Signed-off-by: NAdam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

I ran into this issue while debugging an early boot problem. The system
hit a BUG_ON() but report bug failed to print the line number and file
name. The reason being that the system was running in real mode and
report_bug() searches for addresses in the PAGE_OFFSET+ region.
Suggested-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add a cputable entry for POWER9.  More code is required to actually
boot and run on a POWER9 but this gets the base piece in which we can
start building on.

Copies over from POWER8 except for:
- Adds a new CPU_FTR_ARCH_300 bit to start hanging new architecture
   features from (in subsequent patches).
- Advertises new user features bits PPC_FEATURE2_ARCH_3_00 &
  HAS_IEEE128 when on POWER9.
- Drops CPU_FTR_SUBCORE.
- Drops PMU code and machine check.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use defines for literals __init_tlb_power[78] rather than hand coding
them.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

During error recovery, the device could be removed as part of the
partial hotplug. The criterion used to come with partial hotplug
is: if the device driver provides error_detected(), slot_reset()
and resume() callbacks, it's immune from hotplug. Otherwise,
it's going to experience partial hotplug during EEH recovery. But
the criterion isn't correct enough: mlx4_core driver for Mellanox
adapters provides error_detected(), slot_reset() callbacks, but
resume() isn't there. Those Mellanox adapters won't be to involved
in the partial hotplug.

This fixes the criterion to a practical one: adpater with driver
that provides error_detected(), slot_reset() will be immune from
partial hotplug. resume() isn't mandatory.

Fixes: f2da4ccf ("powerpc/eeh: More relaxed hotplug criterion")
Cc: stable@vger.kernel.org #v4.4+
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

I spent some time trying to use kgdb and debugged my inability to
resume from kgdb_handle_breakpoint(). NIP is not incremented
and that leads to a loop in the debugger.

I've tested this lightly on a virtual instance with KDB enabled.
After the patch, I am able to get the "go" command to work as
expected.
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When PE is created, its primary bus is cached to pe->bus. At later
point, the cached primary bus is returned from eeh_pe_bus_get().
However, we could get stale cached primary bus and run into kernel
crash in one case: full hotplug as part of fenced PHB error recovery
releases all PCI busses under the PHB at unplugging time and recreate
them at plugging time. pe->bus is still dereferencing the PCI bus
that was released.

This adds another PE flag (EEH_PE_PRI_BUS) to represent the validity
of pe->bus. pe->bus is updated when its first child EEH device is
online and the flag is set. Before unplugging in full hotplug for
error recovery, the flag is cleared.

Fixes: 8cdb2833 ("powerpc/eeh: Trace PCI bus from PE")
Cc: stable@vger.kernel.org #v3.11+
Reported-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: NPradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The comment block above pcibios_set_pcie_reset_state() incorrectly refers
to pcibios_set_pcie_slot_reset(). Fix the comment accordingly.
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Since binutils 2.26 BFD is doing suffix merging on STRTAB sections.  But
dedotify modifies the symbol names in place, which can also modify
unrelated symbols with a name that matches a suffix of a dotted name.  To
remove the leading dot of a symbol name we can just increment the pointer
into the STRTAB section instead.

Backport to all stables to avoid breakage when people update their
binutils - mpe.

Cc: stable@vger.kernel.org
Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In eeh_pe_loc_get(), the PE location code is retrieved from the
"ibm,loc-code" property of the device node for the bridge of the
PE's primary bus. It's not correct because the property indicates
the parent PE's location code.

This reads the correct PE location code from "ibm,io-base-loc-code"
or "ibm,slot-location-code" property of PE parent bus's device node.

Cc: stable@vger.kernel.org # v3.16+
Fixes: 357b2f3d ("powerpc/eeh: Dump PE location code")
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

PowerPC64 uses the symbol .TOC. much as other targets use
_GLOBAL_OFFSET_TABLE_. It identifies the value of the GOT pointer (or in
powerpc parlance, the TOC pointer). Global offset tables are generally
local to an executable or shared library, or in the kernel, module. Thus
it does not make sense for a module to resolve a relocation against
.TOC. to the kernel's .TOC. value. A module has its own .TOC., and
indeed the powerpc64 module relocation processing ignores the kernel
value of .TOC. and instead calculates a module-local value.

