- 25 8月, 2016 5 次提交
-
-
由 Shaohua Li 提交于
bio_reset doesn't change bi_io_vec and bi_max_vecs, so we don't need to set them every time. bi_private will be set before the bio is dispatched. Signed-off-by: NShaohua Li <shli@fb.com> -
由 Shaohua Li 提交于
Yi reported a memory leak of raid5 with DIF/DIX enabled disks. raid5 doesn't alloc/free bio, instead it reuses bios. There are two issues in current code: 1. the code calls bio_init (from init_stripe->raid5_build_block->bio_init) then bio_reset (ops_run_io). The bio is reused, so likely there is integrity data attached. bio_init will clear a pointer to integrity data and makes bio_reset can't release the data 2. bio_reset is called before dispatching bio. After bio is finished, it's possible we don't free bio's integrity data (eg, we don't call bio_reset again) Both issues will cause memory leak. The patch moves bio_init to stripe creation and bio_reset to bio end io. This will fix the two issues. Reported-by: NYi Zhang <yizhan@redhat.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
由 Tomasz Majchrzak 提交于
For failed write request record block address on a device, not block address in an array. Signed-off-by: NTomasz Majchrzak <tomasz.majchrzak@intel.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
由 Wei Yongjun 提交于
Fix to return error code -ENOMEM from the lockres_init() error handling case instead of 0, as done elsewhere in this function. Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
由 Song Liu 提交于
Currently, the code sets MD_JOURNAL_CLEAN when the array has MD_FEATURE_JOURNAL and the recovery_cp is MaxSector. The array will be MD_JOURNAL_CLEAN even if the journal device is missing. With this patch, the MD_JOURNAL_CLEAN is only set when the journal device presents. Signed-off-by: NSong Liu <songliubraving@fb.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
- 18 8月, 2016 2 次提交
-
-
由 Artur Paszkiewicz 提交于
This fixes a long-standing bug that caused a flood of messages like: "md: delaying data-check of md1 until md2 has finished (they share one or more physical units)" It can be reproduced like this: 1. Create at least 3 raid1 arrays on a pair of disks, each on different partitions. 2. Request a sync operation like 'check' or 'repair' on 2 arrays by writing to their md/sync_action attribute files. One operation should start and one should be delayed and a message like the above will be printed. 3. Issue a write to the third array. Each write will cause 2 copies of the message to be printed. This happens when wake_up(&resync_wait) is called, usually by md_check_recovery(). Then the delayed sync thread again prints the message and is put to sleep. This patch adds a check in md_do_sync() to prevent printing this message more than once for the same pair of devices. Reported-by: NSven Koehler <sven.koehler@gmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=151801Signed-off-by: NArtur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
由 Guoqing Jiang 提交于
The ret is not needed anymore since we have already move resync_start into md_do_sync in commit 41a9a0dc. Reviewed-by: NNeilBrown <neilb@suse.com> Signed-off-by: NGuoqing Jiang <gqjiang@suse.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
- 17 8月, 2016 1 次提交
-
-
由 Song Liu 提交于
GET_ARRAY_INFO counts journal as spare (spare_disks), which is not accurate. This patch fixes this. Reported-by: NYi Zhang <yizhan@redhat.com> Signed-off-by: NSong Liu <songliubraving@fb.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
- 06 8月, 2016 2 次提交
-
-
由 Alexey Obitotskiy 提交于
After array enters in faulty state (e.g. number of failed drives becomes more then accepted for raid5 level) it sets error flags (one of this flags is MD_CHANGE_PENDING). For internal metadata arrays MD_CHANGE_PENDING cleared into md_update_sb, but not for external metadata arrays. MD_CHANGE_PENDING flag set prevents to finish all new or non-finished IOs to array and hold them in pending state. In some cases this can leads to deadlock situation. For example, we have faulty array (2 of 4 drives failed) and udev handle array state changes and blkid started (or other userspace application that used array to read/write) but unable to finish reads due to IO hold. At the same time we unable to get exclusive access to array (to stop array in our case) because another external application still use this array. Fix makes possible to return IO with errors immediately. So external application can finish working with array and give exclusive access to other applications to perform required management actions with array. Signed-off-by: NAlexey Obitotskiy <aleksey.obitotskiy@intel.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
由 Shaohua Li 提交于
Changing the location changes a lot of things. Holding the lock to avoid race. This makes the .quiesce called with mddev lock hold too. Acked-by: NNeilBrown <neilb@suse.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
- 02 8月, 2016 1 次提交
-
-
由 ZhengYuan Liu 提交于
The counter conf->empty_inactive_list_nr is only used for determine if the raid5 is congested which is deal with in function raid5_congested(). It was increased in get_free_stripe() when conf->inactive_list got to be empty and decreased in release_inactive_stripe_list() when splice temp_inactive_list to conf->inactive_list. However, this may have a problem when raid5_get_active_stripe or stripe_add_to_batch_list was called, because these two functions may call list_del_init(&sh->lru) to delete sh from "conf->inactive_list + hash" which may cause "conf->inactive_list + hash" to be empty when atomic_inc_not_zero(&sh->count) got false. So a check should be done at these two point and increase empty_inactive_list_nr accordingly. Otherwise the counter may get to be negative number which would influence async readahead from VFS. Signed-off-by: NZhengYuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: NShaohua Li <shli@fb.com>
-
- 31 7月, 2016 1 次提交
-
-
由 Tomasz Majchrzak 提交于
md pending write counter must be incremented after bio is split, otherwise it gets decremented too many times in end bio callback and becomes negative. Signed-off-by: NTomasz Majchrzak <tomasz.majchrzak@intel.com> Reviewed-by: NArtur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
- 29 7月, 2016 7 次提交
-
-
由 Andy Lutomirski 提交于
Currently, NR_KERNEL_STACK tracks the number of kernel stacks in a zone. This only makes sense if each kernel stack exists entirely in one zone, and allowing vmapped stacks could break this assumption. Since frv has THREAD_SIZE < PAGE_SIZE, we need to track kernel stack allocations in a unit that divides both THREAD_SIZE and PAGE_SIZE on all architectures. Keep it simple and use KiB. Link: http://lkml.kernel.org/r/083c71e642c5fa5f1b6898902e1b2db7b48940d4.1468523549.git.luto@kernel.orgSigned-off-by: NAndy Lutomirski <luto@kernel.org> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Acked-by: NJohannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Reviewed-by: NJosh Poimboeuf <jpoimboe@redhat.com> Reviewed-by: NVladimir Davydov <vdavydov@virtuozzo.com> Acked-by: NMichal Hocko <mhocko@suse.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mel Gorman 提交于
