This is sufficient to allow boot of the Lager board with
a console without boards-lager.c compiled into the kernel.
This is an example of a minimal but still useful initialisation
of the board using DT as much as possible.

As such it is the same as the boot of Lager that can be achieved
without a board file. The intention of adding this file
is to facilitate further work to allow board specific devices to be
initialised via DT.
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds a sample DT-based APE6EVM "reference" implementation. The
use of platform-specific C-code should be avoided with this configuration
as much as possible.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a DT reference implementation for the KZM9D board.

Only DT devices are used in this case. UART, STI, GPIO
and SMP / GIC are all provided by emev2.dtsi.

There is still a board specific C file used for enabling
legacy SH clocks. This file will be removed after we have
moved over to common clocks.
Signed-off-by: NMagnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Do not include trailing blank line in
 board-kzm9d-reference.c ]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Remove board support for the r8a7740 based Bonito board

The r8a7740 SoC support code is still kept around since it
is in use by the Armadillo800eva board which is basically a more
recent board where the design is based on Bonito.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Remove board support for the sh7372 based AP4EVB board

The sh7372 SoC support code is still kept around since it
is in use by the Mackerel board which is basically a more
recent board where the design is based on AP4EVB.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is V2 of the mach-shmobile uImage load address rework patch.

Rework the mach-shmobile uImage load address calculation by storing
the per-board load addresses in Makefile.boot. This removes the
CONFIG_MEMORY_START dependency from Makefile.boot, and it also makes
it possible to create safe kernel images that boot on multiple boards.

This is one of several series of code that reworks code not to rely on
CONFIG_MEMORY_START/SIZE which in turn is needed for ARCH_MULTIPLATFORM.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Since the dtb targets have moved to arch/arm/boot/dts/Makefile, sweep
the platforms that have had new targets added recently and move them over.

While I was at it, I also made the dtb generation more generic, i.e. if
the platform is enabled then all dtbs for that platform will be created.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brown <davidb@codeaurora.com>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>

Add compilation support for dtbs using 'make dtbs'

Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: NTetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: NSimon Horman <horms@verge.net.au>

Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds preliminary support for the SH-Mobile G-series.

The SH-Mobile G-series is a series of ARM/SH multi-core CPUs that aside
from the ARM MPU are primarily composed of existing SH IP blocks.

This includes initial support for the SH7367 (SH-Mobile G3) CPU and
the G3EVM reference board.

Only timer, serial console, and NOR flash are supported at this point.
Patches for the interrupt controller, pinmux support, clock framework
and runtime pm will be submitted as feature patches on top of this.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>