This patch removes code involved in exporting the kernel .TOC., tweaks
modpost to ignore an undefined .TOC., and the module loader to twiddle
the section symbol so that .TOC. isn't seen as undefined.

Note that if the kernel was compiled with -msingle-pic-base then ELFv2
would not have function global entry code setting up r2. In that case
the module call stubs would need to be modified to set up r2 using the
kernel .TOC. value, requiring some of this code to be reinstated.

mpe: Furthermore a change in binutils master (not yet released) causes
the current way we handle the TOC to no longer work when building with
MODVERSIONS=y and RELOCATABLE=n. The symptom is that modules can not be
loaded due to there being no version found for TOC.

Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: NAlan Modra <amodra@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This hooks up UBSAN support for PowerPC.

So far it's found some interesting cases where we don't properly sanitise
input to shifts, including one in our futex handling.  Nothing critical,
but interesting and worth fixing.

[valentinrothberg@gmail.com: arch/powerpc/Kconfig: fix typo in select statement]
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NValentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The four cpumasks cpu_{possible,online,present,active}_bits are exposed
readonly via the corresponding const variables cpu_xyz_mask.  But they are
also accessible for arbitrary writing via the exposed functions
set_cpu_xyz.  There's quite a bit of code throughout the kernel which
iterates over or otherwise accesses these bitmaps, and having the access
go via the cpu_xyz_mask variables is nowadays [1] simply a useless
indirection.

It may be that any problem in CS can be solved by an extra level of
indirection, but that doesn't mean every extra indirection solves a
problem.  In this case, it even necessitates some minor ugliness (see
4/6).

Patch 1/6 is new in v2, and fixes a build failure on ppc by renaming a
struct member, to avoid problems when the identifier cpu_online_mask
becomes a macro later in the series.  The next four patches eliminate the
cpu_xyz_mask variables by simply exposing the actual bitmaps, after
renaming them to discourage direct access - that still happens through
cpu_xyz_mask, which are now simply macros with the same type and value as
they used to have.

After that, there's no longer any reason to have the setter functions be
out-of-line: The boolean parameter is almost always a literal true or
false, so by making them static inlines they will usually compile to one
or two instructions.

For a defconfig build on x86_64, bloat-o-meter says we save ~3000 bytes.
We also save a little stack (stackdelta says 127 functions have a 16 byte
smaller stack frame, while two grow by that amount).  Mostly because, when
iterating over the mask, gcc typically loads the value of cpu_xyz_mask
into a callee-saved register and from there into %rdi before each
find_next_bit call - now it can just load the appropriate immediate
address into %rdi before each call.

[1] See Rusty's kind explanation
http://thread.gmane.org/gmane.linux.kernel/2047078/focus=2047722 for
some historic context.

This patch (of 6):

As preparation for eliminating the indirect access to the various global
cpu_*_bits bitmaps via the pointer variables cpu_*_mask, rename the
cpu_online_mask member of struct fadump_crash_info_header to simply
online_mask, thus allowing cpu_online_mask to become a macro.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

GCC 6 will include changes to generated code with -mcmodel=large,
which is used to build kernel modules on powerpc64le.  This was
necessary because the large model is supposed to allow arbitrary
sizes and locations of the code and data sections, but the ELFv2
global entry point prolog still made the unconditional assumption
that the TOC associated with any particular function can be found
within 2 GB of the function entry point:

func:
	addis r2,r12,(.TOC.-func)@ha
	addi  r2,r2,(.TOC.-func)@l
	.localentry func, .-func

To remove this assumption, GCC will now generate instead this global
entry point prolog sequence when using -mcmodel=large:

	.quad .TOC.-func
func:
	.reloc ., R_PPC64_ENTRY
	ld    r2, -8(r12)
	add   r2, r2, r12
	.localentry func, .-func

The new .reloc triggers an optimization in the linker that will
replace this new prolog with the original code (see above) if the
linker determines that the distance between .TOC. and func is in
range after all.