There are now a number of accounting oddities such as mapped file pages being accounted for on the node while the total number of file pages are accounted on the zone. This can be coped with to some extent but it's confusing so this patch moves the relevant file-based accounted. Due to throttling logic in the page allocator for reliable OOM detection, it is still necessary to track dirty and writeback pages on a per-zone basis. [mgorman@techsingularity.net: fix NR_ZONE_WRITE_PENDING accounting] Link: http://lkml.kernel.org/r/1468404004-5085-5-git-send-email-mgorman@techsingularity.net Link: http://lkml.kernel.org/r/1467970510-21195-20-git-send-email-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net> Acked-by: NVlastimil Babka <vbabka@suse.cz> Acked-by: NMichal Hocko <mhocko@suse.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Acked-by: NJohannes Weiner <hannes@cmpxchg.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Rik van Riel <riel@surriel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mel Gorman 提交于
NR_FILE_PAGES is the number of file pages. NR_FILE_MAPPED is the number of mapped file pages. NR_ANON_PAGES is the number of mapped anon pages. This is unhelpful naming as it's easy to confuse NR_FILE_MAPPED and NR_ANON_PAGES for mapped pages. This patch renames NR_ANON_PAGES so we have NR_FILE_PAGES is the number of file pages. NR_FILE_MAPPED is the number of mapped file pages. NR_ANON_MAPPED is the number of mapped anon pages. Link: http://lkml.kernel.org/r/1467970510-21195-19-git-send-email-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net> Acked-by: NVlastimil Babka <vbabka@suse.cz> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Rik van Riel <riel@surriel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mel Gorman 提交于
Reclaim makes decisions based on the number of pages that are mapped but it's mixing node and zone information. Account NR_FILE_MAPPED and NR_ANON_PAGES pages on the node. Link: http://lkml.kernel.org/r/1467970510-21195-18-git-send-email-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net> Acked-by: NVlastimil Babka <vbabka@suse.cz> Acked-by: NMichal Hocko <mhocko@suse.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Acked-by: NJohannes Weiner <hannes@cmpxchg.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Rik van Riel <riel@surriel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mel Gorman 提交于
This moves the LRU lists from the zone to the node and related data such as counters, tracing, congestion tracking and writeback tracking. Unfortunately, due to reclaim and compaction retry logic, it is necessary to account for the number of LRU pages on both zone and node logic. Most reclaim logic is based on the node counters but the retry logic uses the zone counters which do not distinguish inactive and active sizes. It would be possible to leave the LRU counters on a per-zone basis but it's a heavier calculation across multiple cache lines that is much more frequent than the retry checks. Other than the LRU counters, this is mostly a mechanical patch but note that it introduces a number of anomalies. For example, the scans are per-zone but using per-node counters. We also mark a node as congested when a zone is congested. This causes weird problems that are fixed later but is easier to review. In the event that there is excessive overhead on 32-bit systems due to the nodes being on LRU then there are two potential solutions 1. Long-term isolation of highmem pages when reclaim is lowmem When pages are skipped, they are immediately added back onto the LRU list. If lowmem reclaim persisted for long periods of time, the same highmem pages get continually scanned. The idea would be that lowmem keeps those pages on a separate list until a reclaim for highmem pages arrives that splices the highmem pages back onto the LRU. It potentially could be implemented similar to the UNEVICTABLE list. That would reduce the skip rate with the potential corner case is that highmem pages have to be scanned and reclaimed to free lowmem slab pages. 2. Linear scan lowmem pages if the initial LRU shrink fails This will break LRU ordering but may be preferable and faster during memory pressure than skipping LRU pages. Link: http://lkml.kernel.org/r/1467970510-21195-4-git-send-email-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net> Acked-by: NJohannes Weiner <hannes@cmpxchg.org> Acked-by: NVlastimil Babka <vbabka@suse.cz> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Rik van Riel <riel@surriel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mel Gorman 提交于
Patchset: "Move LRU page reclaim from zones to nodes v9" This series moves LRUs from the zones to the node. While this is a current rebase, the test results were based on mmotm as of June 23rd. Conceptually, this series is simple but there are a lot of details. Some of the broad motivations for this are; 1. The residency of a page partially depends on what zone the page was allocated from. This is partially combatted by the fair zone allocation policy but that is a partial solution that introduces overhead in the page allocator paths. 2. Currently, reclaim on node 0 behaves slightly different to node 1. For example, direct reclaim scans in zonelist order and reclaims even if the zone is over the high watermark regardless of the age of pages in that LRU. Kswapd on the other hand starts reclaim on the highest unbalanced zone. A difference in distribution of file/anon pages due to when they were allocated results can result in a difference in again. While the fair zone allocation policy mitigates some of the problems here, the page reclaim results on a multi-zone node will always be different to a single-zone node. it was scheduled on as a result. 3. kswapd and the page allocator scan zones in the opposite order to avoid interfering with each other but it's sensitive to timing. This mitigates the page allocator using pages that were allocated very recently in the ideal case but it's sensitive to timing. When kswapd is allocating from lower zones then it's great but during the rebalancing of the highest zone, the page allocator and kswapd interfere with each other. It's worse if the highest zone is small and difficult to balance. 