32-bit and 64-bit ARM use very different infrastructure to register a PCI
host bridge.  The Tegra PCIe host controller driver currently only supports
the 32-bit ARM infrastructure, so prevent it from being built on 64-bit ARM
where it will break.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

skb->truesize is not meant to be tracking amount of used bytes
in an skb, but amount of reserved/consumed bytes in memory.

For instance, if we use a single byte in last page fragment,
we have to account the full size of the fragment.

skb->truesize can be very different from skb->len, that has
a very specific safety purpose.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b4d2394d ("dsa: Replace mii_bus with a generic host device")
replaces mii_bus with a generic host_dev, and introduces
dsa_host_dev_to_mii_bus() to support conversion from host_dev to mii_bus.
However, in some cases it uses to_mii_bus to perform that conversion.
Since host_dev is not the phy bus device but typically a platform device,
this fails and results in a crash with the affected drivers.

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff81781d35>] __mutex_lock_slowpath+0x75/0x100
PGD 406783067 PUD 406784067 PMD 0
Oops: 0002 [#1] SMP
...
Call Trace:
[<ffffffff810a538b>] ? pick_next_task_fair+0x61b/0x880
[<ffffffff81781de3>] mutex_lock+0x23/0x37
[<ffffffff81533244>] mdiobus_read+0x34/0x60
[<ffffffff8153b95a>] __mv88e6xxx_reg_read+0x8a/0xa0
[<ffffffff8153b9bc>] mv88e6xxx_reg_read+0x4c/0xa0

Fixes: b4d2394d ("dsa: Replace mii_bus with a generic host device")
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't ring the doorbell, and don't do PIO.  This will also prevent
 TX Push, because there will be more than one buffer waiting when
 the doorbell is rung.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove calling cancel_delayed_work_sync() for runtime suspend,
because it would cause dead lock. Instead, return -EBUSY to
avoid the device enters suspending if the net is running and
the delayed work is pending or running. The delayed work would
try to wake up the device later, so the suspending is not
necessary.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case that the IP header has optional field at the end, this patch will
get the port numbers after that field, and compute the hash. The general
parser skb_flow_dissect() is used here.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pskb_may_pull maybe change skb->data and make eth pointer oboslete,
so eth needs to reload

Fixes: 91269e39 ("vxlan: using pskb_may_pull as early as possible")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This simplifies the lanai.c driver by using
the module_pci_driver() macro, at the expense
of losing only debugging messages.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the Haswell platform, a split BAR option to allow creation of 2
32bit BARs (4 and 5) from the 64bit BAR 4. Adding support for this
new option.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Instead of using a module parameter, we should detect the errata via
PCI DID and then set an appropriate flag. This will be used for additional
errata later on.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

To simplify some of the platform detection code. Move the platform detection
to a function to be called earlier.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Move the platform detection function to separate functions to allow
easier maintenence.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Create a debugfs entry for the NTB device to log the basic device info,
as well as display the error count on a number of registers.
Signed-off-by: NJon Mason <jon.mason@intel.com>

Add Thrustmaster as Xbox 360 controller vendor. This is required for
example to make the GP XID (044f:b326) gamepad work.
Signed-off-by: NTommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add the USB ID for the Xbox 360 Thrustmaster Ferrari 458 Racing Wheel.
Signed-off-by: NTommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The check to see whether the device is already disabled in
max77693_haptic_disable() was inversed, this change corrects it.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

xenkbd_disconnect_backend doesn't free grant table entry.  This bug affects
live migration.

xenkbd_disconnect_backend uses gnttab_end_foreign_access_ref to handle
grant table entry which doesn't really free an entry.

Thus every time we do xenkbd_resume, grant table entry increses by one. As
an grant table entry occupies 8 bytes, an grant table page has at most 512
entries. Every 512 times we do xenkdb_resume, grant table pages increses by
one.

After around 3500 times of live migration, grant table pages will increase
by 7, causing too many pages to populate and hitting max_pages limit when
assigning pages.Thus assign_pages will fail, so will live migration.
Signed-off-by: NChang Huaixin <huaixin.chx@alibaba-inc.com>
Acked-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The check for vfinfo is not sufficient because it does not protect
against specifying vf that is outside of sriov_num_vfs range.
All of the ndo functions have a check for it except for
ixgbevf_ndo_set_spoofcheck().

