When closing the ibmvnic driver we need to wait for any pending
sub crq entries to ensure they are handled.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When closing the ibmvnic driver, most notably during the reset
path, the tx pools need to be cleaned to ensure there are no
hanging skbs that need to be free'ed.

The need for this was found during debugging a loss of network
traffic after handling a driver reset. The underlying cause was
some skbs in the tx pool that were never free'ed. As a
result the upper network layers never tried a re-send since it
believed the driver still had the skb.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The napi structs allocated at drivier initializatio need to be
free'ed when releasing the drivers resources.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ibmvnic driver has multiple handlers for resetting the driver
depending on the reason the reset is needed (failover, lpm,
fatal erors,...). All of the reset handlers do essentially the same
thing, this patch moves this work to a common reset handler.

By doing this we also allow the driver to better handle situations
where we can get a reset while handling a reset.

The updated reset handling works by adding a reset work item to the
list of resets and then scheduling work to perform the reset. This
step is necessary because we can receive a reset in interrupt context
and we want to handle the reset out of interrupt context.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the is_closed flag in the ibmvnic adapter strcut with a
more comprehensive state field that tracks the current state of
the driver.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all of the calls to initialize resources for the driver to
a separate routine.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for Telit ME910 PID 0x1100.
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now tg3 NIC's stats will be cleared after ifdown/ifup. bond_get_stats traverse
its salves to get statistics,cumulative the increment.If a tg3 NIC is added to
bonding as a slave,ifdown/ifup will cause bonding's stats become tremendous value
(ex.1638.3 PiB) because of negative increment.

Fixes: 92feeabf ("tg3: Save stats across chip resets")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Small follow-up to d74a32ac ("xdp: use netlink extended ACK reporting")
in order to let drivers all use the same NL_SET_ERR_MSG_MOD() helper macro
for reporting. This also ensures that we consistently add the driver's
prefix for dumping the report in user space to indicate that the error
message is driver specific and not coming from core code. Furthermore,
NL_SET_ERR_MSG_MOD() now reuses NL_SET_ERR_MSG() and thus makes all macros
check the pointer as suggested.

References: https://www.spinics.net/lists/netdev/msg433267.htmlSigned-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding support for Microchip LAN9250 Ethernet controller.
Signed-off-by: NDavid Cai <david.cai@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver follows a method of taking one extra reference on the
page for recycling which is fine in usual packet path where
each 64KB page is segmented into multiple receive buffers.

But in XDP mode since there is just one receive buffer per
page taking extra page reference itself becomes big bottleneck
consuming ~50% of CPU cycles due to atomic operations.

This patch adds a internal ref count in pgcache for each
page and additional page references are taken in a batch
instead of just one at a time. Internal i.e 'pgcache->ref_count'
and page's i.e 'page->_refcount' counters are compared to check
page's recyclability.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When in XDP mode reserve XDP_PACKET_HEADROOM bytes at the start
of receive buffer for XDP program to modify headers and adjust
packet start. Additional code changes done to handle such packets.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for XDP_TX i.e transmits packet out of
the XDP TX queue mapped to the corresponding Rx queue
on which packet is received.

Since SQ for XDP TX will be used only on a single cpu i.e
SQ description creation and freeing, using atomic free count
is not necessary and will become a bottleneck. Hence added
a separate 'xdp_free_cnt' used for SQs designated for XDP
to track descriptor free count.

Changes also include
- A new entry 'xdp_page' is added to save transmitted packet's
  page pointer for later cleanup.
- XDP Tx SQ's doorbell is ringed once per NAPI instance.
- Retrieving designated SQ for packets being sent out by stack
  via 'nicvf_xmit'.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for XDP_DROP.
Also since in XDP mode there is just a single buffer per page,
made changes to recycle DMA mapping info as well along with pages.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds basic XDP support i.e attaching a BPF program to an
interface. Also takes care of allocating separate Tx queues
for XDP path and for network stack packet transmission.

This patch doesn't support handling of any of the XDP actions,
all are treated as XDP_PASS i.e packets will be handed over to
the network stack.

Changes also involve allocating one receive buffer per page in XDP
mode and multiple in normal mode i.e when no BPF program is attached.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of unnecessary double pointer references and type casting
in receive buffer allocation code.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimized CQE handling with below changes
- Feeing descriptors back to SQ in bulk i.e once per NAPI
  instance instead for every CQE_TX, this will reduce number
  of atomic updates to 'sq->free_cnt'.
- Checking errors in CQE_TX and CQE_RX before calling appropriate
  fn()s to update error stats i.e reduce branching.

Also removed debug messages in packet handling path which otherwise
causes issues if DEBUG is enabled.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Receive buffer's physical address or iova will anyway not
go beyond 49bits, since it is the max supported HW address.
As per perf, updating bitfields i.e buf_addr:42 in RBDR
descriptor entry consumes lots of cpu cycles, hence changed
it to a 64bit field with alignment requirements taken care of.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for page recycling for allocating receive buffers
to reduce cost of refilling RBDR ring. Also got rid of using
compound pages when pagesize is 4K, only order-0 pages now.

