Add support for offloading PRIO qdisc as root qdisc.
The support is for up to 8 bands.
Routed packets priority is determined by the DSCP field with the default
translations. Bridged packets priority is determined by the PCP field, if
exist, otherwise it is set to 0.
Since both options have only priorities 0-7, higher priorities mapping are
being ignored.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When routing ip packets, the kernel is setting the SKB's priority
based on the tos field of the packet.
Imitate this behavior in the mlxsw router, having the internal
switch priority of a routed packet determined according to its DS
field.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add rdpm definition - router DSCP to priority mapping register.
This register will be utilized later to align the default mapping between
packet DSCP and switch-priority to the kernel's mapping between
packet priority and skb priority.

This is the first non-bit indexed register where the entries are arranged
in descending order, i.e., entry at offset 0 matches configuration for
dscp[63]. As a result, the item's step is converted into a signed variable
to support descending arrays [where step would be negative].
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is a problem with the VTU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is a problem with the ATU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit eb789980 ("mlxsw: spectrum_router: Populate adjacency
entries according to weights") the driver includes support for
non-equal-cost multipath, but IPv4 nexthops were the only user.

Now that the kernel supports weighted IPv6 nexthops, we can extend the
driver to support it as well.

This is done by assigning each nexthop its configured weight, so that it
will be populated accordingly in the device's adjacency table. The
`weight` parameter is also taken into account when comparing nexthop
groups in order not to consolidate non-identical groups.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On targets that have different sizes for phys_addr_t and dma_addr_t,
we get a type mismatch error:

drivers/net/ethernet/socionext/netsec.c: In function 'netsec_alloc_dring':
drivers/net/ethernet/socionext/netsec.c:970:9: error: passing argument 3 of 'dma_zalloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]

The code is otherwise correct, as the address is never actually used as a
physical address but only passed into a DMA register.  For consistently,
I'm changing the variable name as well, to clarify that this is a DMA
address.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's necessary to check hook whether being defined before
calling, improve the reliability.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Local variable "changed" was defined to indicates features changed,
but was used only for feature NETIF_F_HW_VLAN_CTAG_RX. Add checking
for other features.

Fixes: 052ece6d ("net: hns3: add ethtool related offload command")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the int_gl_idx does not be set, the default interrupt coalesce index
is 0. The TX queues and the RX queues will both use the GL0 as the
interrupt coalesce GL switch. But it should be GL1 for TX queues and GL0
for RX queues.

This patch adds the int_gl_idx setup for TX queues and RX queues.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, driver used 2us as the GL unit. The time unit ethtool
command "-c" and "-C" use is 1us, so now the GL unit driver uses
actually is 1us.

This patch changes the unit of GL value macro from
2us to 1us.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the TX GL and the RX GL need to be set separately,
hns3_set_vector_coalesc_gl() has been replaced with
hns3_set_vector_coalesce_rx_gl() and hns3_set_vector_coalesce_tx_gl().

This patch removes hns3_set_vector_coalesc_gl().
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GL update function uses the max GL value between tx_int_gl and
rx_int_gl to set both new tx_int_gl and new rx_int_gl. Therefore, User
can not enable TX GL self-adaptive or RX GL self-adaptive individually.

This patch refactors the code to update the TX GL and the RX GL
separately, making user can enable TX GL self-adaptive or RX GL
self-adaptive individually.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the hardware, the coalesce configurable registers include GL0, GL1,
GL2. In the driver, the TX queues use the register GL1 and the RX queues
use the register GL0. This function initializes the configuration of the
interrupt coalescing, but does not distinguish between the TX direction
and the RX direction. It will cause some confusion.

This patch refactors the function to initialize the TX GL and the RX GL
separately. And the initialization of related variables also is added to
this patch.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds ethtool_ops.set_coalesce support to PF.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds ethtool_ops.get_coalesce support to PF.

Whilst our hardware supports per queue values, external interfaces
support only a single shared value. As such we use the values for
queue 0.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only main PF can config TSO MSS length according to hardware.
This patch removes TSO config command from VF driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch supports the ethtool's get_channels() for VF.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.

This is detected by Coccinelle semantic patch.

@@
expression pdev, res, n, t, e, e1, e2;
@@

res = platform_get_resource(pdev, t, n);
+ if (!res)
+   return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return error code -ENODEV from the of_phy_connect() error
handling case instead of 0, as done elsewhere in this function.

