Host map configuration instructs the interrupt controller to route interrupt
channels to FIQ or IRQ lines.  Currently, DA8xx family of devices leave these
registers at their reset-default values.

TNETV107X however does not have sane reset defaults, and therefore this
architecture needs to reconfigure the host-map such that channels 0 and 1
go to FIQ, and the remaining channels raise IRQs.

This patch adds an optional host map argument to cp_intc_init() for this.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

timer_init() programs timer64 hardware.  The module should ideally be brought
out of reset before this happens.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Preliminary modification prior to adding support for TNETV107X based on
ARM1176.  This change allows for CPUs other than ARM926T to be used for Davinci
derivative SoCs.  Existing devices (DA8x and DMx) operate unchanged.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The rtc-omap driver currently hardcodes the RTC wakeup capability
to be "not capable". While this seems to be true for existing OMAP1
boards which are not wired for this, the DA850/OMAP-L138 SoC, the
RTC can always be wake up source from its "deep sleep" mode.

This patch lets the wakeup capability to be set from platform data and
does not override the setting from the driver. For DA850/OMAP-L138, this
is done from arch/arm/mach-davinci/devices-da8xx.c:da8xx_register_rtc()

Note that this patch does not change the behavior on any existing OMAP1
board since the platform device registration sets the wakeup capability
to 0 by default.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This driver features:

* Alarm support.
* Periodic interrupt by using a timer include into the RTC module.
* The update interrupt is not supported by this RTC module.

This driver was tested on a DM365 EVM by using the rtc-test application
from the Documentation/rtc.txt.
Signed-off-by: NMiguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>

Currently, the ISR in the EDMA driver clears the pending interrupt for all
channels without regard to whether that channel has a registered callback
or not.

This causes problems for devices like DM355/DM365 where the multimedia
accelerator uses EDMA by polling on the interrupt pending bits of some of the
EDMA channels. Since these channels are actually allocated through the Linux
EDMA driver (by an out-of-kernel module), the same shadow region is used by
Linux and accelerator. There a race between the Linux ISR and the polling code
running on the accelerator on the IPR (interrupt pending register).

This patch fixes the issue by making the ISR clear the interrupts only for
those channels which have interrupt enabled. The channels which are allocated
for the purpose of being polled on by the accelerator will not have a callback
function provided and so will not have IER (interrupt enable register) bits set.

Tested on DM365 and OMAP-L137/L138 with audio and MMC/SD (as EDMA users).
Signed-off-by: NAnuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
CC: Archith John Bency <archith@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The merge for 2.6.34 brings in 8-bit support to the DaVinci MMC/SD driver.

This patch updates the platform data for DA830/OMAP-L137 EVM to use 8-wire
support available in the driver.
Signed-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

The DA830/OMAP-L137 EVM has GPIO based card detection logic, but the current
code does not use it.

Add support for GPIO based card detection to avoid reading the card to see
if a card is present or not.
Signed-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Cleanup usage of void pointers when using genirq.  genirq API
takes and returns void *, where this GPIO API is using those
as __iomem pointers.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

- Convert data/functions to static
- include headers for missing declarations
- pointer cleanups:  struct foo *__iomem f --> struct foo __iomem *f;
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  kgdb: don't needlessly skip PAGE_USER test for Fsl booke

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: add a shrinker to background inode reclaim

The bypassing of this test is a leftover from 2.4 vintage
kernels, and is no longer appropriate, or even used by KGDB.
Currently KGDB uses probe_kernel_write() for all access to
memory via the KGDB core, so it can simply be deleted.

This fixes CVE-2010-1446.