4. slab shrinkers are node-based which makes it harder to identify the exact relationship between slab reclaim and LRU reclaim. The reason we have zone-based reclaim is that we used to have large highmem zones in common configurations and it was necessary to quickly find ZONE_NORMAL pages for reclaim. Today, this is much less of a concern as machines with lots of memory will (or should) use 64-bit kernels. Combinations of 32-bit hardware and 64-bit hardware are rare. Machines that do use highmem should have relatively low highmem:lowmem ratios than we worried about in the past. Conceptually, moving to node LRUs should be easier to understand. The page allocator plays fewer tricks to game reclaim and reclaim behaves similarly on all nodes. The series has been tested on a 16 core UMA machine and a 2-socket 48 core NUMA machine. The UMA results are presented in most cases as the NUMA machine behaved similarly. pagealloc --------- This is a microbenchmark that shows the benefit of removing the fair zone allocation policy. It was tested uip to order-4 but only orders 0 and 1 are shown as the other orders were comparable. 4.7.0-rc4 4.7.0-rc4 mmotm-20160623 nodelru-v9 Min total-odr0-1 490.00 ( 0.00%) 457.00 ( 6.73%) Min total-odr0-2 347.00 ( 0.00%) 329.00 ( 5.19%) Min total-odr0-4 288.00 ( 0.00%) 273.00 ( 5.21%) Min total-odr0-8 251.00 ( 0.00%) 239.00 ( 4.78%) Min total-odr0-16 234.00 ( 0.00%) 222.00 ( 5.13%) Min total-odr0-32 223.00 ( 0.00%) 211.00 ( 5.38%) Min total-odr0-64 217.00 ( 0.00%) 208.00 ( 4.15%) Min total-odr0-128 214.00 ( 0.00%) 204.00 ( 4.67%) Min total-odr0-256 250.00 ( 0.00%) 230.00 ( 8.00%) Min total-odr0-512 271.00 ( 0.00%) 269.00 ( 0.74%) Min total-odr0-1024 291.00 ( 0.00%) 282.00 ( 3.09%) Min total-odr0-2048 303.00 ( 0.00%) 296.00 ( 2.31%) Min total-odr0-4096 311.00 ( 0.00%) 309.00 ( 0.64%) Min total-odr0-8192 316.00 ( 0.00%) 314.00 ( 0.63%) Min total-odr0-16384 317.00 ( 0.00%) 315.00 ( 0.63%) Min total-odr1-1 742.00 ( 0.00%) 712.00 ( 4.04%) Min total-odr1-2 562.00 ( 0.00%) 530.00 ( 5.69%) Min total-odr1-4 457.00 ( 0.00%) 433.00 ( 5.25%) Min total-odr1-8 411.00 ( 0.00%) 381.00 ( 7.30%) Min total-odr1-16 381.00 ( 0.00%) 356.00 ( 6.56%) Min total-odr1-32 372.00 ( 0.00%) 346.00 ( 6.99%) Min total-odr1-64 372.00 ( 0.00%) 343.00 ( 7.80%) Min total-odr1-128 375.00 ( 0.00%) 351.00 ( 6.40%) Min total-odr1-256 379.00 ( 0.00%) 351.00 ( 7.39%) Min total-odr1-512 385.00 ( 0.00%) 355.00 ( 7.79%) Min total-odr1-1024 386.00 ( 0.00%) 358.00 ( 7.25%) Min total-odr1-2048 390.00 ( 0.00%) 362.00 ( 7.18%) Min total-odr1-4096 390.00 ( 0.00%) 362.00 ( 7.18%) Min total-odr1-8192 388.00 ( 0.00%) 363.00 ( 6.44%) This shows a steady improvement throughout. The primary benefit is from reduced system CPU usage which is obvious from the overall times; 4.7.0-rc4 4.7.0-rc4 mmotm-20160623nodelru-v8 User 189.19 191.80 System 2604.45 2533.56 Elapsed 2855.30 2786.39 The vmstats also showed that the fair zone allocation policy was definitely removed as can be seen here; 4.7.0-rc3 4.7.0-rc3 mmotm-20160623 nodelru-v8 DMA32 allocs 28794729769 0 Normal allocs 48432501431 77227309877 Movable allocs 0 0 tiobench on ext4 ---------------- tiobench is a benchmark that artifically benefits if old pages remain resident while new pages get reclaimed. The fair zone allocation policy mitigates this problem so pages age fairly. While the benchmark has problems, it is important that tiobench performance remains constant as it implies that page aging problems that the fair zone allocation policy fixes are not re-introduced. 4.7.0-rc4 4.7.0-rc4 mmotm-20160623 nodelru-v9 Min PotentialReadSpeed 89.65 ( 0.00%) 90.21 ( 0.62%) Min SeqRead-MB/sec-1 82.68 ( 0.00%) 82.01 ( -0.81%) Min SeqRead-MB/sec-2 72.76 ( 0.00%) 72.07 ( -0.95%) Min SeqRead-MB/sec-4 75.13 ( 0.00%) 74.92 ( -0.28%) Min SeqRead-MB/sec-8 64.91 ( 0.00%) 65.19 ( 0.43%) Min SeqRead-MB/sec-16 62.24 ( 0.00%) 62.22 ( -0.03%) Min RandRead-MB/sec-1 0.88 ( 0.00%) 0.88 ( 0.00%) Min RandRead-MB/sec-2 0.95 ( 0.00%) 0.92 ( -3.16%) Min RandRead-MB/sec-4 1.43 ( 0.00%) 1.34 ( -6.29%) Min RandRead-MB/sec-8 1.61 ( 0.00%) 1.60 ( -0.62%) Min RandRead-MB/sec-16 1.80 ( 0.00%) 1.90 ( 5.56%) Min SeqWrite-MB/sec-1 76.41 ( 0.00%) 76.85 ( 0.58%) Min SeqWrite-MB/sec-2 74.11 ( 0.00%) 73.54 ( -0.77%) Min SeqWrite-MB/sec-4 80.05 ( 0.00%) 80.13 ( 0.10%) Min SeqWrite-MB/sec-8 72.88 ( 0.00%) 73.20 ( 0.44%) Min SeqWrite-MB/sec-16 75.91 ( 0.00%) 76.44 ( 0.70%) Min RandWrite-MB/sec-1 1.18 ( 0.00%) 1.14 ( -3.39%) Min RandWrite-MB/sec-2 1.02 ( 0.00%) 1.03 ( 0.98%) Min RandWrite-MB/sec-4 1.05 ( 0.00%) 0.98 ( -6.67%) Min RandWrite-MB/sec-8 0.89 ( 0.00%) 0.92 ( 3.37%) Min RandWrite-MB/sec-16 0.92 ( 0.00%) 0.93 ( 1.09%) 4.7.0-rc4 4.7.0-rc4 mmotm-20160623 approx-v9 User 645.72 525.90 System 403.85 331.75 Elapsed 6795.36 6783.67 This shows that the series has little or not impact on tiobench which is desirable and a reduction in system CPU usage. It indicates that the fair zone allocation policy was removed in a manner that didn't reintroduce one class of page aging bug. There were only minor differences in overall reclaim activity 4.7.0-rc4 4.7.0-rc4 mmotm-20160623nodelru-v8 Minor Faults 645838 647465 Major Faults 573 640 Swap Ins 0 0 Swap Outs 0 0 DMA allocs 0 0 DMA32 allocs 46041453 44190646 Normal allocs 78053072 79887245 Movable allocs 0 0 Allocation stalls 24 67 Stall zone DMA 0 0 Stall zone DMA32 0 0 Stall zone Normal 0 2 Stall zone HighMem 0 0 Stall zone Movable 0 65 Direct pages scanned 10969 30609 Kswapd pages scanned 93375144 93492094 Kswapd pages reclaimed 93372243 93489370 Direct pages reclaimed 10969 30609 Kswapd efficiency 99% 99% Kswapd velocity 13741.015 13781.934 Direct efficiency 100% 100% Direct velocity 1.614 4.512 Percentage direct scans 0% 0% kswapd activity was roughly comparable. There were differences in direct reclaim activity but negligible in the context of the overall workload (velocity of 4 pages per second with the patches applied, 1.6 pages per second in the baseline kernel). pgbench read-only large configuration on ext4 --------------------------------------------- pgbench is a database benchmark that can be sensitive to page reclaim decisions. This also checks if removing the fair zone allocation policy is safe pgbench Transactions 4.7.0-rc4 4.7.0-rc4 mmotm-20160623 nodelru-v8 Hmean 1 188.26 ( 0.00%) 189.78 ( 0.81%) Hmean 5 330.66 ( 0.00%) 328.69 ( -0.59%) Hmean 12 370.32 ( 0.00%) 380.72 ( 2.81%) Hmean 21 368.89 ( 0.00%) 369.00 ( 0.03%) Hmean 30 382.14 ( 0.00%) 360.89 ( -5.56%) Hmean 32 428.87 ( 0.00%) 432.96 ( 0.95%) Negligible differences again. As with tiobench, overall reclaim activity was comparable. bonnie++ on ext4 ---------------- No interesting performance difference, negligible differences on reclaim stats. paralleldd on ext4 ------------------ This workload uses varying numbers of dd instances to read large amounts of data from disk. 4.7.0-rc3 4.7.0-rc3 mmotm-20160623 nodelru-v9 Amean Elapsd-1 186.04 ( 0.00%) 189.41 ( -1.82%) Amean Elapsd-3 192.27 ( 0.00%) 191.38 ( 0.46%) Amean Elapsd-5 185.21 ( 0.00%) 182.75 ( 1.33%) Amean Elapsd-7 183.71 ( 0.00%) 182.11 ( 0.87%) Amean Elapsd-12 180.96 ( 0.00%) 181.58 ( -0.35%) Amean Elapsd-16 181.36 ( 0.00%) 183.72 ( -1.30%) 4.7.0-rc4 4.7.0-rc4 mmotm-20160623 nodelru-v9 User 1548.01 1552.44 System 8609.71 8515.08 Elapsed 3587.10 3594.54 There is little or no change in performance but some drop in system CPU usage. 