This is a companion to i915_gem_obj_prepare_shmem_read() that prepares
the backing storage for direct writes. It first serialises with the GPU,
pins the backing storage and then indicates what clfushes are required in
order for the writes to be coherent.

Whilst here, fix support for ancient CPUs without clflush for which we
cannot do the GTT+clflush tricks.

v2: Add i915_gem_obj_finish_shmem_access() for symmetry
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160818161718.27187-8-chris@chris-wilson.co.uk

Since vfree() now likes to WARN when passed a non-page-aligned pointer,
we need to discard the low bits to comply with it.

Fixes: d31d7cb1 ("drm/i915: Support for creating write combined type vmaps")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160818161718.27187-3-chris@chris-wilson.co.uk

If userspace is asynchronously streaming into the batch or other
execobjects, we may not flush those writes along with a change in cache
domain (as there is no change). Therefore those writes may end up in
internal chipset buffers and not visible to the GPU upon execution. We
must issue a flush command or otherwise we encounter incoherency in the
batchbuffers and the GPU executing invalid commands (i.e. hanging) quite
regularly.

v2: Throw a paranoid wmb() into the general flush so that we remain
consistent with before.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90841
Fixes: 1816f923 ("drm/i915: Support creation of unbound wc user...")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Tested-by: NMatti Hämäläinen <ccr@tnsp.org>
Cc: stable@vger.kernel.org
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160818161718.27187-1-chris@chris-wilson.co.uk

Just another useful register to inspect following a GPU hang.

v2: Remove partial decoding of RING_MODE to userspace, be consistent and
use GEN > 2 guards around RING_MODE everywhere.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-32-git-send-email-chris@chris-wilson.co.uk

It is useful when looking at captured error states to check the recorded
BBADDR register (the address of the last batchbuffer instruction loaded)
against the expected offset of the batch buffer, and so do a quick check
that (a) the capture is true or (b) HEAD hasn't wandered off into the
badlands.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-30-git-send-email-chris@chris-wilson.co.uk

Since contexts are not currently shared between userspace processes, we
have an exact correspondence between context creator and guilty batch
submitter. Therefore we can save some per-batch work by inspecting the
context->pid upon error instead. Note that we take the context's
creator's pid rather than the file's pid in order to better track fd
passed over sockets.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-29-git-send-email-chris@chris-wilson.co.uk

This little helper only exists to safely discard the upper unused 32bits
of the general 64-bit VMA address - as we know that all Global GTT
currently are less than 4GiB in size and so that the upper bits must be
zero. In many places, we use a u32 for the global GTT offset and we want
to document where we are discarding the full VMA offset.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-28-git-send-email-chris@chris-wilson.co.uk

Treat the VMA as the primary struct responsible for tracking bindings
into the GPU's VM. That is we want to treat the VMA returned after we
pin an object into the VM as the cookie we hold and eventually release
when unpinning. Doing so eliminates the ambiguity in pinning the object
and then searching for the relevant pin later.

v2: Joonas' stylistic nitpicks, a fun rebase.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-27-git-send-email-chris@chris-wilson.co.uk

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-23-git-send-email-chris@chris-wilson.co.uk

When working with contexts, we most frequently want the GGTT VMA for the
context state, first and foremost. Since the object is available via the
VMA, we need only then store the VMA.

v2: Formatting tweaks to debugfs output, restored some comments removed
in the next patch
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-15-git-send-email-chris@chris-wilson.co.uk

The VMA are unreferenced, they belong to the object and live until they
are closed. However, if we want to use the VMA as a cookie and use it to
keep the object alive, we want to hold onto a reference to the object
for the lifetime of the VMA cookie. To facilitate this, add a couple of
simple wrappers for managing the reference count on the object owning the
VMA.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-11-git-send-email-chris@chris-wilson.co.uk

A simple little macro to clear a pointer and return the old value. This
is useful for writing

	value = *ptr;
	if (!value)
		return;

	*ptr = 0;
	...
	free(value);

in a slightly more concise form:

	value = fetch_and_zero(ptr);
	if (!value)
		return;

	...
	free(value);

with the idea that this establishes a pattern that may be extended for
atomic use (using xchg or cmpxchg) i.e. atomic_fetch_and_zero() and
similar to llist.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-10-git-send-email-chris@chris-wilson.co.uk

No longer is knowing how much of the GTT (both mappable aperture and
beyond) relevant, and the output clutters the real information - that is
how many objects are allocated and bound (and by who) so that we can
quickly grasp if there is a leak.