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: NWufei <fei.wu@windriver.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  exofs: Fix "add bdi backing to mount session" fall out
  fs: fs/super.c needs to include backing-dev.h for !CONFIG_BLOCK

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6061/1: PL061 GPIO: Bug fix - setting gpio for HIGH_LEVEL interrupt is not working.
  ARM: 5957/1: ARM: RealView SD/MMC Card detection and write-protect using GPIOLIB
  ARM: 6030/1: KS8695: enable console
  ARM: 6060/1: PL061 GPIO: Setting gpio val after changing direction to OUT.
  ARM: 6059/1: PL061 GPIO: Changing *_irq_chip_data with *_irq_data for real irqs.
  ARM: 6023/1: update bcmring_defconfig to latest version and fix build error
  ARM: fix build error in arch/arm/kernel/process.c

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/ps3: Update ps3_defconfig
  powerpc/ps3: Update platform maintainer
  powerpc/pseries: Flush lazy kernel mappings after unplug operations
  powerpc/numa: Add form 1 NUMA affinity
  powerpc/fsl-booke: Fix CONFIG_RELOCATABLE support on FSL Book-E ppc32
  powerpc: 2.6.34 update of defconfigs for embedded 6xx/7xxx, 8xx, 8xxx
  powerpc/mpc8xxx defconfigs - turn off SYSFS_DEPRECATED
  powerpc/83xx: configure SIL SATA driver in 83xx-wide defconfig
  powerpc/83xx: enable EPOLL syscall in defconfig
  powerpc/83xx: add RTC drivers in 83xx defconfig
  powerpc/fsl-cpm: Configure clock correctly for SCC
  powerpc/fsl_booke: Correct test for MMU_FTR_BIG_PHYS
  powerpc/85xx/86xx: Fix build w/ CONFIG_PCI=n

In current implementation of PL061, setting type of irq to HIGH_LEVEL is not
working. This patch fixes this bug.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On low memory boxes or those with highmem, kernel can OOM before the
background reclaims inodes via xfssyncd. Add a shrinker to run inode
reclaim so that it inode reclaim is expedited when memory is low.

This is more complex than it needs to be because the VM folk don't
want a context added to the shrinker infrastructure. Hence we need
to add a global list of XFS mount structures so the shrinker can
traverse them.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>

The patch: add bdi backing to mount session
	(b3d0ab7e)

Has a bug in the placement of the bdi member at
struct exofs_sb_info. The layout member must be kept
last.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

When CONFIG_BLOCK is set, it ends up getting backing-dev.h included.
But for !CONFIG_BLOCK, it isn't so lucky. The proper thing to do is
include <linux/backing-dev.h> directly from the file it's used from,
so do that.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  nfs: fix memory leak in nfs_get_sb with CONFIG_NFS_V4
  nfs: fix some issues in nfs41_proc_reclaim_complete()
  NFS: Ensure that nfs_wb_page() waits for Pg_writeback to clear
  NFS: Fix an unstable write data integrity race
  nfs: testing for null instead of ERR_PTR()
  NFS: rsize and wsize settings ignored on v4 mounts
  NFSv4: Don't attempt an atomic open if the file is a mountpoint
  SUNRPC: Fix a bug in rpcauth_prune_expired

The pktcdvd driver uses proper locking and does not need the BKL in the
ioctl and llseek functions of the character device, so kill both.

Moving the compat_ioctl handling from common code into the driver itself
fixes build problems when CONFIG_BLOCK is disabled.
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit b3d0ab7e ("exofs: add bdi backing
to mount session") has a bug in the placement of the bdi member at
struct exofs_sb_info.  The layout member must be kept last.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
  x86: Disable large pages on CPUs with Atom erratum AAE44
  x86-64: Clear a 64-bit FS/GS base on fork if selector is nonzero
  x86, mrst: Conditionally register cpu hotplug notifier for apbt

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  x86/PCI: compute Address Space length rather than using _LEN
  x86/PCI: never allocate PCI MMIO resources below BIOS_END

If dentry found stale happens to be a root of disconnected tree, we
can't d_drop() it; its d_hash is actually part of s_anon and d_drop()
would simply hide it from shrink_dcache_for_umount(), leading to
all sorts of fun, including busy inodes on umount and oopsen after
that.