Fixes: 533dd11a ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I ran into a randconfig build failure:

drivers/net/ethernet/socionext/netsec.c: In function 'netsec_probe':
drivers/net/ethernet/socionext/netsec.c:1583:17: error: implicit declaration of function 'devm_ioremap'; did you mean 'ioremap'? [-Werror=implicit-function-declaration]

Including linux/io.h directly fixes this.

Fixes: 533dd11a ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initiating a kdump via the command line can cause a pending interrupt
to be handled by the ibmvnic driver when initializing the sub-CRQ
irqs during driver initialization.

NIP [d000000000ca34f0] ibmvnic_interrupt_rx+0x40/0xd0 [ibmvnic]
LR [c000000008132ef0] __handle_irq_event_percpu+0xa0/0x2f0
Call Trace:
[c000000047fcfde0] [c000000008132ef0] __handle_irq_event_percpu+0xa0/0x2f0
[c000000047fcfea0] [c00000000813317c] handle_irq_event_percpu+0x3c/0x90
[c000000047fcfee0] [c00000000813323c] handle_irq_event+0x6c/0xd0
[c000000047fcff10] [c0000000081385e0] handle_fasteoi_irq+0xf0/0x250
[c000000047fcff40] [c0000000081320a0] generic_handle_irq+0x50/0x80
[c000000047fcff60] [c000000008014984] __do_irq+0x84/0x1d0
[c000000047fcff90] [c000000008027564] call_do_irq+0x14/0x24
[c00000003c92af00] [c000000008014b70] do_IRQ+0xa0/0x120
[c00000003c92af50] [c000000008002594] hardware_interrupt_common+0x114/0x180
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add changes to t4_eth_xmit to enable vxlan segmentation
offload support.

Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ndo_udp_tunnel_add and ndo_udp_tunnel_del
to support vxlan tunnelling.

Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add data structures and macros to be used in vxlan
offload.

Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store and handle ethtool link mode masks within the driver instead of
 just a single u32.  However, quite a significant amount of existing code
 wants to manipulate the masks directly, and thus now uses the first
 unsigned long (i.e. mask[0]) as though it were a legacy u32 mask.  This
 is ok because all the bits that code is interested in are in the first
 32 bits of the mask; but it might be a good idea to change them in
 future to use the proper bitmap API.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only handles direct speed setting, not autoneg, because the driver is
 still trying to pretend it uses the legacy ethtool API which doesn't
 have advertised/supported bits for 25/50/100G.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a qdisc is being replaced by another qdisc of the same type, it can
simply override over its configuration.
However, if it replaces a qdisc of another type, it needs to be removed
before setting the new qdisc.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a generic qdisc replace function.
For that goal, add three functions to the qdisc ops struct:
* check_params: Checks if the given parameters are offloadable.
* replace: Offload the given parameters.
* clean_stats: clean the qdisc stats for the offloaded qdisc.
integrate RED offloading into using the new internal replace API.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a destroy function to the qdiscs ops struct.
Create a generic qdisc destroy function, that clears the qdisc metadata as
well as calling the specific qdisc destroy function.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Qdisc struct have the Qdisc_class_ops struct.
This patch introduces the similar ops struct for the mlxsw_sp_qdisc_ops
struct. It allows better readability as well as code reusability for the
common parts of some functions like destroy.
The first operations to be added are the statistics getters.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every qdisc op gets the qdisc handle ID as well as its location.  Each one
of them, beside replace, checks if the handle doesn't match the qdisc in
the given location, and if so, it returns without running the actual op.
Unite these checks to one comparison function and avoid sending the handle
id to these ops.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tclass number is needed for most of the operations related to the qdisc in
the driver. Create a field for it in the mlxsw_sp_qdisc instead of passing
it to every function as parameter.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve readability by changing the clean stats function to handle only
RED. Qdiscs that will be offloaded in the future will have a clean stats
function of their own.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean RED offloaded stats and make them more generic by breaking the
generic qdisc stats to a struct of their own.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the value of the xstats requested from the driver for offloaded RED
to be incremental, like the normal stats.
It increases consistency - if a qdisc stops being offloaded its xstats
don't change.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the name of the stats struct to be generic, so it could be used for
other qdisc offload, that will be added in the next patches.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all the qdisc related data from the spectrum.h to spectrum_qdisc.c.
Create an init and fini functions for the qdiscs.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>