v2: Relent, and rename pinned to indicate display only. Since the
display objects are semi-static and are of variable size, they are the
interesting objects to watch over time for aperture leaking. The other
pins are either static (such as the scratch page) or very short lived
(such as execbuf) and not part of the precious GGTT.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-6-git-send-email-chris@chris-wilson.co.uk

When capturing the error state, we do not need to know about every
address space - just those that are related to the error. We know which
context is active at the time, therefore we know which VM are implicated
in the error. We can then restrict the VM which we report to the
relevant subset.

v2: s/i/count_active/ (and similar)
    Rewrite label generation for "Buffers"
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-2-git-send-email-chris@chris-wilson.co.uk

Not only does it make for good documentation and debugging aide, but it is
also vital for when we want to unwind requests - such as when throwing away
an incomplete request.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1470414607-32453-2-git-send-email-arun.siluvery@linux.intel.comReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-1-git-send-email-chris@chris-wilson.co.uk

This patch provides the infrastructure for performing a 16-byte aligned
read from WC memory using non-temporal instructions introduced with sse4.1.
Using movntdqa we can bypass the CPU caches and read directly from memory
and ignoring the page attributes set on the CPU PTE i.e. negating the
impact of an otherwise UC access. Copying using movntdqa from WC is almost
as fast as reading from WB memory, modulo the possibility of both hitting
the CPU cache or leaving the data in the CPU cache for the next consumer.
(The CPU cache itself my be flushed for the region of the movntdqa and on
later access the movntdqa reads from a separate internal buffer for the
cacheline.) The write back to the memory is however cached.

This will be used in later patches to accelerate accessing WC memory.

v2: Report whether the accelerated copy is successful/possible.
v3: Function alignment override was only necessary when using the
function target("sse4.1") - which is not necessary for emitting movntdqa
from __asm__.
v4: Improve notes on CPU cache behaviour vs non-temporal stores.
v5: Fix byte offsets for unrolled moves.
v6: Find all remaining typos of "movntqda", use kernel_fpu_begin.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471001999-17787-2-git-send-email-chris@chris-wilson.co.uk

vmaps has a provision for controlling the page protection bits, with which
we can use to control the mapping type, e.g. WB, WC, UC or even WT.
To allow the caller to choose their mapping type, we add a parameter to
i915_gem_object_pin_map - but we still only allow one vmap to be cached
per object. If the object is currently not pinned, then we recreate the
previous vmap with the new access type, but if it was pinned we report an
error. This effectively limits the access via i915_gem_object_pin_map to a
single mapping type for the lifetime of the object. Not usually a problem,
but something to be aware of when setting up the object's vmap.

We will want to vary the access type to enable WC mappings of ringbuffer
and context objects on !llc platforms, as well as other objects where we
need coherent access to the GPU's pages without going through the GTT

v2: Remove the redundant braces around pin count check and fix the marker
     in documentation (Chris)

v3:
- Add a new enum for the vmalloc mapping type & pass that as an argument to
   i915_object_pin_map. (Tvrtko)
- Use PAGE_MASK to extract or filter the mapping type info and remove a
   superfluous BUG_ON.(Tvrtko)

v4:
- Rename the enums and clean up the pin_map function. (Chris)

v5: Drop the VM_NO_GUARD, minor cosmetics.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471001999-17787-1-git-send-email-chris@chris-wilson.co.uk

Until now code was calling hweight32 to figure out the
number from device_info->ring_mask at runtime. Instead
we can cache it at engine init time and use directly.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1470842530-35854-1-git-send-email-tvrtko.ursulin@linux.intel.com

In the preceding patches we made sure that:
- the LVDS encoder takes care of reiniting both the LVDS register
and its PPS
- the eDP encoder takes care of reiniting its PPS
- the PPS register unlocking workaround is applied explicitly whenever
the PPS context is lost

Based on the above we can safely remove the opaque LVDS and PPS save /
restore from generic code.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-6-git-send-email-imre.deak@intel.com

The PPS registers are pretty much the same everywhere, the differences
being:
- Register fields appearing, disappearing from one platform to the
  next: panel-reset-on-powerdown, backlight-on, panel-port,
  register-unlock
- Different register base addresses
- Different number of PPS instances: 2 on VLV/CHV/BXT, 1 everywhere
  else.

We can merge the separate set of PPS definitions by extending the PPS
instance argument to all platforms and using instance 0 on platforms
with a single instance. This means we'll need to calculate the register
addresses dynamically based on the given platform and PPS instance.

v2:
- Simplify if ladder in intel_pps_get_registers(). (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-1-git-send-email-imre.deak@intel.com

The bottom-half we use for processing the breadcrumb interrupt is a
task, which is an RCU protected struct. When accessing this struct, we
need to be holding the RCU read lock to prevent it disappearing beneath
us. We can use the RCU annotation to mark our irq_seqno_bh pointer as
being under RCU guard and then use the RCU accessors to both provide
correct ordering of access through the pointer.