Bug had been there since at least 2006 (commit c636eb already has it),
so it's definitely -stable fodder.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The switch to using GPIOLIB broke the sd/mmc card detection on the
RealView development boards if GPIO_PL061 was not selected.
This patch selects GPIO_PL061 if GPIOLIB is selected.
The sense of the return value from mmc_status has also changed
and is corrected.
Signed-off-by: NColin Tuckley <colin.tuckley@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: fix enabling regulator issue on max8925

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
  sfc: Change falcon_probe_board() to fail for unsupported boards
  sfc: Always close net device at the end of a disabling reset
  sfc: Wait at most 10ms for the MC to finish reading out MAC statistics
  sctp: Fix oops when sending queued ASCONF chunks
  sctp: fix to calc the INIT/INIT-ACK chunk length correctly is set
  sctp: per_cpu variables should be in bh_disabled section
  sctp: fix potential reference of a freed pointer
  sctp: avoid irq lock inversion while call sk->sk_data_ready()
  Revert "tcp: bind() fix when many ports are bound"
  net/usb: add sierra_net.c driver
  cdc_ether: fix autosuspend for mbm devices
  bluetooth: handle l2cap_create_connless_pdu() errors
  gianfar: Wait for both RX and TX to stop
  ipheth: potential null dereferences on error path
  smc91c92_cs: spin_unlock_irqrestore before calling smc_interrupt()
  drivers/usb/net/kaweth.c: add device "Allied Telesyn AT-USB10 USB Ethernet Adapter"
  bnx2: Update version to 2.0.9.
  bnx2: Prevent "scheduling while atomic" warning with cnic, bonding and vlan.
  bnx2: Fix lost MSI-X problem on 5709 NICs.
  cxgb3: Wait longer for control packets on initialization
  ...

The driver needs specific PHY and board support code for each SFC4000
board; there is no point trying to continue if it is missing.
Currently unsupported boards can trigger an 'oops'.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a regression introduced by commit
eb9f6744 "sfc: Implement ethtool
reset operation".
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original code would wait indefinitely if MAC stats DMA failed.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we finish processing ASCONF_ACK chunk, we try to send
the next queued ASCONF.  This action runs the sctp state
machine recursively and it's not prepared to do so.

kernel BUG at kernel/timer.c:790!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/module/ipv6/initstate
Modules linked in: sha256_generic sctp libcrc32c ipv6 dm_multipath
uinput 8139too i2c_piix4 8139cp mii i2c_core pcspkr virtio_net joydev
floppy virtio_blk virtio_pci [last unloaded: scsi_wait_scan]

Pid: 0, comm: swapper Not tainted 2.6.34-rc4 #15 /Bochs
EIP: 0060:[<c044a2ef>] EFLAGS: 00010286 CPU: 0
EIP is at add_timer+0xd/0x1b
EAX: cecbab14 EBX: 000000f0 ECX: c0957b1c EDX: 03595cf4
ESI: cecba800 EDI: cf276f00 EBP: c0957aa0 ESP: c0957aa0
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process swapper (pid: 0, ti=c0956000 task=c0988ba0 task.ti=c0956000)
Stack:
 c0957ae0 d1851214 c0ab62e4 c0ab5f26 0500ffff 00000004 00000005 00000004
<0> 00000000 d18694fd 00000004 1666b892 cecba800 cecba800 c0957b14
00000004
<0> c0957b94 d1851b11 ceda8b00 cecba800 cf276f00 00000001 c0957b14
000000d0
Call Trace:
 [<d1851214>] ? sctp_side_effects+0x607/0xdfc [sctp]
 [<d1851b11>] ? sctp_do_sm+0x108/0x159 [sctp]
 [<d1863386>] ? sctp_pname+0x0/0x1d [sctp]
 [<d1861a56>] ? sctp_primitive_ASCONF+0x36/0x3b [sctp]
 [<d185657c>] ? sctp_process_asconf_ack+0x2a4/0x2d3 [sctp]
 [<d184e35c>] ? sctp_sf_do_asconf_ack+0x1dd/0x2b4 [sctp]
 [<d1851ac1>] ? sctp_do_sm+0xb8/0x159 [sctp]
 [<d1863334>] ? sctp_cname+0x0/0x52 [sctp]
 [<d1854377>] ? sctp_assoc_bh_rcv+0xac/0xe1 [sctp]
 [<d1858f0f>] ? sctp_inq_push+0x2d/0x30 [sctp]
 [<d186329d>] ? sctp_rcv+0x797/0x82e [sctp]
Tested-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NYuansong Qiao <ysqiao@research.ait.ie>
Signed-off-by: NShuaijun Zhang <szhang@research.ait.ie>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When calculating the INIT/INIT-ACK chunk length, we should not
only account the length of parameters, but also the parameters
zero padding length, such as AUTH HMACS parameter and CHUNKS
parameter. Without the parameters zero padding length we may get
following oops.

skb_over_panic: text:ce2068d2 len:130 put:6 head:cac3fe00 data:cac3fe00 tail:0xcac3fe82 end:0xcac3fe80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:127!
invalid opcode: 0000 [#2] SMP
last sysfs file: /sys/module/aes_generic/initstate
Modules linked in: authenc ......

