There's no need to export the il_pci_suspend
and il_pci_resume functions since they're only
referenced from il_pm_ops. The latter can also
be defined using SIMPLE_DEV_PM_OPS instead of
open-coding it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Put power_level to ah_txpower struct with the rest tx power infos and
also rename it to txp_requested to make more sense.

v2 make sure we don't memset it to zero on reset
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By using cur_pwr on phy_init we re-use the power level previously set by the
driver, not the one we got from above.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rates[i] is unsigned but txp_offset can be negative for newer parts
with PDADC table. We cover the case when rates[i] + txp_offset > 63
but we must also cover the case when its < 0 or else rates[i] will overflow.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make sure we don't store the table offsets for min and cur power levels,
store the 0.25dB values instead. This way we don't clamp the tx power level
to max (because now cur_pwr holds the 0.25dB value, not the table offset) after
re-using cur_pwr on reset.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions and structs are not used in an other file and the
prototypes are in no header file, just make them static so the compiler
is able to optimize them better.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For the upcoming tpc changes, the driver needs
to provide sensible max output values for each
supported channel.

And while the eeprom always had a output_limit
table, which defines the upper limit for each
frequency and modulation, it was never really
useful for anything... until now.

Note: For anyone wondering about what your card
is calibrated for: check "iw list".
	* 2412 MHz [1] (18.0 dBm)
	* 2437 MHz [6] (19.0 dBm)
	[...]
	* 5180 MHz [36] (18.0 dBm)
	* 5260 MHz [52] (17.0 dBm) (radar detection)
	* 5680 MHz [136] (19.0 dBm) (radar detection)
(for a Dell Wireless 1450 USB Adapter)
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sequence counter will be sent to firmware via key_material
command.
Signed-off-by: NYing Luo <luoy@marvell.com>
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'cipher' and 'seq' coming from cfg80211 add_key handler will be
parsed in mwifiex_set_encode() to handle AES_CMAC cipher suite.
Signed-off-by: NYing Luo <luoy@marvell.com>
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This array was used for wapi_rxpn only. Now it will be used for
AES_CMAC as well. So make a generic name for it.
Signed-off-by: NYing Luo <luoy@marvell.com>
Signed-off-by: NStone Piao <piaoyun@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup TX/RX BA tables when AP receives deauthentication from
associated station. During BSS_IDLE event, all wmm queues, BA
streams created for AP interface are deleted.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for handling BA request and BA setup
events for AP interface.

RA list is marked as either 11n enabled or disabled from station's
capabilities in association request. BA setup is initiated only
after some specific number of packets for particular RA list are
transmitted.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for reception and decoding of AMSDU
aggregation frames for AP interface.
Patch also adds support for handling AMSDU aggregation event.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

1. Separate file for uAP RX handling.
2. If received packet is broadcast/multicast, send it to kernel
   as well as requeue it back to uAP TX queue.
3. If received packet is for associated STA (intra-BSS), requeue
   it back to uAP TX queue.
4. In all other cases (packets for AP or inter-BSS packets),
   pass packet to kernel to handle it accordingly.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After station is associated an entry would be added to station
list. This entry would have station specific information such as
11n support, AMSDU size. The entry would be deleted after
deauthentication. All station entries would be deleted during
BSS_IDLE event.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Route AP events handling to separate function defined in
uap_event.c.
AP specific event handling is removed from sta_event.c.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If HT IE is present in beacon_data of start_ap cfg80211 handler,
enable 11n flag in AP. Disable 11n flag when stop_ap handler is
called.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Earlier scan command was postponed by 20msec multiple times to give
preference to Tx traffic until we find empty wmm queue.

There is a corner case in which wmm queue becomes empty immediately
after processing the packet(before 20msec) and there may be next
packet coming after some time. In this case we should not resume scan
operation.

We will use new flag to check Tx traffic and resume scan operation
only if there is no traffic for 200msec.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As per recent patch "658f37b7 mwifiex: scan less channels..."
less channels are scanned per scan command in associated state.

Default number of channels per scan command for normal scan are
already 4, but those are 14 for SSID specific scan operation.

This code change in this patch is required for SSID specific scan.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do similar conversion for Tx packet header but it was missing
for Rx packet header. Without this fix, Rx packet header won't
be correctly parsed on big endian platform.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Padding arithmetic will always work for MSDUs provided first MSDU
ends on 4-byte boundary. Fixing it by making sure that all MSDU ends
on 4-byte boundary.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since commit: fb3c19bc, adding
extra padding to AMSDU is redundant since same is being performed at
mwifiex_11n_aggregate_pkt after forming the AMSDU packet. Fixing it
by removing it.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All MSDU subframes, except the first one in AMSDU, were being written
wrongly at the location of first MSDU frame. Fixing that by copying
the MSDU at skb->tail of AMSDU.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current indentation is off by one tab.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The first part of the power array is initialized in a loop
and the last two values are initialized separately. Extend
the loop to cover the last two items, and remove the separate
initialization.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch contains following modifications:

- Add mesh capabilities on fw.c to permit creation of mesh
  interfaces using this driver.

- Modify carl9170_set_operating_mode, to use AP-style beaconing
  with mesh interfaces.

- Allow beacon updates for NL80211_IFTYPE_MESH_POINT type in
  carl9170_handle_command_response.

- Add NL80211_IFTYPE_MESH_POINT case on carl9170_op_add_interfaces to
  support mesh/ap/sta virtual interface combinations.
Signed-off-by: NJavier Lopez <jlopex@cozybit.com>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

First of all, use PHY names instead of magic numbers. It should make
configuring kernel easier in case of not enabled PHY type support.
Secondly, always print info about PHY. This is really basic info about
hardware and quite important for the support level.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are more than 3 registers on new hardware. Host flags handling has
to be rewritten, as we can't use u128 type to handle all 5 regs.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers that load firmware from their probe routine have problems with the
latest versions of udev as they get timeouts while waiting for user
space to start. The problem is fixed by using request_firmware_nowait()
and delaying the start of mac80211 until the firmware is loaded.

To prevent the possibility of the driver being unloaded while the firmware
loading callback is still active, a completion queue entry is used.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of hard-coding almost the same functionality,
just use ieee80211_channel_to_frequency() directly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves the hci_conn check to begining of hci_le_conn_
complete_evt in order to improve code's readability and better
error handling.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch does a trivial code refactoring in hci_conn lookup in
hci_le_conn_complete_evt. It performs the hci_conn lookup at the
begining of the function since it is used by both flows (error
and success).
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>