4.7.0-rc3 4.7.0-rc3 mmotm-20160623 nodelru-v9 Minor Faults 362662 367360 Major Faults 1204 1143 Swap Ins 22 0 Swap Outs 2855 1029 DMA allocs 0 0 DMA32 allocs 31409797 28837521 Normal allocs 46611853 49231282 Movable allocs 0 0 Direct pages scanned 0 0 Kswapd pages scanned 40845270 40869088 Kswapd pages reclaimed 40830976 40855294 Direct pages reclaimed 0 0 Kswapd efficiency 99% 99% Kswapd velocity 11386.711 11369.769 Direct efficiency 100% 100% Direct velocity 0.000 0.000 Percentage direct scans 0% 0% Page writes by reclaim 2855 1029 Page writes file 0 0 Page writes anon 2855 1029 Page reclaim immediate 771 1628 Sector Reads 293312636 293536360 Sector Writes 18213568 18186480 Page rescued immediate 0 0 Slabs scanned 128257 132747 Direct inode steals 181 56 Kswapd inode steals 59 1131 It basically shows that kswapd was active at roughly the same rate in both kernels. There was also comparable slab scanning activity and direct reclaim was avoided in both cases. There appears to be a large difference in numbers of inodes reclaimed but the workload has few active inodes and is likely a timing artifact. stutter ------- stutter simulates a simple workload. One part uses a lot of anonymous memory, a second measures mmap latency and a third copies a large file. The primary metric is checking for mmap latency. stutter 4.7.0-rc4 4.7.0-rc4 mmotm-20160623 nodelru-v8 Min mmap 16.6283 ( 0.00%) 13.4258 ( 19.26%) 1st-qrtle mmap 54.7570 ( 0.00%) 34.9121 ( 36.24%) 2nd-qrtle mmap 57.3163 ( 0.00%) 46.1147 ( 19.54%) 3rd-qrtle mmap 58.9976 ( 0.00%) 47.1882 ( 20.02%) Max-90% mmap 59.7433 ( 0.00%) 47.4453 ( 20.58%) Max-93% mmap 60.1298 ( 0.00%) 47.6037 ( 20.83%) Max-95% mmap 73.4112 ( 0.00%) 82.8719 (-12.89%) Max-99% mmap 92.8542 ( 0.00%) 88.8870 ( 4.27%) Max mmap 1440.6569 ( 0.00%) 121.4201 ( 91.57%) Mean mmap 59.3493 ( 0.00%) 42.2991 ( 28.73%) Best99%Mean mmap 57.2121 ( 0.00%) 41.8207 ( 26.90%) Best95%Mean mmap 55.9113 ( 0.00%) 39.9620 ( 28.53%) Best90%Mean mmap 55.6199 ( 0.00%) 39.3124 ( 29.32%) Best50%Mean mmap 53.2183 ( 0.00%) 33.1307 ( 37.75%) Best10%Mean mmap 45.9842 ( 0.00%) 20.4040 ( 55.63%) Best5%Mean mmap 43.2256 ( 0.00%) 17.9654 ( 58.44%) Best1%Mean mmap 32.9388 ( 0.00%) 16.6875 ( 49.34%) This shows a number of improvements with the worst-case outlier greatly improved. Some of the vmstats are interesting 4.7.0-rc4 4.7.0-rc4 mmotm-20160623nodelru-v8 Swap Ins 163 502 Swap Outs 0 0 DMA allocs 0 0 DMA32 allocs 618719206 1381662383 Normal allocs 891235743 564138421 Movable allocs 0 0 Allocation stalls 2603 1 Direct pages scanned 216787 2 Kswapd pages scanned 50719775 41778378 Kswapd pages reclaimed 41541765 41777639 Direct pages reclaimed 209159 0 Kswapd efficiency 81% 99% Kswapd velocity 16859.554 14329.059 Direct efficiency 96% 0% Direct velocity 72.061 0.001 Percentage direct scans 0% 0% Page writes by reclaim 6215049 0 Page writes file 6215049 0 Page writes anon 0 0 Page reclaim immediate 70673 90 Sector Reads 81940800 81680456 Sector Writes 100158984 98816036 Page rescued immediate 0 0 Slabs scanned 1366954 22683 While this is not guaranteed in all cases, this particular test showed a large reduction in direct reclaim activity. It's also worth noting that no page writes were issued from reclaim context. This series is not without its hazards. There are at least three areas that I'm concerned with even though I could not reproduce any problems in that area. 1. Reclaim/compaction is going to be affected because the amount of reclaim is no longer targetted at a specific zone. Compaction works on a per-zone basis so there is no guarantee that reclaiming a few THP's worth page pages will have a positive impact on compaction success rates. 2. The Slab/LRU reclaim ratio is affected because the frequency the shrinkers are called is now different. This may or may not be a problem but if it is, it'll be because shrinkers are not called enough and some balancing is required. 3. The anon/file reclaim ratio may be affected. Pages about to be dirtied are distributed between zones and the fair zone allocation policy used to do something very similar for anon. The distribution is now different but not necessarily in any way that matters but it's still worth bearing in mind. VM statistic counters for reclaim decisions are zone-based. If the kernel is to reclaim on a per-node basis then we need to track per-node statistics but there is no infrastructure for that. The most notable change is that the old node_page_state is renamed to sum_zone_node_page_state. The new node_page_state takes a pglist_data and uses per-node stats but none exist yet. There is some renaming such as vm_stat to vm_zone_stat and the addition of vm_node_stat and the renaming of mod_state to mod_zone_state. Otherwise, this is mostly a mechanical patch with no functional change. There is a lot of similarity between the node and zone helpers which is unfortunate but there was no obvious way of reusing the code and maintaining type safety. Link: http://lkml.kernel.org/r/1467970510-21195-2-git-send-email-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net> Acked-by: NJohannes Weiner <hannes@cmpxchg.org> Acked-by: NVlastimil Babka <vbabka@suse.cz> Cc: Rik van Riel <riel@surriel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> -
由 Shaohua Li 提交于
The md device might not have personality (for example, ddf raid array). The issue is introduced by 8430e7e0(md: disconnect device from personality before trying to remove it) Reported-by: Nkernel test robot <xiaolong.ye@intel.com> Signed-off-by: NShaohua Li <shli@fb.com>
-
- 28 7月, 2016 3 次提交
-
-
由 Dan Carpenter 提交于
We accidentally take the "port->lock" twice in a row. This old code was supposed to be deleted. Fixes: e58e241c ('sparc: serial: Clean up the locking for -rt') Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Theodore Ts'o 提交于
This fixes a crash on s390 with fake NUMA enabled. Reported-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Fixes: 1e7f583a ("random: make /dev/urandom scalable for silly userspace programs") Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
-
由 Linus Torvalds 提交于