Since this new relocation is now present in module object files,
the kernel module loader is required to handle them too.  This
patch adds support for the new relocation and implements the
same optimization done by the GNU linker.

Cc: stable@vger.kernel.org
Signed-off-by: NUlrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

It has come to my attention that kprobe event stack tracing does not
work on powerpc. You can see with the following:

  # cd /sys/kernel/debug/tracing
  # echo stacktrace > trace_options
  # echo 'p kfree' > kprobe_events
  # echo 1 > events/kprobes/enable

Will print the following warning:
  save_stack_trace_regs() not implemented yet.

Although save_stack_trace() (which normal event stack traces use) is
implemented, save_stack_trace_regs() which kprobe events use is not.
This is a cheap attempt to implement that function.

Note, This may have issues if a task tries to get a stack trace from
another task with its regs, because it just passes in "current" to
save_context_stack(). But this does solve the issue with stack tracing
kprobe events.
Reported-by: NChunyu Hu <chuhu@redhat.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently we copy the whole mm_context_t to the paca but only access a
few bits of it.  This is wasteful of space paca and also takes quite
some time in the hot path of context switching.

This patch pulls in only the required bits from the mm_context_t to
the paca and on context switch, copies only those.

Benchmarking this (On top of Anton's recent MSR context switching
changes [1]) using processes and yield shows an improvement of almost
3% on POWER8:

  http://ozlabs.org/~anton/junkcode/context_switch2.c
  ./context_switch2 --test=yield --process 0 0

1. https://lists.ozlabs.org/pipermail/linuxppc-dev/2015-October/135700.htmlSigned-off-by: NMichael Neuling <mikey@neuling.org>
[mpe: Rename paca fields to be mm_ctx_foo rather than context_foo]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds a function to copy the mm->context to the paca.  This is
only a basic conversion for now but will be used more extensively in
the next patch.

This also adds #ifdef CONFIG_PPC_BOOK3S around this code since it's
not used elsewhere.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

cppcheck picked up that there were a couple of missing va_end()
calls in functions using va_start().
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Reviewed-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

PPC476FPE has a different PVR from previous PPC476 processors. The
kexec code checks the PVR in order to correctly setup the MMU. When
the initial support for 476FPE processors was added the corresponding
change in the kexec code was missed. This patch simply adds the check
and solves the following bug on kexec:

kexec: Starting new kernel
Bye!
Unable to handle kernel paging request for instruction fetch
Faulting instruction address: 0xee9a50f8
cpu 0x0: Vector: 400 (Instruction Access) at [ee9d7d20]
    pc: ee9a50f8
    lr: ee9a50e4
    sp: ee9d7dd0
    msr: 21020
    current = 0xee40f000
    pid   = 960, comm = kexec
enter ? for help
[link register   ] ee9a50e4
[ee9d7dd0] c0013748 default_machine_kexec+0x58/0x70 (unreliable)
[ee9d7df0] c0012f04 machine_kexec+0x34/0x40
[ee9d7e00] c00aa1ec kernel_kexec+0x9c/0xb0
[ee9d7e20] c005d704 SyS_reboot+0x1f4/0x220
[ee9d7f40] c000db68 ret_from_syscall+0x0/0x3c
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The STD_EXCEPTION_PSERIES macro takes both a vector number, and a
location (memory address). However both are always identical, so combine
them to save repeating ourselves.

This does mean an exception handler must always exist at the location in
memory that matches its vector number. But that's OK because this is the
"STD" macro (standard), which does exactly that. We have other macros
for the other cases, eg. STD_EXCEPTION_PSERIES_OOL (out of line).
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This is only used in one location, open code it.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

HMT_MEDIUM_LOW_HAS_PPR is only used in once place, open code it.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

HMT_MEDIUM_PPR_DISCARD is a macro which is present at the start of most
of our first level exception handlers. It conditionally executes a
HMT_MEDIUM instruction, which sets the processor priority to medium.

