_filter callback back to
userland when updating scancode filters. This allows userland to see
when the filter couldn't be updated, usually because it's not a valid
filter for the hardware.

Previously the filter was being updated conditionally on success of
s_filter, but the write always reported success back to userland.
Reported-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a device id to support for PX-S1UD (PLEX ISDB-T usb dongle) which
has sms2270.
Signed-off-by: NSatoshi Nagahama <sattnag@aim.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Since the introduction of the new OMAP DSS DVI connector driver in
commit 348077b1 ("OMAPDSS: Add new DVI
Connector driver"), DVI outputs report a new display type of
OMAP_DISPLAY_TYPE_DVI instead of OMAP_DISPLAY_TYPE_DPI. Handle the new
type in the IRQ handler.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

New board addition. No other changes.

[m.chehab@samsung.com: rebase patch and fix whitespace mangling]
Signed-off-by: NPojar George <geoubuntu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

These chips makes use of the media_entity in the v4l2_subdev struct
and is therefor dependent of the  MEDIA_CONTROLLER config.
Signed-off-by: NMarcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix this linker warning:
WARNING: "__divdi3" [media_build/v4l/drx39xyj.ko] undefined!

[m.chehab@samsung.com: add include for asm/div64.h]
Signed-off-by: NGianluca Gennari <gennarone@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

try_fmt should just set field to NONE and not return an error if
a different field was passed.

buf_prepare should check if the field passed in from userspace has a
supported field value. At the moment only NONE is supported and ANY
is mapped to NONE.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

- Set the sequence counters correctly.
- Copy timestamps, timecode, relevant buffer flags and field from
  the received buffer to the outgoing buffer.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

To keep the vb2 buffer administration in balance stop_streaming() must
return any pending buffers to the vb2 framework.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is no reason why we shouldn't enable this here.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

v4l2_compliance fix.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This resolves an issue raised by v4l2-compliance: if the given format does
not exist, then pick a default format.

While there is an exception regarding this for TV capture drivers, this
m2m driver should do the right thing.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The default of 1 second is a bit painful, switch to a 25 Hz framerate.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch removes meaningless assignment of memory bank to itself.
Signed-off-by: NSeung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is no any reason to use comma here.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The adv7180 has a low power mode in which the analog and the digital processing
section are shut down. Implement the s_power callback to let bridge drivers put
the part into low power mode when not needed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for async device registration to the adv7180 driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The proper way to handle IRQs that need to be able to sleep in their IRQ handler
is to use a threaded IRQ.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The device driver core already prints out a very similar message when a driver
fails to probe. No need to print one in the driver itself.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The device can't possibly be registered at this point, so no need to to call
v4l2_device_unregister_subdev().
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Make sure to free the control handler when the device is removed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The mutex is used in the subdev callbacks, so unregister the subdev before the
mutex is destroyed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Document that it is now possible to call G/S_EDID from video nodes, not
just sub-device nodes. Add a note that -EINVAL will be returned if
the pad does not support EDIDs.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>