Instead of using HT info from beacon IEs, use HT info from
association response frame to update bandwidth in
cfg80211_get_channel handler.
Signed-off-by: NNachiket Kukade <kukaden@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Host sleep is cancelled in sdio resume() handler.
Cfg80211's resume handler is immediately called after
this. SYNC flag here ensures that host sleep handshake
gets completed and we have valid "adapter->nd_config"
before we report host wakeup reason in cfg80211's
resume handler.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for waking up the device on
finding better RSSI. Threshold RSSI value will be
configured by application.
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds code to report wakeup reason to cfg80211
when system is resumed.
Signed-off-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for wakeup when configured
network is detected.
Signed-off-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds informative messages in wake up on
magic packet, disconnect, pattern configuration paths.
Signed-off-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add sched scan support for mwifiex, include cfg80211
sched_scan_start/sched_scan_stop handler, corresponding bgscan
command path and event handler.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's been observed that driver's power state goes out
of sync with firmware in some corner cases. When this
happens, driver tries to download the data to firmware
assuming it's awake which causes Tx data timeout.

Main thread will process interrupt as soon as interrupt
handler fills 'int_status' variable.

This patch fixes the race issue by updating 'int_status'
at the end of mwifiex_interrupt_status().
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer pcie chipsets (8997 onwards) support MSIx. This
patch enables it.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch add 'verext' debugfs item, which can be used to
get detailed chip specific information from our firmware.

Examples:
echo "1" > /sys/kernel/debug/mwifiex/mlan0/verext
cat /sys/kernel/debug/mwifiex/mlan0/verext
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The port_open flag is not applicable for IBSS mode. IBSS data
path was broken when port_open flag was introduced.
This patch fixes the problem by correcting the checks.

Fixes: 5c894633 ("mwifiex: enable traffic only when port is open")
Signed-off-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Same chip is being used by WLAN as well as bluetooth
drivers. Each driver needs to check during initialisation
if firmware is already active or it needs to be freshly
downloaded. If one driver has started downloading the
firmware, other finds the winner flag as false.

mwifiex_check_fw_status() checks firmware status and also
check if WLAN is the winner for firmware downloading.

Once we detect that other interface is downloading
the firmware, we call this routine again with max
poll count to wait until firmware is ready.

This patch splits the routine to avoid checking
winner status unnecessarily multiple times and ensures
that correct messages are displayed to user.

Firmware status poll count is also increased to 150.
Signed-off-by: NChunfan Chen <jeffc@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Driver supports Tx status ack feature. When hostapd/
wpa_supplicant asks for ack status of an EAPOL/ACTION
frame, driver maintains a cloned skb for the packet
until TX_STATUS event is received from firmware.

Cloned skb queue gets flushed when connection is terminated
or driver is unloaded.

Let's reduce the queue size to avoid unnecessarily
keeping memory allocated when environment is busy.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch increase the priority for some critical
messages.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some critical messages are missed until "adapter->dev"
gets initialized in mwifiex_register_dev().
We will use pr_* print message instead of mwifiex_dbg at
those places to resolve the problem.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since kzalloc can be failed in memory pressure,
it needs to be handled, otherwise NULL dereference could be happened
Signed-off-by: NInsu Yun <wuninsu@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer pcie devices (8897 onwards) support MSI. This
patch enables it.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch ensures mwifiex_pcie_txbd_empty() does take care
of 8997 chipset.

Fixes: 6d85ef00 ("mwifiex: add support for 8997 chipset")
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch corrects some information in mwifiex_pcie_card_reg()
structure for 8997 chipset

Fixes: 6d85ef00 ("mwifiex: add support for 8997 chipset")
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

At some places, ie length is truncated from u16 to u8 while
storing it to driver's internal variable. This patch fixes
the problem.
Signed-off-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Device fails to connect to some AP's configured in WPA
security mode. Currently IE buffer parsing logic in driver
expects WPA IE to be present at the beginning of IE buffer.
Otherwise connection is failed with 'incompatible network
setting' error.

This patch fixes the problem by improving IE buffer parsing
logic.
Signed-off-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's better to use world if region code from EEPROM is
unidentied instead of forcing it to FCC
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This array contains list of supported region codes.
It is changed to make it aligned with region code
to country mapping table in driver.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Default gpio and gap is downloaded to firmware while
configuring host sleep for wake on disconnect. We may
have gpio and gap modified by user.

This patch fixes the problem.
Signed-off-by: Nchunfan chen <jeffc@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Sometimes AP sends TDLS setup response as AMSDU packet.
As driver doesn't parse it and update peer station's 11n
capability in this case, AMPDU doesn't get setup.

This patch calls mwifiex_process_tdls_action_frame() in
AMSDU Rx path to fix the problem.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This provides an option for user to power cycle the card.
It will be used to change the firmware without actually
rebooting the system.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

During AMSDU aggregation, we are already using timestamp
value of a first packet being aggregated. This patch removes
redundant ktime_get_real() call.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Block ACK action frames are dropped in driver. This error
is expected in this case. Let's lower the priority of this
message.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When hostapd is killed with Ctrl+C before cac get completed,
stop_ap handler will not be called, thus priv->wdev.cac_started
flag remains set.
Hostapd restart attempt will be failed in this case with device
busy error. This patch aborts cac in del_station handler to
handle this corner case.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Maximum supported wowlan pattern length has been increased
from 20 to 40.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Wildcard prefix bytes are ignored while downloading packet
pattern to firmware. As packet offset is not adjusted
accordingly firmware end up matching the pattern at wrong
offset. The packet offset is corrected in this patch.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is needed to support WAPI functionality.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes issues observed while starting 3 different
bss simultaneously, eg, 2 AP + 1 STA or 3 AP
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ap/station interface limit has been changed to allow
creating maximum 3 interfaces.
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

EU is not a valid country in db.txt file. Hence regulatory_hint
returns failure if EEPROM provides region code as 0x30. Let's
use FR for 0x30.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If device has already received country information from
EEPROM, we won't parse AP's country IE and download it to
firmware. We will also set regulatory flags to disable beacon
hints and ignore country IE.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Driver gets country information from EEPROM during
initialization. We will call regulatory_hint to update
current regulatory domain.
As by default world regulatory domain is selected by
cfg80211, country '00' from EEPROM is ignored.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's been observed that even if firmware returns an error
for a configuration command, we go ahead and start AP.

This patch changes the command type from async to sync
so that threads waits for command response and return
failure start AP.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Even if ADHOC start or join attempt is failed, these commands
are returned with success status by firmware. Actual connection
result is provided inside command response.

This patch parses the adhoc connection result and resets
connection state variables if connection is not successful.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>