Most notably, this fixes the access from hard irq context to use the RCU
read lock, which both Daniel and Tvrtko complained about.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470761272-1245-3-git-send-email-chris@chris-wilson.co.uk

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function would call drm_modeset_lock_all, while the suspend/resume
functions already have their own locking. Fix this by factoring out
__intel_display_resume, and calling the atomic helpers for duplicating
atomic state and disabling all crtc's during suspend.

Changes since v1:
- Deal with -EDEADLK right after lock_all and clean up calls
  to hw readout.
- Always take all modeset locks so updates during gpu reset are blocked.
Changes since v2:
- Fix deadlock in intel_update_primary_planes.
- Move WARN_ON(EDEADLK) to __intel_display_resume.
- pctx -> ctx
- only call __intel_display_resume on success in intel_display_resume.
Changes since v3:
- Rebase on top of dev_priv -> dev change.
- Use drm_modeset_lock_all_ctx instead of drm_modeset_lock_all.
Changes since v4 [by vsyrjala]:
- Deal with skip_intermediate_wm
- Update comment w.r.t. mode_config.mutex vs. ->detect()
- Rebase due to INTEL_GEN() etc.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: e2c8b870 ("drm/i915: Use atomic helpers for suspend, v2.")
Cc: stable@vger.kernel.org
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470428910-12125-2-git-send-email-ville.syrjala@linux.intel.com

In the previous commit, we moved the obj->tiling_mode out of a bitfield
and into its own integer so that we could safely use READ_ONCE(). Let us
now repair some of that damage by sharing the tiling_mode with its
companion, the fence stride.

v2: New magic
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-18-git-send-email-chris@chris-wilson.co.uk

Since we are not concerned with userspace racing itself with set-tiling
(the order is indeterminant even if we take a lock), then we can safely
read back the single obj->tiling_mode and do the static lookup of
swizzle mode without having to take a lock.

get-tiling is reasonably frequent due to the back-channel passing around
of tiling parameters in DRI2/DRI3.

v2: Make tiling_mode a full unsigned int so that we can trivially use it
with READ_ONCE(). Separating it out into manual control over the flags
field was too noisy for a simple patch. Note that we could use the lower
bits of obj->stride for the tiling mode.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-16-git-send-email-chris@chris-wilson.co.uk

After removing the user of this wart, we can remove the wart entirely.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-10-git-send-email-chris@chris-wilson.co.uk

The principal motivation for this was to try and eliminate the
struct_mutex from i915_gem_suspend - but we still need to hold the mutex
current for the i915_gem_context_lost(). (The issue there is that there
may be an indirect lockdep cycle between cpu_hotplug (i.e. suspend) and
struct_mutex via the stop_machine().) For the moment, enabling last
request tracking for the engine, allows us to do busyness checking and
waiting without requiring the struct_mutex - which is useful in its own
right.

As a side-effect of having a robust means for tracking engine busyness,
we can replace our other busyness heuristic, that of comparing against
the last submitted seqno. For paranoid reasons, we have a semi-ordered
check of that seqno inside the hangchecker, which we can now improve to
an ordered check of the engine's busyness (removing a locked xchg in the
process).

v2: Pass along "bool interruptible" as being unlocked we cannot rely on
i915->mm.interruptible being stable or even under our control.
v3: Replace check Ironlake i915_gpu_busy() with the common precalculated value
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-6-git-send-email-chris@chris-wilson.co.uk

Before suspending (or unloading), we would first wait upon all rendering
to be completed and then disable the rings. This later step is a remanent
from DRI1 days when we did not use request tracking for all operations
upon the ring. Now that we are sure we are waiting upon the very last
operation by the engine, we can forgo clobbering the ring registers,
though we do keep the assert that the engine is indeed idle before
sleeping.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-5-git-send-email-chris@chris-wilson.co.uk

We are motivated to avoid using a bitfield for obj->active for a couple
of reasons. Firstly, we wish to document our lockless read of obj->active
using READ_ONCE inside i915_gem_busy_ioctl() and that requires an
integral type (i.e. not a bitfield). Secondly, gcc produces abysmal code
when presented with a bitfield and that shows up high on the profiles of
request tracking (mainly due to excess memory traffic as it converts
the bitfield to a register and back and generates frequent AGI in the
process).