Some of our "for_each_xyz()" macro constructs make gcc unhappy about lack of braces around if-statements inside or outside the loop, because the loop construct itself has a "if-then-else" statement inside of it. The resulting warnings look something like this: drivers/gpu/drm/i915/i915_debugfs.c: In function ‘i915_dump_lrc’: drivers/gpu/drm/i915/i915_debugfs.c:2103:6: warning: suggest explicit braces to avoid ambiguous ‘else’ [-Wparentheses] if (ctx != dev_priv->kernel_context) ^ even if the code itself is fine. Since the warning is fairly easy to avoid by adding a braces around the if-statement near the for_each_xyz() construct, do so, rather than disabling the otherwise potentially useful warning. (The if-then-else statements used in the "for_each_xyz()" constructs are designed to be inherently safe even with no braces, but in this case it's quite understandable that gcc isn't really able to tell that). This finally leaves the standard "allmodconfig" build with just a handful of remaining warnings, so new and valid warnings hopefully will stand out. Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 27 7月, 2016 18 次提交
-
-
由 Tony Camuso 提交于
Parameter trydefaults=1 causes the ipmi_init to initialize ipmi through the legacy port io space that was designated for ipmi. Architectures that do not map legacy port io can panic when trydefaults=1. Rather than implement build-time conditional exceptions for each architecture that does not map legacy port io, we have removed legacy port io from the driver. Parameter 'trydefaults' has been removed. Attempts to use it hereafter will evoke the "Unknown symbol in module, or unknown parameter" message. The patch was built against a number of architectures and tested for regressions and functionality on x86_64 and ARM64. Signed-off-by: NTony Camuso <tcamuso@redhat.com> Removed the config entry and the address source entry for default, since neither were used any more. Signed-off-by: NCorey Minyard <cminyard@mvista.com>
-
由 David S. Miller 提交于
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect': drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:759:22: warning: unused variable 'adev' [-Wunused-variable] Fixes: 8089a96f ("drivers: net: xgene: Add backward compatibility") Reported-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guilherme G. Piccoli 提交于
The be2net driver performs fw temperature queries on be_worker() routine, which is executed each second for each be_adapter. There is a frequency threshold to avoid fw query to happens at each call to be_worker(); instead, currently a fw query occurs once in 64 runs of the procedure. Nevertheless, this fw temperature query is invoked only for adapters which interface is up, so we can see I/O errors on read of hwmon counters from userspace (from tools like lm-sensors) in case we have adapters' functions which interface is down. This patch moves the fw query code to be invoked even if interface is down. No functional changes were introduced. Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by: NSathya Perla <sathya.perla@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Minchan Kim 提交于
Randy reported below build error. > In file included from ../include/linux/balloon_compaction.h:48:0, > from ../mm/balloon_compaction.c:11: > ../include/linux/compaction.h:237:51: warning: 'struct node' declared inside parameter list [enabled by default] > static inline int compaction_register_node(struct node *node) > ../include/linux/compaction.h:237:51: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default] > ../include/linux/compaction.h:242:54: warning: 'struct node' declared inside parameter list [enabled by default] > static inline void compaction_unregister_node(struct node *node) > It was caused by non-lru page migration which needs compaction.h but compaction.h doesn't include any header to be standalone. I think proper header for non-lru page migration is migrate.h rather than compaction.h because migrate.h has already headers needed to work non-lru page migration indirectly like isolate_mode_t, migrate_mode MIGRATEPAGE_SUCCESS. [akpm@linux-foundation.org: revert mm-balloon-use-general-non-lru-movable-page-feature-fix.patch temp fix] Link: http://lkml.kernel.org/r/20160610003304.GE29779@bboxSigned-off-by: NMinchan Kim <minchan@kernel.org> Reported-by: NRandy Dunlap <rdunlap@infradead.org> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Gioh Kim <gi-oh.kim@profitbricks.com> Cc: Rafael Aquini <aquini@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Provide a shmem_get_unmapped_area method in file_operations, called at mmap time to decide the mapping address. It could be conditional on CONFIG_TRANSPARENT_HUGEPAGE, but save #ifdefs in other places by making it unconditional. shmem_get_unmapped_area() first calls the usual mm->get_unmapped_area (which we treat as a black box, highly dependent on architecture and config and executable layout). Lots of conditions, and in most cases it just goes with the address that chose; but when our huge stars are rightly aligned, yet that did not provide a suitable address, go back to ask for a larger arena, within which to align the mapping suitably. There have to be some direct calls to shmem_get_unmapped_area(), not via the file_operations: because of the way shmem_zero_setup() is called to create a shmem object late in the mmap sequence, when MAP_SHARED is requested with MAP_ANONYMOUS or /dev/zero. Though this only matters when /proc/sys/vm/shmem_huge has been set. Link: http://lkml.kernel.org/r/1466021202-61880-29-git-send-email-kirill.shutemov@linux.intel.comSigned-off-by: NHugh Dickins <hughd@google.com> Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Kirill A. Shutemov 提交于
Let's add ShmemHugePages and ShmemPmdMapped fields into meminfo and smaps. It indicates how many times we allocate and map shmem THP. NR_ANON_TRANSPARENT_HUGEPAGES is renamed to NR_ANON_THPS. Link: http://lkml.kernel.org/r/1466021202-61880-27-git-send-email-kirill.shutemov@linux.intel.comSigned-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Kirill A. Shutemov 提交于
We always have vma->vm_mm around. Link: http://lkml.kernel.org/r/1466021202-61880-8-git-send-email-kirill.shutemov@linux.intel.comSigned-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Vlastimil Babka 提交于
I have noticed that frontswap.h first declares "frontswap_enabled" as extern bool variable, and then overrides it with "#define frontswap_enabled (1)" for CONFIG_FRONTSWAP=Y or (0) when disabled. The bool variable isn't actually instantiated anywhere. This all looks like an unfinished attempt to make frontswap_enabled reflect whether a backend is instantiated. But in the current state, all frontswap hooks call unconditionally into frontswap.c just to check if frontswap_ops is non-NULL. This should at least be checked inline, but we can further eliminate the overhead when CONFIG_FRONTSWAP is enabled and no backend registered, using a static key that is initially disabled, and gets enabled only upon first backend registration. Thus, checks for "frontswap_enabled" are replaced with "frontswap_enabled()" wrapping the static key check. There are two exceptions: - xen's selfballoon_process() was testing frontswap_enabled in code guarded by #ifdef CONFIG_FRONTSWAP, which was effectively always true when reachable. The patch just removes this check. Using frontswap_enabled() does not sound correct here, as this can be true even without xen's own backend being registered. - in SYSCALL_DEFINE2(swapon), change the check to IS_ENABLED(CONFIG_FRONTSWAP) as it seems the bitmap allocation cannot currently be postponed until a backend is registered. This means that frontswap will still have some memory overhead by being configured, but without a backend. After the patch, we can expect that some functions in frontswap.c are called only when frontswap_ops is non-NULL. Change the checks there to VM_BUG_ONs. While at it, convert other BUG_ONs to VM_BUG_ONs as frontswap has been stable for some time. [akpm@linux-foundation.org: coding-style fixes] Link: http://lkml.kernel.org/r/1463152235-9717-1-git-send-email-vbabka@suse.czSigned-off-by: NVlastimil Babka <vbabka@suse.cz> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Juergen Gross <jgross@suse.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Minchan Kim 提交于