Pid: 4102, comm: sctp_darn Tainted: G      D    2.6.34-rc2 #6
EIP: 0060:[<c0607630>] EFLAGS: 00010282 CPU: 0
EIP is at skb_over_panic+0x37/0x3e
EAX: 00000078 EBX: c07c024b ECX: c07c02b9 EDX: cb607b78
ESI: 00000000 EDI: cac3fe7a EBP: 00000002 ESP: cb607b74
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process sctp_darn (pid: 4102, ti=cb607000 task=cabdc990 task.ti=cb607000)
Stack:
 c07c02b9 ce2068d2 00000082 00000006 cac3fe00 cac3fe00 cac3fe82 cac3fe80
<0> c07c024b cac3fe7c cac3fe7a c0608dec ca986e80 ce2068d2 00000006 0000007a
<0> cb8120ca ca986e80 cb812000 00000003 cb8120c4 ce208a25 cb8120ca cadd9400
Call Trace:
 [<ce2068d2>] ? sctp_addto_chunk+0x45/0x85 [sctp]
 [<c0608dec>] ? skb_put+0x2e/0x32
 [<ce2068d2>] ? sctp_addto_chunk+0x45/0x85 [sctp]
 [<ce208a25>] ? sctp_make_init+0x279/0x28c [sctp]
 [<c0686a92>] ? apic_timer_interrupt+0x2a/0x30
 [<ce1fdc0b>] ? sctp_sf_do_prm_asoc+0x2b/0x7b [sctp]
 [<ce202823>] ? sctp_do_sm+0xa0/0x14a [sctp]
 [<ce2133b9>] ? sctp_pname+0x0/0x14 [sctp]
 [<ce211d72>] ? sctp_primitive_ASSOCIATE+0x2b/0x31 [sctp]
 [<ce20f3cf>] ? sctp_sendmsg+0x7a0/0x9eb [sctp]
 [<c064eb1e>] ? inet_sendmsg+0x3b/0x43
 [<c04244b7>] ? task_tick_fair+0x2d/0xd9
 [<c06031e1>] ? sock_sendmsg+0xa7/0xc1
 [<c0416afe>] ? smp_apic_timer_interrupt+0x6b/0x75
 [<c0425123>] ? dequeue_task_fair+0x34/0x19b
 [<c0446abb>] ? sched_clock_local+0x17/0x11e
 [<c052ea87>] ? _copy_from_user+0x2b/0x10c
 [<c060ab3a>] ? verify_iovec+0x3c/0x6a
 [<c06035ca>] ? sys_sendmsg+0x186/0x1e2
 [<c042176b>] ? __wake_up_common+0x34/0x5b
 [<c04240c2>] ? __wake_up+0x2c/0x3b
 [<c057e35c>] ? tty_wakeup+0x43/0x47
 [<c04430f2>] ? remove_wait_queue+0x16/0x24
 [<c0580c94>] ? n_tty_read+0x5b8/0x65e
 [<c042be02>] ? default_wake_function+0x0/0x8
 [<c0604e0e>] ? sys_socketcall+0x17f/0x1cd
 [<c040264c>] ? sysenter_do_call+0x12/0x22
Code: 0f 45 de 53 ff b0 98 00 00 00 ff b0 94 ......
EIP: [<c0607630>] skb_over_panic+0x37/0x3e SS:ESP 0068:cb607b74

To reproduce:

