The error messages for the failure of dmaengine_prep_slave_sg are
not necessary, this patch removes all these pr_err, and returns with
the proper error code -EINVAL, not -1.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This patch adds request_mem_region() prior ioremap() for diskonchip
driver. This will allow to check if memory region is occupied by any
other device, for example in case if we have memory region for several
optional devices and only one device can be used at once.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Use devm_request_irq to simplify the code.
Also remove the unused fields of structure resources{}.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Use the devm_ioremap_resource to simplify the code.

[Note: as a side effect, this adds a missing call to request_memory().]
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The gpmi_nfc_* is the legacy name. In order to avoid the confusion,
The patch renames the gpmi_nfc_* functions to gpmi_nand_*.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We do not use the chip->oob_poi in the mx23_write_transcription_stamp.
So remove the unused line.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We do not scan the BBT after we call the gpmi_pre_bbt_scan,
so it has lost the meaning of existence.

This patch merges this function into gpmi_init_last, and delete it.
This patch does not change any logic.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The local array feature[] is in the stack. We can see the warning
when we enable the CONFIG_DMA_API_DEBUG:
----------------------------------------------------------
WARNING: at lib/dma-debug.c:950 check_for_stack+0xac/0xf8()
gpmi-nand 112000.gpmi-nand: DMA-API: device driver maps memory fromstack [addr=dc05be34]
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.17-16851-g2414a73 #1324
[<80014cbc>] (unwind_backtrace+0x0/0x138) from [<8001251c>] (show_stack+0x10/0x14)
[<8001251c>] (show_stack+0x10/0x14) from [<8002699c>] (warn_slowpath_common+0x4c/0x68)
[<8002699c>] (warn_slowpath_common+0x4c/0x68) from [<80026a4c>] (warn_slowpath_fmt+0x30/0x40)
[<80026a4c>] (warn_slowpath_fmt+0x30/0x40) from [<8028e2f8>] (check_for_stack+0xac/0xf8)
[<8028e2f8>] (check_for_stack+0xac/0xf8) from [<8028e438>] (debug_dma_map_sg+0xf4/0x188)
[<8028e438>] (debug_dma_map_sg+0xf4/0x188) from [<803968d0>] (prepare_data_dma+0xb8/0x1a8)
[<803968d0>] (prepare_data_dma+0xb8/0x1a8) from [<80397b20>] (gpmi_send_data+0x84/0xfc)
[<80397b20>] (gpmi_send_data+0x84/0xfc) from [<8038c2b4>] (nand_onfi_set_features+0x50/0x74)
[<8038c2b4>] (nand_onfi_set_features+0x50/0x74) from [<80397198>] (gpmi_extra_init+0x90/0x170)
[<80397198>] (gpmi_extra_init+0x90/0x170) from [<8039520c>] (gpmi_nand_probe+0x2f8/0xb3c)
[<8039520c>] (gpmi_nand_probe+0x2f8/0xb3c) from [<8031b974>] (platform_drv_probe+0x18/0x1c)
----------------------------------------------------------

The patch uses the kzalloc to allocate the buffer, and free it when
we do not use it anymore.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The Armada BCH configuration in this driver uses one of the two
following ECC schemes:

 16-bit correction per 2048 bytes
 16-bit correction per 1024 bytes

These are sufficient for mapping to the 4-bit per 512-bytes and 8-bit
per 512-bytes (respectively) minimum correctability requirements of many
common NAND.

The current code only checks for the required strength (4-bit or 8-bit)
without checking the ECC step size that is associated with that strength
(and simply assumes it is 512). While that is often a safe assumption to
make, let's make it explicit, since we have that information.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>

This commit extends the ECC correctable error detection to include
ECC BCH errors. The number of BCH correctable errors can be any up to 16,
and the actual value is exposed in the NDSR register.

Therefore, we change some symbol names to refer to correctable or
uncorrectable (instead of single-bit or double-bit as it was in the
Hamming case) and while at it, cleanup the detection code slightly.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This commit adds write support for large pages (4 KiB, 8 KiB).
Such support is implemented by issuing a multiple command sequence,
transfering a set of 2 KiB chunks per transaction.

The splitted command sequence requires to send the SEQIN command
independently of the PAGEPROG command and therefore it's set as
an execution command.

Since PAGEPROG enables ECC, each 2 KiB chunk of data is written
together with ECC code at a controller-fixed location within
the flash page.

Currently, only devices with a 4 KiB page size has been tested.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

As preparation work to fully support large pages, this commit adds
the initial infrastructure to support splitted (aka chunked) I/O
operation. This commit adds support for read, and follow-up patches
will add write support.

When a read (aka READ0) command is issued, the driver loops issuing
the same command until all the requested data is transfered, changing
the 'extended' command field as needed.

For instance, if the driver is required to read a 4 KiB page, using a
chunk size of 2 KiB, the transaction is splitted in:
1. Monolithic read, first 2 KiB page chunk is read
2. Last naked read, second and last 2KiB page chunk is read

If ECC is enabled it is calculated on each chunk transfered and added
at a controller-fixed location after the data chunk that must be
spare area.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In preparation to support multiple (aka chunked, aka splitted)
page I/O, this commit adds 'data_buff_pos' and 'oob_buff_pos' fields
to keep track of where the next read (or write) should be done.