Zsmalloc is ready for page migration so zram can use __GFP_MOVABLE from now on. I did test to see how it helps to make higher order pages. Test scenario is as follows. KVM guest, 1G memory, ext4 formated zram block device, for i in `seq 1 8`; do dd if=/dev/vda1 of=mnt/test$i.txt bs=128M count=1 & done wait `pidof dd` for i in `seq 1 2 8`; do rm -rf mnt/test$i.txt done fstrim -v mnt echo "init" cat /proc/buddyinfo echo "compaction" echo 1 > /proc/sys/vm/compact_memory cat /proc/buddyinfo old: init Node 0, zone DMA 208 120 51 41 11 0 0 0 0 0 0 Node 0, zone DMA32 16380 13777 9184 3805 789 54 3 0 0 0 0 compaction Node 0, zone DMA 132 82 40 39 16 2 1 0 0 0 0 Node 0, zone DMA32 5219 5526 4969 3455 1831 677 139 15 0 0 0 new: init Node 0, zone DMA 379 115 97 19 2 0 0 0 0 0 0 Node 0, zone DMA32 18891 16774 10862 3947 637 21 0 0 0 0 0 compaction Node 0, zone DMA 214 66 87 29 10 3 0 0 0 0 0 Node 0, zone DMA32 1612 3139 3154 2469 1745 990 384 94 7 0 0 As you can see, compaction made so many high-order pages. Yay! Link: http://lkml.kernel.org/r/1464736881-24886-13-git-send-email-minchan@kernel.orgSigned-off-by: NMinchan Kim <minchan@kernel.org> Reviewed-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> -
由 Minchan Kim 提交于
Now, VM has a feature to migrate non-lru movable pages so balloon doesn't need custom migration hooks in migrate.c and compaction.c. Instead, this patch implements the page->mapping->a_ops-> {isolate|migrate|putback} functions. With that, we could remove hooks for ballooning in general migration functions and make balloon compaction simple. [akpm@linux-foundation.org: compaction.h requires that the includer first include node.h] Link: http://lkml.kernel.org/r/1464736881-24886-4-git-send-email-minchan@kernel.orgSigned-off-by: NGioh Kim <gi-oh.kim@profitbricks.com> Signed-off-by: NMinchan Kim <minchan@kernel.org> Acked-by: NVlastimil Babka <vbabka@suse.cz> Cc: Rafael Aquini <aquini@redhat.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> -
由 Sergey Senozhatsky 提交于
We now allocate streams from CPU_UP hot-plug path, there are no context-dependent stream allocations anymore and we can schedule from zcomp_strm_alloc(). Use GFP_KERNEL directly and drop a gfp_t parameter. Link: http://lkml.kernel.org/r/20160531122017.2878-9-sergey.senozhatsky@gmail.comSigned-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: NMinchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Sergey Senozhatsky 提交于
Add "deflate", "lz4hc", "842" algorithms to the list of known compression backends. The real availability of those algorithms, however, depends on the corresponding CONFIG_CRYPTO_FOO config options. [sergey.senozhatsky@gmail.com: zram-add-more-compression-algorithms-v3] Link: http://lkml.kernel.org/r/20160604024902.11778-7-sergey.senozhatsky@gmail.com Link: http://lkml.kernel.org/r/20160531122017.2878-8-sergey.senozhatsky@gmail.comSigned-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: NMinchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Sergey Senozhatsky 提交于
Remove lzo/lz4 backends, we use crypto API now. [sergey.senozhatsky@gmail.com: zram-delete-custom-lzo-lz4-v3] Link: http://lkml.kernel.org/r/20160604024902.11778-6-sergey.senozhatsky@gmail.com Link: http://lkml.kernel.org/r/20160531122017.2878-7-sergey.senozhatsky@gmail.comSigned-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: NMinchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Sergey Senozhatsky 提交于
There is no way to get a string with all the crypto comp algorithms supported by the crypto comp engine, so we need to maintain our own backends list. At the same time we additionally need to use crypto_has_comp() to make sure that the user has requested a compression algorithm that is recognized by the crypto comp engine. Relying on /proc/crypto is not an options here, because it does not show not-yet-inserted compression modules. Example: modprobe zram cat /proc/crypto | grep -i lz4 modprobe lz4 cat /proc/crypto | grep -i lz4 name : lz4 driver : lz4-generic module : lz4 So the user can't tell exactly if the lz4 is really supported from /proc/crypto output, unless someone or something has loaded it. This patch also adds crypto_has_comp() to zcomp_available_show(). We store all the compression algorithms names in zcomp's `backends' array, regardless the CONFIG_CRYPTO_FOO configuration, but show only those that are also supported by crypto engine. This helps user to know the exact list of compression algorithms that can be used. Example: module lz4 is not loaded yet, but is supported by the crypto engine. /proc/crypto has no information on this module, while zram's `comp_algorithm' lists it: cat /proc/crypto | grep -i lz4 cat /sys/block/zram0/comp_algorithm [lzo] lz4 deflate lz4hc 842 We still use the `backends' array to determine if the requested compression backend is known to crypto api. This array, however, may not contain some entries, therefore as the last step we call crypto_has_comp() function which attempts to insmod the requested compression algorithm to determine if crypto api supports it. The advantage of this method is that now we permit the usage of out-of-tree crypto compression modules (implementing S/W or H/W compression). [sergey.senozhatsky@gmail.com: zram-use-crypto-api-to-check-alg-availability-v3] Link: http://lkml.kernel.org/r/20160604024902.11778-4-sergey.senozhatsky@gmail.com Link: http://lkml.kernel.org/r/20160531122017.2878-5-sergey.senozhatsky@gmail.comSigned-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: NMinchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Sergey Senozhatsky 提交于