The following patch is all we need to protect against this panic:

ip link set p96p1 vf 0 spoofchk off
BUG: unable to handle kernel NULL pointer dereference at 0000000000000052
IP: [<ffffffffa044a1c1>]
ixgbe_ndo_set_vf_spoofchk+0x51/0x150 [ixgbe]
Reported-by: NThierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NThierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Compiling with CONFIG_FM10K=y and VXLAN=m resulting in linking error:

   drivers/built-in.o: In function `fm10k_open':
   (.text+0x1f9d7a): undefined reference to `vxlan_get_rx_port'
   make: *** [vmlinux] Error 1

The fix follows the same strategy as I40E.
Signed-off-by: NAndy Zhou <azhou@nicira.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After grabbing the mailbox lock and detecting an error, the lock must be
released before the error code can be returned.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The atmel serial driver uses dmaengine APIs but never included the dmaengine
header as it was getting inculded thru one of driver headers.

commit 3d588f83 - "dmaengine: dw: split
dma-dw.h to platform and private parts" broke this as it moved headers
around.  Fix this by doing the right thing to include the dmaengine header
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Fixes: 08f738be (serial: at91: add tx dma support)
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Set the flag to fetch the host state before kicking off the service task
that reads the host state when bringing the interface back up.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: NWei Yan <sledge.yanwei@huawei.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

pskb_may_pull should be used to check if skb->data has enough space,
skb->len can not ensure that.

Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when netif_rx() is done, the netif_rx handled skb maybe be freed,
and should not be used.
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For each Rx frame the eTSEC writes its FCS (Frame Check Sequence)
to the Rx buffer.

The eTSEC h/w manual states in the "Receive Buffer Descriptor Field
Descriptions" table:
"Data length is the number of octets written by the eTSEC into this BD's
data buffer if L is cleared (the value is equal to MRBLR), or, if L is
set, the length of the frame including *CRC*, FCB (if RCTRL[PRSDEP > 00),
preamble (if MACCFG2[PreAmRxEn]=1), time stamp (if RCTRL[TS] = 1) and
any padding (RCTRL[PAL])."

Though the FCS bytes are removed by the driver before passing the skb
to the net stack, the Rx buffer size computation does not currently
take into account the FCS bytes (4 bytes).
Because the Rx buffer size is multiple of 512 bytes, leaving out the
FCS is not a problem for the default MTU of 1500, as the Rx buffer size
is 1536 in this case.  However, for custom MTUs, where the difference
between the MTU size and the Rx buffer size is less, this can be a
problem as the computed Rx buffer size won't be enough to accomodate
the FCS for a received frame that is big enough (close to MTU size).
In such case the received frame is considered to be incomplete (L flag
not set in the RxBD status) and silently dropped.

Note that the driver does not currently support S/G on Rx, so it has to
compute its Rx buffer size based on the MTU of the device.
Reported-by: NKristian Otnes <kotnes@cisco.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 0b725a2c
    net: Remove ndo_xmit_flush netdev operation, use signalling instead.

added code that looks at skb->xmit_more after the skb has
been put in TX VQ. Since some paths process the ring and free the skb
immediately, this can cause use after free.

Fix by storing xmit_more in a local variable.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register.
The current SW flow is:
		ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
		ts_counter_ns = ENET0->ATVR;
The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent.

ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue:
After set ENET_ATCR[Capture], there need some time cycles before the counter
value is capture in the register clock domain. The wait-time-cycles is at least
6 clock cycles of the slower clock between the register clock and the 1588 clock.
So need something like:
		ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
		wait();
		ts_counter_ns = ENET0->ATVR;

For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the
wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay
before cpu read ATVR register.

Changes V2:
Modify the commit/comments log to describe the issue clearly.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
atiixp_ide_timing.

The following Coccinelle semantic patch detects the case:

@tn1@
type td;
@@

typedef struct { ... } td;

@script:python tf@
td << tn1.td;
tdres;
@@

coccinelle.tdres = td;

@@
type tn1.td;
identifier tf.tdres;
@@

-typedef
 struct
+  tdres
   { ... }
-td
 ;

@@
type tn1.td;
identifier tf.tdres;
@@

-td
+ struct tdres
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the change to struct input_mt_pos some variables are now bitfields
instead of integers. Automatic conversion from integer to bitfield entry
destroys information, therefore enforce boolean interpretation instead.

Link: https://bugzilla.redhat.com/show_bug.cgi?id=1114768
Fixes: 02d04254 ("Input: alps - use struct input_mt_pos to track coordinates")
Signed-off-by: NAndreas Bosch <linux@progandy.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Identified by kbuild test robot. csk family is always set to be AF_INET or
AF_INET6, so skb will always be initialized to some value but there is no harm
in silencing the warning anyways.
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Fixes : f42bb57c ('cxgb4i : Fix -Wunused-function warning')
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

since users have been move to fsl_dma_external_start() API, so remove this
now
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

carma-fpga driver uses device control with custom FSLDMA_EXTERNAL_START
command. Since we wnat to deprecate the device control, move this driver to
use new fsl_dma_external_start() API
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The drivers should use dmaengine_slave_config() and dmaengine_prep_dma_sg()
API instead of accessing the device_control which will be deprecated soon
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The freescale driver uses custom device control FSLDMA_EXTERNAL_START to
put the controller in external start mode.
Since we are planning to deprecate the device control, move this to exported
API. Subsequent patches will remove the FSLDMA_EXTERNAL_START
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: NVinod Koul <vinod.koul@intel.com>