On on modern systems, ie. Power7 and later, it is nop'ed out at boot.
All it does is make the exception vectors more cramped, and consume 4
bytes of icache.

On old systems it has the effect of boosting the processor priority at
the start of exception processing. If we were previously in the idle
loop for example, we may be at low or very low priority. This is
desirable as we want to process the exception as fast as possible.

However looking closely at the generated code, we see that in all cases
we execute another HMT_MEDIUM just four instructions later. With code
patching applied, the final code on an old (Power6) system will look
like, eg:

  c000000000000300 <data_access_pSeries>:
  c000000000000300:	7c 42 13 78	mr	r2,r2		<-
  c000000000000304:	7d b2 43 a6	mtsprg	2,r13
  c000000000000308:	7d b1 42 a6	mfsprg	r13,1
  c00000000000030c:	f9 2d 00 80	std	r9,128(r13)
  c000000000000310:	60 00 00 00	nop
  c000000000000314:	7c 42 13 78	mr	r2,r2		<-

So I suggest that the added code complexity of HMT_MEDIUM_PPR_DISCARD is
not justified by the benefit of boosting the processor priority for the
duration of four instructions, and therefore we drop it.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

There are no longer any users of enter_rtas() outside of rtas.c, so make
it "private", by moving the declaration inside rtas.c. Hopefully this
will encourage people to use one of the wrappers which takes the sharp
edges off the RTAS calling sequence.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Although call_rtas_display_status() does actually want to use the
regular RTAS locking, it doesn't want the extra logic that is in
rtas_call(), so currently it open codes the logic.

Instead we can use rtas_call_unlocked(), after taking the RTAS lock.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Most users of RTAS (Run-Time Abstraction Services) use rtas_call(),
which deals with locking as well as endian handling.

However we have two users outside of rtas.c that can't use rtas_call()
because they have different locking requirements.

The hotplug CPU code can't take the RTAS lock because the CPU would go
offline with the lock held and no other CPUs would be able to call RTAS
until the CPU came back online.

The xmon code doesn't want to take the lock because it would risk dead
locking when we are trying to recover from a crash.

Both sites required multiple patches when we added little endian
support, proving that programmers can't do endian right.

Although that ship has sailed, we can still clean the code up by
providing an unlocked version of rtas_call() which avoids the need to
open code the logic elsewhere.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

GregorianDay() is supposed to calculate the day of the week
(tm->tm_wday) for a given day/month/year. In that calcuation it
indexed into an array called MonthOffset using tm->tm_mon-1. However
tm_mon is zero-based, not one-based, so this is off-by-one. It also
means that every January, GregoiranDay() will access element -1 of
the MonthOffset array.

It also doesn't appear to be a correct algorithm either: see in
contrast kernel/time/timeconv.c's time_to_tm function.

It's been broken forever, which suggests no-one in userland uses
this. It looks like no-one in the kernel uses tm->tm_wday either
(see e.g. drivers/rtc/rtc-ds1305.c:319).

tm->tm_wday is conventionally set to -1 when not available in
hardware so we can simply set it to -1 and drop the function.
(There are over a dozen other drivers in drivers/rtc that do
this.)

Found using UBSAN.

Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrew Morton <akpm@linux-foundation.org> # as an example of what UBSan finds.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Print MSR TM bits in oops messages.  This appends them to the end
like this:

    MSR: 8000000502823031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[TE]>

You get the TM[] only if at least one TM MSR bit is set.  Inside the
TM[], E means Enabled (bit 32), S means Suspended (bit 33), and T
means Transactional (bit 34)

If no bits are set, you get no TM[] output.

Include rework of printbits() to handle this case.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We should not expect pte bit position in asm code. Simply
by moving part of that to C
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Bit 7 of the "Header Type" register indicates a multi-function device when
set.  Bits 0-6 contain encoded values, where 0x1 indicates a PCI-PCI
bridge.  It is incorrect to test this as though it were a mask.