We don't have an idle zstreams list anymore and our write path now works absolutely differently, preventing preemption during compression. This removes possibilities of read paths preempting writes at wrong places (which could badly affect the performance of both paths) and at the same time opens the door for a move from custom LZO/LZ4 compression backends implementation to a more generic one, using crypto compress API. Joonsoo Kim [1] attempted to do this a while ago, but faced with the need of introducing a new crypto API interface. The root cause was the fact that crypto API compression algorithms require a compression stream structure (in zram terminology) for both compression and decompression ops, while in reality only several of compression algorithms really need it. This resulted in a concept of context-less crypto API compression backends [2]. Both write and read paths, though, would have been executed with the preemption enabled, which in the worst case could have resulted in a decreased worst-case performance, e.g. consider the following case: CPU0 zram_write() spin_lock() take the last idle stream spin_unlock() << preempted >> zram_read() spin_lock() no idle streams spin_unlock() schedule() resuming zram_write compression() but it took me some time to realize that, and it took even longer to evolve zram and to make it ready for crypto API. The key turned out to be -- drop the idle streams list entirely. Without the idle streams list we are free to use compression algorithms that require compression stream for decompression (read), because streams are now placed in per-cpu data and each write path has to disable preemption for compression op, almost completely eliminating the aforementioned case (technically, we still have a small chance, because write path has a fast and a slow paths and the slow path is executed with the preemption enabled; but the frequency of failed fast path is too low). TEST ==== - 4 CPUs, x86_64 system - 3G zram, lzo - fio tests: read, randread, write, randwrite, rw, randrw test script [3] command: ZRAM_SIZE=3G LOG_SUFFIX=XXXX FIO_LOOPS=5 ./zram-fio-test.sh BASE PATCHED jobs1 READ: 2527.2MB/s 2482.7MB/s READ: 2102.7MB/s 2045.0MB/s WRITE: 1284.3MB/s 1324.3MB/s WRITE: 1080.7MB/s 1101.9MB/s READ: 430125KB/s 437498KB/s WRITE: 430538KB/s 437919KB/s READ: 399593KB/s 403987KB/s WRITE: 399910KB/s 404308KB/s jobs2 READ: 8133.5MB/s 7854.8MB/s READ: 7086.6MB/s 6912.8MB/s WRITE: 3177.2MB/s 3298.3MB/s WRITE: 2810.2MB/s 2871.4MB/s READ: 1017.6MB/s 1023.4MB/s WRITE: 1018.2MB/s 1023.1MB/s READ: 977836KB/s 984205KB/s WRITE: 979435KB/s 985814KB/s jobs3 READ: 13557MB/s 13391MB/s READ: 11876MB/s 11752MB/s WRITE: 4641.5MB/s 4682.1MB/s WRITE: 4164.9MB/s 4179.3MB/s READ: 1453.8MB/s 1455.1MB/s WRITE: 1455.1MB/s 1458.2MB/s READ: 1387.7MB/s 1395.7MB/s WRITE: 1386.1MB/s 1394.9MB/s jobs4 READ: 20271MB/s 20078MB/s READ: 18033MB/s 17928MB/s WRITE: 6176.8MB/s 6180.5MB/s WRITE: 5686.3MB/s 5705.3MB/s READ: 2009.4MB/s 2006.7MB/s WRITE: 2007.5MB/s 2004.9MB/s READ: 1929.7MB/s 1935.6MB/s WRITE: 1926.8MB/s 1932.6MB/s jobs5 READ: 18823MB/s 19024MB/s READ: 18968MB/s 19071MB/s WRITE: 6191.6MB/s 6372.1MB/s WRITE: 5818.7MB/s 5787.1MB/s READ: 2011.7MB/s 1981.3MB/s WRITE: 2011.4MB/s 1980.1MB/s READ: 1949.3MB/s 1935.7MB/s WRITE: 1940.4MB/s 1926.1MB/s jobs6 READ: 21870MB/s 21715MB/s READ: 19957MB/s 19879MB/s WRITE: 6528.4MB/s 6537.6MB/s WRITE: 6098.9MB/s 6073.6MB/s READ: 2048.6MB/s 2049.9MB/s WRITE: 2041.7MB/s 2042.9MB/s READ: 2013.4MB/s 1990.4MB/s WRITE: 2009.4MB/s 1986.5MB/s jobs7 READ: 21359MB/s 21124MB/s READ: 19746MB/s 19293MB/s WRITE: 6660.4MB/s 6518.8MB/s WRITE: 6211.6MB/s 6193.1MB/s READ: 2089.7MB/s 2080.6MB/s WRITE: 2085.8MB/s 2076.5MB/s READ: 2041.2MB/s 2052.5MB/s WRITE: 2037.5MB/s 2048.8MB/s jobs8 READ: 20477MB/s 19974MB/s READ: 18922MB/s 18576MB/s WRITE: 6851.9MB/s 6788.3MB/s WRITE: 6407.7MB/s 6347.5MB/s READ: 2134.8MB/s 2136.1MB/s WRITE: 2132.8MB/s 2134.4MB/s READ: 2074.2MB/s 2069.6MB/s WRITE: 2087.3MB/s 2082.4MB/s jobs9 READ: 19797MB/s 19994MB/s READ: 18806MB/s 18581MB/s WRITE: 6878.7MB/s 6822.7MB/s WRITE: 6456.8MB/s 6447.2MB/s READ: 2141.1MB/s 2154.7MB/s WRITE: 2144.4MB/s 2157.3MB/s READ: 2084.1MB/s 2085.1MB/s WRITE: 2091.5MB/s 2092.5MB/s jobs10 READ: 19794MB/s 19784MB/s READ: 18794MB/s 18745MB/s WRITE: 6984.4MB/s 6676.3MB/s WRITE: 6532.3MB/s 6342.7MB/s READ: 2150.6MB/s 2155.4MB/s WRITE: 2156.8MB/s 2161.5MB/s READ: 2106.4MB/s 2095.6MB/s WRITE: 2109.7MB/s 2098.4MB/s BASE PATCHED jobs1 perfstat stalled-cycles-frontend 102,480,595,419 ( 41.53%) 114,508,864,804 ( 46.92%) stalled-cycles-backend 51,941,417,832 ( 21.05%) 46,836,112,388 ( 19.19%) instructions 283,612,054,215 ( 1.15) 283,918,134,959 ( 1.16) branches 56,372,560,385 ( 724.923) 56,449,814,753 ( 733.766) branch-misses 374,826,000 ( 0.66%) 326,935,859 ( 0.58%) jobs2 perfstat stalled-cycles-frontend 155,142,745,777 ( 40.99%) 164,170,979,198 ( 43.82%) stalled-cycles-backend 70,813,866,387 ( 18.71%) 66,456,858,165 ( 17.74%) instructions 463,436,648,173 ( 1.22) 464,221,890,191 ( 1.24) branches 91,088,733,902 ( 760.088) 91,278,144,546 ( 769.133) branch-misses 504,460,363 ( 0.55%) 394,033,842 ( 0.43%) jobs3 perfstat stalled-cycles-frontend 201,300,397,212 ( 39.84%) 223,969,902,257 ( 44.44%) stalled-cycles-backend 87,712,593,974 ( 17.36%) 81,618,888,712 ( 16.19%) instructions 642,869,545,023 ( 1.27) 644,677,354,132 ( 1.28) branches 125,724,560,594 ( 690.682) 126,133,159,521 ( 694.542) branch-misses 527,941,798 ( 0.42%) 444,782,220 ( 0.35%) jobs4 perfstat stalled-cycles-frontend 246,701,197,429 ( 38.12%) 280,076,030,886 ( 43.29%) stalled-cycles-backend 119,050,341,112 ( 18.40%) 110,955,641,671 ( 17.15%) instructions 822,716,962,127 ( 1.27) 825,536,969,320 ( 1.28) branches 160,590,028,545 ( 688.614) 161,152,996,915 ( 691.068) branch-misses 650,295,287 ( 0.40%) 550,229,113 ( 0.34%) jobs5 perfstat stalled-cycles-frontend 298,958,462,516 ( 38.30%) 344,852,200,358 ( 44.16%) stalled-cycles-backend 137,558,742,122 ( 17.62%) 129,465,067,102 ( 16.58%) instructions 1,005,714,688,752 ( 1.29) 1,007,657,999,432 ( 1.29) branches 195,988,773,962 ( 697.730) 196,446,873,984 ( 700.319) branch-misses 695,818,940 ( 0.36%) 624,823,263 ( 0.32%) jobs6 perfstat stalled-cycles-frontend 334,497,602,856 ( 36.71%) 387,590,419,779 ( 42.38%) stalled-cycles-backend 163,539,365,335 ( 17.95%) 152,640,193,639 ( 16.69%) instructions 1,184,738,177,851 ( 1.30) 1,187,396,281,677 ( 1.30) branches 230,592,915,640 ( 702.902) 231,253,802,882 ( 702.356) branch-misses 747,934,786 ( 0.32%) 643,902,424 ( 0.28%) jobs7 perfstat stalled-cycles-frontend 396,724,684,187 ( 37.71%) 460,705,858,952 ( 43.84%) stalled-cycles-backend 188,096,616,496 ( 17.88%) 175,785,787,036 ( 16.73%) instructions 1,364,041,136,608 ( 1.30) 1,366,689,075,112 ( 1.30) branches 265,253,096,936 ( 700.078) 265,890,524,883 ( 702.839) branch-misses 784,991,589 ( 0.30%) 729,196,689 ( 0.27%) jobs8 perfstat stalled-cycles-frontend 440,248,299,870 ( 36.92%) 509,554,793,816 ( 42.46%) stalled-cycles-backend 222,575,930,616 ( 18.67%) 213,401,248,432 ( 17.78%) instructions 1,542,262,045,114 ( 1.29) 1,545,233,932,257 ( 1.29) branches 299,775,178,439 ( 697.666) 300,528,458,505 ( 694.769) branch-misses 847,496,084 ( 