Only page is recycled, DMA mappings still needs to be done for
every receive buffer allocated due to following constraints
- Cannot have just one receive buffer per 64KB page.
- There is just one buffer ring shared across 8 Rx queues, so
  buffers of same page can go to any Rx queue.
- HW gives buffer address where packet has been DMA'ed and not
  the index into buffer ring.
This makes it not possible to resue DMA mapping info. So unfortunately
have to go through costly mapping route for every buffer.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
 1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
    TimeSync/"V1 frame format support"/"V2 frame format support" on
    the TX side. Set the associated bits based on the user request.
 2. ptp4l application fails to operate in Peer Delay mode. Following
    changes are needed to fix this,
    a. Driver should enable (set to 0) DA #1-related bits for IPv4,
       IPv6 and MAC destination addresses in these registers:
         NIG_REG_TX_LLH_PTP_RULE_MASK
         NIG_REG_LLH_PTP_RULE_MASK
    b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
       be set to 0x0 in all modes.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP Tx timestamping data structures are not protected against the
concurrent access in the Tx paths. Protecting the same using atomic
bit locks.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IOT2000 is industrial controller platform, derived from the Intel
Galileo Gen2 board. The variant IOT2020 comes with one LAN port, the
IOT2040 has two of them. They can be told apart based on the board asset
tag in the DMI table.

Based on patch by Sascha Weisenberger.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NSascha Weisenberger <sascha.weisenberger@siemens.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns_get_sset_count() returns HNS_NET_STATS_CNT and the data space allocated
is not enough for ethtool_get_strings(), which will cause random memory
corruption.

When SLAB and DEBUG_SLAB are both enabled, memory corruptions like the
the following can be observed without this patch:
[   43.115200] Slab corruption (Not tainted): Acpi-ParseExt start=ffff801fb0b69030, len=80
[   43.115206] Redzone: 0x9f911029d006462/0x5f78745f31657070.
[   43.115208] Last user: [<5f7272655f746b70>](0x5f7272655f746b70)
[   43.115214] 010: 70 70 65 31 5f 74 78 5f 70 6b 74 00 6b 6b 6b 6b  ppe1_tx_pkt.kkkk
[   43.115217] 030: 70 70 65 31 5f 74 78 5f 70 6b 74 5f 6f 6b 00 6b  ppe1_tx_pkt_ok.k
[   43.115218] Next obj: start=ffff801fb0b69098, len=80
[   43.115220] Redzone: 0x706d655f6f666966/0x9f911029d74e35b.
[   43.115229] Last user: [<ffff0000084b11b0>](acpi_os_release_object+0x28/0x38)
[   43.115231] 000: 74 79 00 6b 6b 6b 6b 6b 70 70 65 31 5f 74 78 5f  ty.kkkkkppe1_tx_
[   43.115232] 010: 70 6b 74 5f 65 72 72 5f 63 73 75 6d 5f 66 61 69  pkt_err_csum_fai
Signed-off-by: NTimmy Li <lixiaoping3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 6390 family of chips use only 2 of the 3 VTU Data registers to pack
the MemberTag and PortState VLAN data. This means that they must be
written or read before or after each VTU/STU operations.

Implement this variant to add support for VTU with such chips. These
chips have a 13th bit for the VID thus set their max_vid to 8191.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer chips such as the 88E6390 have a VTU Page bit in the VTU VID
register to specify a 13th bit for the VID. This can be used to support
8K VLANs.

When dumping the whole VTU, all VID bits must be set to one, including
this VTU Page bit. Add support for VID greater than 4095.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the code which fetches or initializes a new VTU entry more concise.
This allows us the get rid of the old underscore prefix naming.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have chip operations for VTU accesses, mark all helpers from
global1_vtu.c as static. Only the various implementations of the
GetNext, LoadPurge and Flush operations need to be exposed.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new vtu_loadpurge operation to the chip info structure to differ
the various implementations of the VTU accesses.

Now that the STU handling is abstracted behind VTU operations, kill the
obsolete MV88E6XXX_FLAG_STU flag.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new vtu_getnext operation to the chip info structure to differ the
various implementations of the VTU accesses.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the code writes both VTU and STU data when loading a VTU entry,
load the corresponding STU entry at the same time.

This allows us to get rid of the STU management in the
_mv88e6xxx_vtu_new helper and thus remove the separate implementations
of STU Load/Purge and STU GetNext, as well as the unused family checks.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the code reads both VTU and STU data on VTU GetNext operation,
fetch the STU entry data of a VTU entry at the same time.

The STU data bits are masked with the VTU data bits and they are now all
read at the same time a VTU GetNext operation is issued.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the generic portion of code to issue an STU GetNext operation,
which will be used in other implementations.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code to access the VTU Data registers currently only supports the
88E6185 family and alike: 2-bit membership adjacent to 2-bit port state.

Even though the 88E6352 family introduced an indirect table to program
the VLAN Spanning Tree states, the usage of the VTU Data registers
remains the same regardless the VTU or STU operation.

Now that the mv88e6xxx_vtu_entry structure contains both port membership
and states data, factorize the code to access them in global1_vtu.c.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even though every switch model has a different way to access the VTU
Data bits, the base implementation of the VTU GetNext operation remains
the same: wait, write the first VID to iterate from, start the
operation, and read the next VID.

Move this generic implementation into global1_vtu.c and abstract the
handling of the start VID (similarly to the ATU GetNext implementation),
before introducing a new chip operation for specific chips.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helpers to access the VTU VID register in the global1_vtu.c file.

At the same time, move mv88e6xxx_g1_vtu_vid_write at the beginning of
_mv88e6xxx_vtu_loadpurge, which adds no functional changes but makes
future patches simpler.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helpers to access the VTU SID register in the global1_vtu.c file.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helpers to access the VTU FID register in the global1_vtu.c file.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the VTU flush operation to global1_vtu.c and call it from a
mv88e6xxx_vtu_setup helper, similarly to the ATU and PVT setup.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the helper functions to access the Global 1 VTU Operation register
to a new global1_vtu.c file, and get rid of the old underscore prefix
naming convention. This file will be extended will all VTU/STU related
code.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>