IOP_RESET takes a long time to complete. If controller is in a state
where we can bring it back with init struct, send a DropIO sync command
instead.

 - If controller is faulted perform standard IOP_RESET in aac_srcv_init.

 - If controller is not faulted get adapter properties and extended
   properties.

 - Update the sa_firmware variable and determine if DropIO request is
   supported.

 - Issue DropIO request, and get the number of outstanding commands.

 - If all commands are complete with success (CT_OK), consider IOP_RESET
   is complete.

 - If any commands timeout, Perform the IOP_RESET.
Signed-off-by: NPrasad B Munirathnam <prasad.munirathnam@microsemi.com>
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDave Carroll <david.carroll@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The delay for the rescan worker needs to 10 seconds, missed the HZ in
there.

Fixes: a1367e4a (scsi: aacraid: Reschedule host scan in case of failure)
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update driver Version to 50877
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Earlier driver would scan throgh all supported buses and targets and add
devices that responded. It would add devices that were _hidden_ by the fw.
Driver would invalidate commands sent to _hidden_ devices via the
AAC_HIDE_DISK check.

Since the driver now adds only the devices that are supposed to be
exposed, this code can be removed.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove unused rescan variable.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add back the ability to scan for hotplug changes while eh was in progress.

Schedule a rescan for a later time in the eh recovery code and wait for
eh to complete in the rescan worker.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If the driver fails to retrieve information from the fw (could happen when
the fw is not fully in its senses), the driver does nothing and change is
not processed correctly by the driver

Schedule host rescan in case of failure. This is only for SAFW, since
the information retrieval failure will happen on SAFW devices.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver uses scsi_scan_host to add new devices in the driver init path,
which adds all the fw exposed devices. The drivers resorts to queue
command checks to block out commands to _hidden_ devices.

Use the hotplug handler code to add new devices during driver init and
other areas, this is only for safw. For ARC scsi_scan_host will still
apply.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently driver will attempt to process hotplug events concurrently based
on the FW interrupt.

Protect safw update function with a scan mutex.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added macros to loop through the MAX SUPPORTED Buses and Targets. This
will make the code a bit easier to read.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The hotplug handler code is duplicated for hba handling and container
handling.

Merged function to handle hba and container hot plug events into the
resolve luns functions. Added a bunch of helper functions to check the
validity of a given target and to check if bus, target is container
device.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Save the bmic information for each phy, so that it can processed in
target setup function.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove function call to process targets from the report phy luns function
and make it a function in its own right. This will help understand the
flow of the code.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add helper function to setup targets devices and create the base for the
upcoming patches
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rename variables and functions to make bmic identify, report phy luns
to make them consistent across code internal existing code bases
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Edit function that retrieves phy lun information to use common
bmic function
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

safw command submission is duplicated across many functions.

Move the safw submission code from bmic identify into its own function
for common use
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

"FIB_CONTEXT_FLAG_TIMEDOUT" flag is set in aac_eh_abort to indicate
command timeout. Using the same flag in reset handler causes the command
to time out and the I/Os were dropped.

Define a new flag "FIB_CONTEXT_FLAG_EH_RESET" to make sure I/O is
properly handled in eh_reset handler.

[mkp: tweaked commit message]
Signed-off-by: NPrasad B Munirathnam <prasad.munirathnam@microsemi.com>
Reviewed-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently the driver accepts two ways of requesting an initialization
reset on the adapter: by passing aac_reset_devices module parameter,
or the generic kernel parameter reset_devices.

It's working as intended...but if we end up reaching a scsi hang and
the scsi EH mechanism takes place, aacraid performs resets as part of
the scsi error recovery procedure. These EH routines might reinitialize
the device, and if we have provided some of the reset parameters in the
kernel command-line, we again perform an "initialization" reset.

So, to avoid this duplication of resets in case of scsi EH path, this
patch adds a field to aac_dev struct to keep per-adapter track of the
init reset request - once it's done, we set it to false and don't
proactively reset anymore in case of reinitializations.
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The logic for supporting large drives was previously tied to 4Kn support
for SmartIOC-2000. As SmartIOC-2000 does not support volumes using 4Kn
drives, use the intended option flag AAC_OPT_NEW_COMM_64 to determine
support for volumes greater than 2T.

Cc: <stable@vger.kernel.org>
Signed-off-by: NDave Carroll <david.carroll@microsemi.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We terminate the aac_get_name_resp on a byte that is outside the bounds
of the structure. Extend the return response by one byte to remove the
out of bounds reference.

Fixes: b836439f ("aacraid: 4KB sector support")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid Carroll <david.carroll@microsemi.com>
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NBart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

To correctly identify which fib has a scsi command callback this
patch implements a flag FIB_CONTEXT_FLAG_SCSI_CMD.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NRaghava Aditya Renukunta  <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update the driver version to 50834
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <david.carroll@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove reference to Series-9 HBA and created arc ctrl check function.
Signed-off-by: NPrasad B Munirathnam <prasad.munirathnam@microsemi.com>
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <david.carroll@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added function that waits with a timeout for the ctrl to be up and running
after triggering an IOP reset. Also removed 30 sec sleep as it is not
needed.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <david.carroll@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver can now trigger IOP reset with a single reset mask. Removed
code that retrieves a reset_mask from the firmware.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <david.carroll@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The qd for ARC Native disks is calculated by dividing the max IO 1024
by the number of disks or 256 which ever is lower. This causes poor
disk IO performance.

The fix is set the qd based on the type of disk (SAS - 64 and SATA -
32).
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <david.carroll@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

During a PCI error recovery, if aac_check_health() is not aware that a
PCI error happened and we have an offline PCI channel, it might trigger
some errors (like NULL pointer dereference) and inhibit the error
recovery process to complete.

This patch makes the health check procedure aware of PCI channel issues,
and in case of error recovery process, the function
aac_adapter_check_health() returns -1 and let the recovery process to
complete successfully. This patch was tested on upstream kernel
v4.11-rc5 in PowerPC ppc64le architecture with adapter 9005:028d
(VID:DID) - the error recovery procedure was able to recover fine.

Fixes: 5c63f7f7 ("aacraid: Added EEH support")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: NDave Carroll <david.carroll@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated driver version to 50792
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently  the adapter firmware does not save outstanding I/O's log
information  when an IOP reset is triggered. This is problematic when
trying to root cause and debug issues.

Fixed by adding sync command to trigger I/O log file save in the adapter
firmware before issuing an IOP reset.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After controller shutdown, all sync fibs time out due to not knowing
about the switch to INT-x mode

Fixed by replacing aac_src_access_devreg() to aac_set_intx_mode() call.

Cc: stable@vger.kernel.org
Fixes: 495c0217 (aacraid: MSI-x support)
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaced camel case with snake case for init supported options.
Suggested-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NDavid Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update the driver version to 50740
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added new copyright messages
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added a new ioctl interface to retrieve the host device information.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added a new ioctl interface to trigger an IOP or IWBR reset from ioctl.
Primary used by management utility to trigger resets.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added a new IWBR soft reset type, reworked the IOP reset interface for
a bit.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds support to retrieve the unique identifier data (VPD page
83 type3) for Logical drives created on SmartIOC 2000 products. In
addition  added a sysfs device structure to expose the id information.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added task management command support to abort any timed out commands
in case of a eh_abort call and to reset lun's in case of eh_reset call.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support to send direct pasthru srb commands from management utilty
to the  controller.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>