0.28%) 748,794,308 ( 0.25%) jobs9 perfstat stalled-cycles-frontend 506,269,882,480 ( 37.86%) 592,798,032,820 ( 44.43%) stalled-cycles-backend 253,192,498,861 ( 18.93%) 233,727,666,185 ( 17.52%) instructions 1,721,985,080,913 ( 1.29) 1,724,666,236,005 ( 1.29) branches 334,517,360,255 ( 694.134) 335,199,758,164 ( 697.131) branch-misses 873,496,730 ( 0.26%) 815,379,236 ( 0.24%) jobs10 perfstat stalled-cycles-frontend 549,063,363,749 ( 37.18%) 651,302,376,662 ( 43.61%) stalled-cycles-backend 281,680,986,810 ( 19.07%) 277,005,235,582 ( 18.55%) instructions 1,901,859,271,180 ( 1.29) 1,906,311,064,230 ( 1.28) branches 369,398,536,153 ( 694.004) 370,527,696,358 ( 688.409) branch-misses 967,929,335 ( 0.26%) 890,125,056 ( 0.24%) BASE PATCHED seconds elapsed 79.421641008 78.735285546 seconds elapsed 61.471246133 60.869085949 seconds elapsed 62.317058173 62.224188495 seconds elapsed 60.030739363 60.081102518 seconds elapsed 74.070398362 74.317582865 seconds elapsed 84.985953007 85.414364176 seconds elapsed 97.724553255 98.173311344 seconds elapsed 109.488066758 110.268399318 seconds elapsed 122.768189405 122.967164498 seconds elapsed 135.130035105 136.934770801 On my other system (8 x86_64 CPUs, short version of test results): BASE PATCHED seconds elapsed 19.518065994 19.806320662 seconds elapsed 15.172772749 15.594718291 seconds elapsed 13.820925970 13.821708564 seconds elapsed 13.293097816 14.585206405 seconds elapsed 16.207284118 16.064431606 seconds elapsed 17.958376158 17.771825767 seconds elapsed 19.478009164 19.602961508 seconds elapsed 21.347152811 21.352318709 seconds elapsed 24.478121126 24.171088735 seconds elapsed 26.865057442 26.767327618 So performance-wise the numbers are quite similar. Also update zcomp interface to be more aligned with the crypto API. [1] http://marc.info/?l=linux-kernel&m=144480832108927&w=2 [2] http://marc.info/?l=linux-kernel&m=145379613507518&w=2 [3] https://github.com/sergey-senozhatsky/zram-perf-test Link: http://lkml.kernel.org/r/20160531122017.2878-3-sergey.senozhatsky@gmail.comSigned-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Suggested-by: NMinchan Kim <minchan@kernel.org> Suggested-by: NJoonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by: NMinchan Kim <minchan@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> -
由 Sergey Senozhatsky 提交于
This has started as a 'add zlib support' work, but after some thinking I saw no blockers for a bigger change -- a switch to crypto API. We don't have an idle zstreams list anymore and our write path now works absolutely differently, preventing preemption during compression. This removes possibilities of read paths preempting writes at wrong places and opens the door for a move from custom LZO/LZ4 compression backends implementation to a more generic one, using crypto compress API. This patch set also eliminates the need of a new context-less crypto API interface, which was quite hard to sell, so we can move along faster. benchmarks: (x86_64, 4GB, zram-perf script) perf reported run-time fio (max jobs=3). I performed fio test with the increasing number of parallel jobs (max to 3) on a 3G zram device, using `static' data and the following crypto comp algorithms: 842, deflate, lz4, lz4hc, lzo the output was: - test running time (which can tell us what algorithms performs faster) and - zram mm_stat (which tells the compressed memory size, max used memory, etc). It's just for information. for example, LZ4HC has twice the running time of LZO, but the compressed memory size is: 23592960 vs 34603008 bytes. test-fio-zram-842 197.907655282 seconds time elapsed 201.623142884 seconds time elapsed 226.854291345 seconds time elapsed test-fio-zram-DEFLATE 253.259516155 seconds time elapsed 258.148563401 seconds time elapsed 290.251909365 seconds time elapsed test-fio-zram-LZ4 27.022598717 seconds time elapsed 29.580522717 seconds time elapsed 33.293463430 seconds time elapsed test-fio-zram-LZ4HC 56.393954615 seconds time elapsed 74.904659747 seconds time elapsed 101.940998564 seconds time elapsed test-fio-zram-LZO 28.155948075 seconds time elapsed 30.390036330 seconds time elapsed 34.455773159 seconds time elapsed zram mm_stat-s (max fio jobs=3) test-fio-zram-842 mm_stat (jobs1): 3221225472 673185792 690266112 0 690266112 0 0 mm_stat (jobs2): 3221225472 673185792 690266112 0 690266112 0 0 mm_stat (jobs3): 3221225472 673185792 690266112 0 690266112 0 0 test-fio-zram-DEFLATE mm_stat (jobs1): 3221225472 24379392 37761024 0 37761024 0 0 mm_stat (jobs2): 3221225472 24379392 37761024 0 37761024 0 0 mm_stat (jobs3): 3221225472 24379392 37761024 0 37761024 0 0 test-fio-zram-LZ4 mm_stat (jobs1): 3221225472 23592960 37761024 0 37761024 0 0 mm_stat (jobs2): 3221225472 23592960 37761024 0 37761024 0 0 mm_stat (jobs3): 3221225472 23592960 37761024 0 37761024 0 0 test-fio-zram-LZ4HC mm_stat (jobs1): 3221225472 23592960 37761024 0 37761024 0 0 mm_stat (jobs2): 3221225472 23592960 37761024 0 37761024 0 0 mm_stat (jobs3): 3221225472 23592960 37761024 0 37761024 0 0 test-fio-zram-LZO mm_stat (jobs1): 3221225472 34603008 50335744 0 50335744 0 0 mm_stat (jobs2): 3221225472 34603008 50335744 0 50335744 0 0 mm_stat (jobs3): 3221225472 34603008 50335744 0 50339840 0 0 This patch (of 8): We don't perform any zstream idle list lookup anymore, so zcomp_strm_find()/zcomp_strm_release() names are not representative. Rename to zcomp_stream_get()/zcomp_stream_put(). Link: http://lkml.kernel.org/r/20160531122017.2878-2-sergey.senozhatsky@gmail.comSigned-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: NMinchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> -
由 Vladimir Davydov 提交于
It's a part of oom context just like allocation order and nodemask, so let's move it to oom_control instead of passing it in the argument list. Link: http://lkml.kernel.org/r/40e03fd7aaf1f55c75d787128d6d17c5a71226c2.1464358556.git.vdavydov@virtuozzo.comSigned-off-by: NVladimir Davydov <vdavydov@virtuozzo.com> Acked-by: NMichal Hocko <mhocko@suse.com> Acked-by: NJohannes Weiner <hannes@cmpxchg.org> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: David Rientjes <rientjes@google.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Reza Arbab 提交于
Since zone_can_shift() is being used to validate the target zone during onlining, it should also be used to determine the content of valid_zones. Link: http://lkml.kernel.org/r/1462816419-4479-4-git-send-email-arbab@linux.vnet.ibm.comSigned-off-by: NReza Arbab <arbab@linux.vnet.ibm.com> Reviewd-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Daniel Kiper <daniel.kiper@oracle.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Andrew Banman <abanman@sgi.com> Cc: Chen Yucong <slaoub@gmail.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Zhang Zhen <zhenzhang.zhang@huawei.com> Cc: Shaohua Li <shaohua.li@intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-