For example, while the PCI 3.0 spec only defines values 0x0, 0x1, and 0x2,
it's conceivable that a future spec could define 0x3 to mean something
else; then tests for "(hdr_type & 0x7f) & PCI_HEADER_TYPE_BRIDGE" would
incorrectly succeed for this new 0x3 header type.

Test bits 0-6 of the Header Type for equality with PCI_HEADER_TYPE_BRIDGE.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Two DSCR tests have a hack in them:

	/*
	 * XXX: Force a context switch out so that DSCR
	 * current value is copied into the thread struct
	 * which is required for the child to inherit the
	 * changed value.
	 */
	sleep(1);

We should not be working around this in the testcase, it is a kernel bug.
Fix it by copying the current DSCR to the child, instead of what we
had in the thread struct at last context switch.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

commit 152d523e ("powerpc: Create context switch helpers save_sprs()
and restore_sprs()") moved the restore of SPRs after the call to _switch().

There is an issue with this approach - new tasks do not return through
_switch(), they are set up by copy_thread() to directly return through
ret_from_fork() or ret_from_kernel_thread(). This means restore_sprs() is
not getting called for new tasks.

Fix this by moving restore_sprs() before _switch().

Fixes: 152d523e ("powerpc: Create context switch helpers save_sprs() and restore_sprs()")
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit a0e72cf1 ("powerpc: Create msr_check_and_{set,clear}()")
removed a call to check_if_tm_restore_required() in the
enable_kernel_*() functions. Add them back in.

Fixes: a0e72cf1 ("powerpc: Create msr_check_and_{set,clear}()")
Reported-by: NRashmica Gupta <rashmicy@gmail.com>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This reverts commit 527d10ef.

The reverted commit breaks cxlflash devices following an EEH reset (and
possibly other cxl devices, however this has not been tested).

The reverted commit changed the behaviour of eeh_reset_device() so that PHB
PEs are not unfrozen following the completion of the reset. This should not
be problematic, as no device resources should have been associated with the
PHB PE.

However, when attempting to load the cxlflash driver after a reset, the
driver attempts to read Vital Product Data through a call to
pci_read_vpd() (which is called on the physical cxl device, not on the
virtual AFU device). pci_read_vpd() in turn attempts to read from the cxl
device's config space. This fails, as the PE it's trying to read from is
still frozen. In turn, the driver gets an -ENODEV and fails to initialise.

It appears this issue only affects some parts of the VPD area, as "lspci
-vvv", which only reads a subset of the VPD bytes, is not broken by the
original patch.

At this stage, we don't fully understand why we're trying to read a frozen
PE, and we don't know how this affects other cxl devices. It is possible
that there is an underlying bug in the cxl driver or the powerpc CAPI
support code, or alternatively a bug in the PCI resource allocation/mapping
code that is incorrectly mapping resources to PE#0.

As such, this fix is incomplete, however it is necessary to prevent a
serious regression in CAPI support.

In the meantime, revert the commit, especially as it was intended to be a
non-functional change.

Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Ian Munsie <imunsie@au1.ibm.com>
Cc: Daniel Axtens <dja@axtens.net>
Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Makes it easier to handle init vs core cleanly, though the change is
fairly invasive across random architectures.

It simplifies the rbtree code immediately, however, while keeping the
core data together in the same cachline (now iff the rbtree code is
enabled).
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Reviewed-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Remove a bunch of unnecessary fallback functions and group
things in a more logical way.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Most of __switch_to() is housekeeping, TLB batching, timekeeping etc.
Move these away from the more complex and critical context switching
code.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Create a single function that flushes everything (FP, VMX, VSX, SPE).
Doing this all at once means we only do one MSR write.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Create a single function that gives everything up (FP, VMX, VSX, SPE).
Doing this all at once means we only do one MSR write.

A context switch microbenchmark using yield():

http://ozlabs.org/~anton/junkcode/context_switch2.c

./context_switch2 --test=yield --fp --altivec --vector 0 0

shows an improvement of 3% on POWER8.
Signed-off-by: NAnton Blanchard <anton@samba.org>
[mpe: giveup_all() needs to be EXPORT_SYMBOL'ed]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>