This will allow multiple calls to handle_data_pio() to continue
the read (or write) operation.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This commit adds support page programming with a non-zero "column"
address setting. This is important to support OOB writing, through
command sequences such as:

  cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, ofs);
  write_buf(mtd, oob_buf, 6);
  cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

To allow future support of multiple page reading/writing, move the data
buffer clean out of prepare_set_command().

This is done to prevent the data buffer from being cleaned on every command
preparation, when a multiple command sequence is implemented to read/write
pages larger than the FIFO size (2 KiB).
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This commit splits the prepare_command_pool() function into two
stages: prepare_start_command() / prepare_set_command().

This is a preparation patch without any functionality changes,
and is meant to allow support for multiple page reading/writing
operations.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

READ0 and READOOB command preparation has a falltrough to SEQIN
case, where the command address is specified.
This is certainly confusing and makes the code less readable with
no added value. Let's remove it.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Let's simplify the code by first introducing a helper function
to set the page address, as done by the READ0, READOOB and SEQIN
commands.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Command buffer #3 is not properly cleared and it keeps the last
set value. Fix this by clearing when a command is setup.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This commit adds the BCH ECC support available in NFCv2 controller.
Depending on the detected required strength the respective ECC layout
is selected.

This commit adds an empty ECC layout, since support to access large
pages is first required. Once that support is added, a proper ECC
layout will be added as well.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In pxa3xx_nand_sensing() instead of simply using info->is_ready
after issuing a command, the correct way of checking is to wait
for the device to be ready through the chip's waitfunc().
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The expected behavior of the waitfunc() NAND chip call is to wait
for the device to be READY (this is a standard chip line).
However, the current implementation does almost nothing, which opens
the possibility of issuing a command to a non-ready device.

Fix this by adding a new completion to wait for the ready event to arrive.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add a comment clarifying the use of pxa3xx_set_datasize() which is only
applicable on data read/write commands (i.e. commands with a data cycle,
such as READID, READ0, STATUS, etc.)
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

There's no need to privately store the device page size as it's
available in mtd structure field mtd->writesize.
Also, this removes the hardcoded page size value, leaving the
auto-detected value only.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Introduce a fifo_size field to represent the size of the controller's
FIFO buffer, and use it to distinguish that size from the amount
of data bytes to be read from the FIFO.

This is important to support devices with pages larger than the
controller's internal FIFO, that need to read the pages in FIFO-sized
chunks.

In particular, the current code is at least confusing, for it mixes
all the different sizes involved: FIFO size, page size and data size.

This commit starts the cleaning by removing the info->page_size field
that is not currently used. The host->page_size field should also
be removed and use always mtd->writesize instead. Follow up commits
will clean this up.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Whenever possible, it's always better to use the generic chip->cmdfunc
instead of the internal pxa3xx_nand_cmdfunc().
In this particular case, this will allow to have multiple cmdfunc()
implementations for different SoC variants.
Reviewed-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In order to customize early settings depending on the detected SoC variant,
move the detection to be before the nand_chip struct filling.

In a follow-up patch, this change is needed to detect the variant *before*
the call to alloc_nand_resource(), which allows to set a different cmdfunc()
for each variant.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

As per the ecc.read_page() prototype, we must return the maximum number
of bitflips that were corrected on any one region covering an ecc step.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The current driver doesn't support sub-page writing, so report
that to the NAND core.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Since we have now support for the NFCv2 controller found on
Armada 370/XP platforms.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Given there's no public specification to this date, and in order
to capture some important details and singularities about the
controller let's document them once and for good.

Cc: linux-doc@vger.kernel.org
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Since the driver supports the new compatible string, the binding
documentation must be updated to reflect it.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This allows to drop a few casts.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

mtd_info.name is "const char *"
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

device_driver.name is "const char *"
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

map_info.name is "const char *"
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Fix the following checkpatch warnings:

WARNING: line over 80 characters
#268: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:268:
+	* consecutive reboots. The latter case has not been seen on the MX23 yet,

WARNING: space prohibited before semicolon
#356: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:356:
+		(target.tRHOH_in_ns >= 0) ;

WARNING: space prohibited before semicolon
#1006: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:1006:
+		BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles)       ;
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Using devm_clk_get() can make the code smaller and cleaner.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In default way, we use the ecc_strength/ecc_step size calculated by ourselves
and use all the OOB area.

This patch adds a new property : "fsl,use-minimum-ecc"

If we enable it, we will firstly try to use the datasheet's minimum required
ECC provided by the MTD layer (the ecc_strength_ds/ecc_step_ds fields
in the nand_chip{}). So we may have free space in the OOB area by using the
minimum ECC, and we may support JFFS2 with some SLC NANDs, such as Micron's
SLC NAND.

If we fail to use the minimum ECC, we will use the legacy method to calculate
the ecc_strength and ecc_step size.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>