v2: BIT, break up a long line in compute the other engines, new paint
for i915_gem_object_is_active (now i915_gem_object_get_active).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-23-git-send-email-chris@chris-wilson.co.uk

The individual bits inside obj->frontbuffer_bits are protected by each
plane->mutex, but the whole bitfield may be accessed by multiple KMS
operations simultaneously and so the RMW need to be under atomics.
However, for updating the single field we do not need to mandate that it
be under the struct_mutex, one more step towards its removal as the de
facto BKL.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-21-git-send-email-chris@chris-wilson.co.uk

We only need a very lightweight mechanism here as the locking is only
used for co-ordinating a bitfield.

v2: Move the cheap unlikely tests into the caller
v3: Move the kerneldoc into the header (now separated out into
intel_fronbuffer.h for better kerneldoc and readability)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtien <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-20-git-send-email-chris@chris-wilson.co.uk

Since i915_gem_obj_ggtt_pin() is an idiom breaking curry function for
i915_gem_object_ggtt_pin(), spare us the confusion and remove it.
Removing it now simplifies later patches to change the i915_vma_pin()
(and friends) interface.

v2: Add a redundant GEM_BUG_ON(!view) to
i915_gem_obj_lookup_or_create_ggtt_vma()
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-18-git-send-email-chris@chris-wilson.co.uk

During execbuffer we look up the i915_vma in order to reserve them in
the VM. However, we then do a double lookup of the vma in order to then
pin them, all because we lack the necessary interfaces to operate on
i915_vma - so introduce i915_vma_pin()!

v2: Tidy parameter lists to remove one level of redirection in the hot
path.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-15-git-send-email-chris@chris-wilson.co.uk

For consistency, internal functions should take drm_i915_private rather
than drm_device. Now that we are subclassing drm_device, there are no
more size wins, but being consistent is its own blessing.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-12-git-send-email-chris@chris-wilson.co.uk

In order to be consistent with other address space functions, we want to
pass around 64-bit sizes, even though all known global GTT are limited
to 4GiB. Similarly, we are trying to be consistent in using the _ggtt_
nomenclature when referring to the special global GTT.

v2: Update docs to consistently state "global GTT".
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-11-git-send-email-chris@chris-wilson.co.uk

Our GPUs impose certain requirements upon buffers that depend upon how
exactly they are used. Typically this is expressed as that they require
a larger surface than would be naively computed by pitch * height.
Normally such requirements are hidden away in the userspace driver, but
when we accept pointers from strangers and later impose extra conditions
on them, the original client allocator has no idea about the
monstrosities in the GPU and we require the userspace driver to inform
the kernel how many padding pages are required beyond the client
allocation.

v2: Long time, no see
v3: Try an anonymous union for uapi struct compatibility
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-7-git-send-email-chris@chris-wilson.co.uk

This is not the full fix, as we are required to percolate the u64 nature
down through the drm_mm stack, but this is required now to prevent
explosions due to mismatch between execbuf (eb_vma_misplaced) and vma
binding (i915_vma_misplaced) - and reduces the risk of spurious changes
as we adjust the vma interface in the next patches.

v2: long long casts not required for u64 printk (%llx)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-6-git-send-email-chris@chris-wilson.co.uk

This reimplements the denial-of-service protection against igt from
commit 227f782e ("drm/i915: Retire requests before creating a new
one") and transfers the stall from before each batch into get_pages().
The issue is that the stall is increasing latency between batches which
is detrimental in some cases (especially coupled with execlists) to
keeping the GPU well fed. Also we have made the observation that retiring
requests can of itself free objects (and requests) and therefore makes
a good first step when shrinking.

v2: Recycle objects prior to i915_gem_object_get_pages()
v3: Remove the reference to the ring from i915_gem_requests_ring() as it
operates on an intel_engine_cs.
v4: Since commit 9b5f4e5e ("drm/i915: Retire oldest completed request
before allocating next") we no longer need the safeguard to retire
requests before get_pages(). We no longer see the huge latencies when
hitting the shrinker between allocations.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-4-git-send-email-chris@chris-wilson.co.uk

Eviction is VM local, so we can ignore the significance of the
drm_device in the caller, and leave it to i915_gem_evict_something() to
manage itself.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-2-git-send-email-chris@chris-wilson.co.uk

This reverts commit e9f24d5f.

The patch was only a stop-gap measure that fixed half the problem - the
leak of the fbcon when restarting X. A complete solution required
releasing the VMA when the object itself was closed rather than rely on
file/process exit. The previous patches add the VMA tracking necessary
to do close them along with the object, context or file, and so the time
has come to remove the partial fix.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-28-git-send-email-chris@chris-wilson.co.uk