# modprobe sctp
# echo 1 > /proc/sys/net/sctp/addip_enable
# echo 1 > /proc/sys/net/sctp/auth_enable
# sctp_test -H 3ffe:501:ffff:100:20c:29ff:fe4d:f37e -P 800 -l
# sctp_darn -H 3ffe:501:ffff:100:20c:29ff:fe4d:f37e -P 900 -h 192.168.0.21 -p 800 -I -s -t
sctp_darn ready to send...
3ffe:501:ffff:100:20c:29ff:fe4d:f37e:900-192.168.0.21:800 Interactive mode> bindx-add=192.168.0.21
3ffe:501:ffff:100:20c:29ff:fe4d:f37e:900-192.168.0.21:800 Interactive mode> bindx-add=192.168.1.21
3ffe:501:ffff:100:20c:29ff:fe4d:f37e:900-192.168.0.21:800 Interactive mode> snd=10

------------------------------------------------------------------
eth0 has addresses: 3ffe:501:ffff:100:20c:29ff:fe4d:f37e and 192.168.0.21
eth1 has addresses: 192.168.1.21
------------------------------------------------------------------
Reported-by: NGeorge Cheimonidis <gchimon@gmail.com>
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the change of the atomics to percpu variables, we now
have to disable BH in process context when touching percpu variables.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sctp attempts to update an assocition, it removes any
addresses that were not in the updated INITs.  However, the loop
may attempt to refrence a transport with address after removing it.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sk->sk_data_ready() of sctp socket can be called from both BH and non-BH
contexts, but the default sk->sk_data_ready(), sock_def_readable(), can
not be used in this case. Therefore, we have to make a new function
sctp_data_ready() to grab sk->sk_data_ready() with BH disabling.

=========================================================
[ INFO: possible irq lock inversion dependency detected ]
2.6.33-rc6 #129
---------------------------------------------------------
sctp_darn/1517 just changed the state of lock:
 (clock-AF_INET){++.?..}, at: [<c06aab60>] sock_def_readable+0x20/0x80
but this lock took another, SOFTIRQ-unsafe lock in the past:
 (slock-AF_INET){+.-...}

and interrupts could create inverse lock ordering between them.

other info that might help us debug this:
1 lock held by sctp_darn/1517:
 #0:  (sk_lock-AF_INET){+.+.+.}, at: [<cdfe363d>] sctp_sendmsg+0x23d/0xc00 [sctp]
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts two commits:

fda48a0d
tcp: bind() fix when many ports are bound

and a follow-on fix for it:

6443bb1f
ipv6: Fix inet6_csk_bind_conflict()

It causes problems with binding listening sockets when time-wait
sockets from a previous instance still are alive.

It's too late to keep fiddling with this so late in the -rc
series, and we'll deal with it in net-next-2.6 instead.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With CONFIG_NFS_V4 and data version 4, nfs_get_sb will allocate memory for
export_path in nfs4_validate_text_mount_data, so we need to free it then.
This is addressed in following kmemleak report:

unreferenced object 0xffff88016bf48a50 (size 16):
  comm "mount.nfs", pid 22567, jiffies 4651574704 (age 175471.200s)
  hex dump (first 16 bytes):
    2f 6f 70 74 2f 77 6f 72 6b 00 6b 6b 6b 6b 6b a5  /opt/work.kkkkk.
  backtrace:
    [<ffffffff814b34f9>] kmemleak_alloc+0x60/0xa7
    [<ffffffff81102c76>] kmemleak_alloc_recursive.clone.5+0x1b/0x1d
    [<ffffffff811046b3>] __kmalloc_track_caller+0x18f/0x1b7
    [<ffffffff810e1b08>] kstrndup+0x37/0x54
    [<ffffffffa0336971>] nfs_parse_devname+0x152/0x204 [nfs]
    [<ffffffffa0336af3>] nfs4_validate_text_mount_data+0xd0/0xdc [nfs]
    [<ffffffffa0338deb>] nfs_get_sb+0x325/0x736 [nfs]
    [<ffffffff81113671>] vfs_kern_mount+0xbd/0x17c
    [<ffffffff81113798>] do_kern_mount+0x4d/0xed
    [<ffffffff81129a87>] do_mount+0x787/0x7fe
    [<ffffffff81129b86>] sys_mount+0x88/0xc2
    [<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
Signed-off-by: NXiaotian Feng <dfeng@redhat.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Benny Halevy <bhalevy@panasas.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andy Adamson <andros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>